| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
flow_dissector: do not dissect PPPoE PFC frames
RFC 2516 Section 7 states that Protocol Field Compression (PFC) is NOT
RECOMMENDED for PPPoE. In practice, pppd does not support negotiating
PFC for PPPoE sessions, and the flow dissector driver has assumed an
uncompressed frame until the blamed commit.
During the review process of that commit [1], support for PFC is
suggested. However, having a compressed (1-byte) protocol field means
the subsequent PPP payload is shifted by one byte, causing 4-byte
misalignment for the network header and an unaligned access exception
on some architectures.
The exception can be reproduced by sending a PPPoE PFC frame to an
ethernet interface of a MIPS board, with RPS enabled, even if no PPPoE
session is active on that interface:
$ 0 : 00000000 80c40000 00000000 85144817
$ 4 : 00000008 00000100 80a75758 81dc9bb8
$ 8 : 00000010 8087ae2c 0000003d 00000000
$12 : 000000e0 00000039 00000000 00000000
$16 : 85043240 80a75758 81dc9bb8 00006488
$20 : 0000002f 00000007 85144810 80a70000
$24 : 81d1bda0 00000000
$28 : 81dc8000 81dc9aa8 00000000 805ead08
Hi : 00009d51
Lo : 2163358a
epc : 805e91f0 __skb_flow_dissect+0x1b0/0x1b50
ra : 805ead08 __skb_get_hash_net+0x74/0x12c
Status: 11000403 KERNEL EXL IE
Cause : 40800010 (ExcCode 04)
BadVA : 85144817
PrId : 0001992f (MIPS 1004Kc)
Call Trace:
[<805e91f0>] __skb_flow_dissect+0x1b0/0x1b50
[<805ead08>] __skb_get_hash_net+0x74/0x12c
[<805ef330>] get_rps_cpu+0x1b8/0x3fc
[<805fca70>] netif_receive_skb_list_internal+0x324/0x364
