| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
mailbox: add sanity check for channel array
Fail gracefully if there is no channel array attached to the mailbox
controller. Otherwise the later dereference will cause an OOPS which
might not be seen because mailbox controllers might instantiate very
early. Remove the comment explaining the obvious while here. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921: Place upper limit on station AID
Any station configured with an AID over 20 causes a firmware crash.
This situation occurred in our testing using an AP interface on 7922
hardware, with a modified hostapd, sourced from Mediatek's OpenWRT
feeds.
In stock hostapd, station AIDs begin counting at 1, and this
configuration is prevented with an upper limit on associated stations.
However, the modified hostapd began allocation at 65, which caused the
firmware to crash. This fix does not allow these AIDs to work, but will
prevent the firmware crash.
This crash was only seen on IFTYPE_AP interfaces, and the fix does not
appear to have an effect on IFTYPE_STATION behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/gma500/oaktrail_lvds: fix hang on init failure
The LVDS init code looks up an I2C adapter using i2c_get_adapter() and
tries to read the EDID before falling back to allocating and registering
its own adapter.
The error handling does not separate these cases so on a late init
failure it will try to deregister and free also an adapter that had
previously been registered. Since i2c_get_adapter() takes another
reference to the adapter, deregistration hangs indefinitely while
waiting for the reference to be released.
Fix this by only destroying adapters allocated during LVDS init on
errors. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/kexec: Push kjump return address even for non-kjump kexec
The version of purgatory code shipped by kexec-tools attempts to look above
the top of its stack to find a return address for a kjump, even in a non-kjump
kexec.
After the commit in Fixes: the word above the stack might not be there,
leading to a fault (which is at least now caught by my exception-handling code
in kexec).
That commit fixed things for the actual kjump path, but no longer
"gratuitously" pushes the unused return address to the stack in the non-kjump
path. Put that *back* in the non-kjump path, to prevent purgatory from
crashing when trying to access it. |
| In the Linux kernel, the following vulnerability has been resolved:
net: pull headers in qdisc_pkt_len_segs_init()
Most ndo_start_xmit() methods expects headers of gso packets
to be already in skb->head.
net/core/tso.c users are particularly at risk, because tso_build_hdr()
does a memcpy(hdr, skb->data, hdr_len);
qdisc_pkt_len_segs_init() already does a dissection of gso packets.
Use pskb_may_pull() instead of skb_header_pointer() to make
sure drivers do not have to reimplement this.
Some malicious packets could be fed, detect them so that we can
drop them sooner with a new SKB_DROP_REASON_SKB_BAD_GSO drop_reason. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Fix clone_alias() to use the original device's devid
Currently clone_alias() assumes first argument (pdev) is always the
original device pointer. This function is called by
pci_for_each_dma_alias() which based on topology decides to send
original or alias device details in first argument.
This meant that the source devid used to look up and copy the DTE
may be incorrect, leading to wrong or stale DTE entries being
propagated to alias device.
Fix this by passing the original pdev as the opaque data argument to
both the direct clone_alias() call and pci_for_each_dma_alias(). Inside
clone_alias(), retrieve the original device from data and compute devid
from it. |
| In the Linux kernel, the following vulnerability has been resolved:
pppoe: drop PFC frames
RFC 2516 Section 7 states that Protocol Field Compression (PFC) is NOT
RECOMMENDED for PPPoE. In practice, pppd does not support negotiating
PFC for PPPoE sessions, and the current PPPoE driver assumes an
uncompressed (2-byte) protocol field. However, the generic PPP layer
function ppp_input() is not aware of the negotiation result, and still
accepts PFC frames.
If a peer with a broken implementation or an attacker sends a frame with
a compressed (1-byte) protocol field, the subsequent PPP payload is
shifted by one byte. This causes the network header to be 4-byte
misaligned, which may trigger unaligned access exceptions on some
architectures.
To reduce the attack surface, drop PPPoE PFC frames. Introduce
ppp_skb_is_compressed_proto() helper function to be used in both
ppp_generic.c and pppoe.c to avoid open-coding. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: sit: reload inner IPv6 header after GSO offloads
ipip6_tunnel_xmit() caches the inner IPv6 header pointer at function
entry and continues using it after iptunnel_handle_offloads().
For GSO skbs, iptunnel_handle_offloads() calls skb_header_unclone().
When the skb header is cloned, skb_header_unclone() can call
pskb_expand_head(), which may move the skb head. The pskb_expand_head()
contract requires pointers into the skb header to be reloaded after the
call.
If the later skb_realloc_headroom() branch is not taken, SIT uses the
stale iph6 pointer to read the inner hop limit and DS field. That can
read from a freed skb head after the old head's remaining clone is
released.
Reload iph6 after the offload helper succeeds and before subsequent
reads from the inner IPv6 header. Keep the existing reload after
skb_realloc_headroom(), since that branch can also replace the skb. |
| In the Linux kernel, the following vulnerability has been resolved:
ip6_vti: fix incorrect tunnel matching in vti6_tnl_lookup()
In vti6_tnl_lookup(), when an exact match for a tunnel fails,
the code falls back to searching for wildcard tunnels:
- Tunnels matching the packet's local address, with any remote address
wildcard remote).
- Tunnels matching the packet's remote address, with any local address
(wildcard local).
However, vti6 stores all these different types of tunnels in the same
hash table (ip6n->tnls_r_l) prone to hash collisions.
The bug is that the fallback search loops in vti6_tnl_lookup() were
missing checks to ensure that the candidate tunnel actually has
a wildcard address. |
| In the Linux kernel, the following vulnerability has been resolved:
net: mvpp2: limit XDP frame size to the RX buffer
mvpp2 has short and long BM pools, and short pool buffers can be smaller
than PAGE_SIZE. The XDP path nevertheless initializes every xdp_buff with
PAGE_SIZE as frame size.
XDP helpers use frame_sz to validate tail growth and to derive the hard
end of the data area. Advertising PAGE_SIZE for short buffers can let
bpf_xdp_adjust_tail() grow a packet past the real allocation, corrupting
memory or later tripping skb tailroom checks.
Initialize the XDP buffer with bm_pool->frag_size so XDP tailroom matches
the actual buffer backing the packet. |
| In the Linux kernel, the following vulnerability has been resolved:
net: mvpp2: refill RX buffers before XDP or skb use
The RX error path returns the current descriptor buffer to the hardware
BM pool. That is only valid while the driver still owns the buffer.
mvpp2_rx_refill() can fail after the current buffer has been handed to
XDP or attached to an skb. In those cases mvpp2_run_xdp() may have
recycled, redirected, or queued the page for XDP_TX, and an skb free also
retires the data buffer. Returning such a buffer to BM lets hardware DMA
into memory that is no longer owned by the RX ring.
Refill the BM pool before handing the current buffer to XDP or to the
skb. If the allocation fails there, drop the packet and return the
still-owned current buffer to BM, preserving the pool depth. Once the
refill succeeds, later local drops retire/free the current buffer instead
of returning it to BM. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/srp: bound SRP_RSP sense copy by the received length
srp_process_rsp() copies sense data from rsp->data + resp_data_len,
where resp_data_len is the full 32-bit value supplied by the SRP target
and is never checked against the number of bytes actually received
(wc->byte_len). The copy length is bounded to SCSI_SENSE_BUFFERSIZE, so
at most 96 bytes are copied, but the source offset is not bounded.
A malicious or compromised SRP target on the InfiniBand/RoCE fabric that
the initiator has logged into can return an SRP_RSP with
SRP_RSP_FLAG_SNSVALID set and a large resp_data_len. The receive buffer
is allocated at the target-chosen max_ti_iu_len, so the source of the
sense copy lands past the bytes actually received; with resp_data_len
near 0xFFFFFFFF it is gigabytes past the buffer and the read faults.
Copy the sense data only if it has not been truncated, that is, only if
the response header, the response data, and the sense region fit within
the bytes actually received; otherwise drop the sense and log. The
in-tree iSER and NVMe-RDMA receive paths already bound their parse by
wc->byte_len; this brings ib_srp into line with them. |
| In the Linux kernel, the following vulnerability has been resolved:
ovl: keep err zero after successful ovl_cache_get()
ovl_iterate_merged() stores PTR_ERR(cache) in err before checking
IS_ERR(cache). On success err holds the truncated cache pointer and
can be returned as a bogus non-zero error.
The syzbot reproducer reaches this through overlay-on-overlay readdir:
getdents64
iterate_dir(outer overlay file)
ovl_iterate_merged()
ovl_cache_get()
ovl_dir_read_merged()
ovl_dir_read()
iterate_dir(inner overlay file)
ovl_iterate_merged()
Only compute PTR_ERR(cache) on the error path. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: require Ethernet MAC header before using eth_hdr()
`ip6t_eui64`, `xt_mac`, the `bitmap:ip,mac`, `hash:ip,mac`, and
`hash:mac` ipset types, and `nf_log_syslog` access `eth_hdr(skb)`
after either assuming that the skb is associated with an Ethernet
device or checking only that the `ETH_HLEN` bytes at
`skb_mac_header(skb)` lie between `skb->head` and `skb->data`.
Make these paths first verify that the skb is associated with an
Ethernet device, that the MAC header was set, and that it spans at
least a full Ethernet header before accessing `eth_hdr(skb)`. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/bpf: Zero-extend bpf prog return values and kfunc arguments
s390x ABI requires callers to zero-extend unsigned arguments and
sign-extend signed arguments, and callees to zero-extend unsigned
return values and sign-extend signed return values.
s390 BPF JIT currently implements only sign extension. Fix this
omission and implement zero extension too. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix stale offload->prog pointer after constant blinding
When a dev-bound-only BPF program (BPF_F_XDP_DEV_BOUND_ONLY) undergoes
JIT compilation with constant blinding enabled (bpf_jit_harden >= 2),
bpf_jit_blind_constants() clones the program. The original prog is then
freed in bpf_jit_prog_release_other(), which updates aux->prog to point
to the surviving clone, but fails to update offload->prog.
This leaves offload->prog pointing to the freed original program. When
the network namespace is subsequently destroyed, cleanup_net() triggers
bpf_dev_bound_netdev_unregister(), which iterates ondev->progs and calls
__bpf_prog_offload_destroy(offload->prog). Accessing the freed prog
causes a page fault:
BUG: unable to handle page fault for address: ffffc900085f1038
Workqueue: netns cleanup_net
RIP: 0010:__bpf_prog_offload_destroy+0xc/0x80
Call Trace:
__bpf_offload_dev_netdev_unregister+0x257/0x350
bpf_dev_bound_netdev_unregister+0x4a/0x90
unregister_netdevice_many_notify+0x2a2/0x660
...
cleanup_net+0x21a/0x320
The test sequence that triggers this reliably is:
1. Set net.core.bpf_jit_harden=2 (echo 2 > /proc/sys/net/core/bpf_jit_harden)
2. Run xdp_metadata selftest, which creates a dev-bound-only XDP
program on a veth inside a netns (./test_progs -t xdp_metadata)
3. cleanup_net -> page fault in __bpf_prog_offload_destroy
Dev-bound-only programs are unique in that they have an offload structure
but go through the normal JIT path instead of bpf_prog_offload_compile().
This means they are subject to constant blinding's prog clone-and-replace,
while also having offload->prog that must stay in sync.
Fix this by updating offload->prog in bpf_jit_prog_release_other(),
alongside the existing aux->prog update. Both are back-pointers to
the prog that must be kept in sync when the prog is replaced. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Enforce regsafe base id consistency for BPF_ADD_CONST scalars
When regsafe() compares two scalar registers that both carry
BPF_ADD_CONST, check_scalar_ids() maps their full compound id
(aka base | BPF_ADD_CONST flag) as one idmap entry. However,
it never verifies that the underlying base ids, that is, with
the flag stripped are consistent with existing idmap mappings.
This allows construction of two verifier states where the old
state has R3 = R2 + 10 (both sharing base id A) while the current
state has R3 = R4 + 10 (base id C, unrelated to R2). The idmap
creates two independent entries: A->B (for R2) and A|flag->C|flag
(for R3), without catching that A->C conflicts with A->B. State
pruning then incorrectly succeeds.
Fix this by additionally verifying base ID mapping consistency
whenever BPF_ADD_CONST is set: after mapping the compound ids,
also invoke check_ids() on the base IDs (flag bits stripped).
This ensures that if A was already mapped to B from comparing
the source register, any ADD_CONST derivative must also derive
from B, not an unrelated C. |
| In the Linux kernel, the following vulnerability has been resolved:
net/rds: Restrict use of RDS/IB to the initial network namespace
Prevent using RDS/IB in network namespaces other than the initial one.
The existing RDS/IB code will not work properly in non-initial network
namespaces. |
| In the Linux kernel, the following vulnerability has been resolved:
ppp: require CAP_NET_ADMIN in target netns for unattached ioctls
/dev/ppp open is currently authorized against file->f_cred->user_ns,
while unattached administrative ioctls operate on current->nsproxy->net_ns.
As a result, a local unprivileged user can create a new user namespace
with CLONE_NEWUSER, gain CAP_NET_ADMIN only in that new user namespace,
and still issue PPPIOCNEWUNIT, PPPIOCATTACH, or PPPIOCATTCHAN against
an inherited network namespace.
Require CAP_NET_ADMIN in the user namespace that owns the target network
namespace before handling unattached PPP administrative ioctls.
This preserves normal pppd operation in the network namespace it is
actually privileged in, while rejecting the userns-only inherited-netns
case. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/riscv: Add IOTINVAL after updating DDT/PDT entries
Add riscv_iommu_iodir_iotinval() to perform required TLB and context cache
invalidations after updating DDT or PDT entries, as mandated by the RISC-V
IOMMU specification (Section 6.3.1 and 6.3.2). |
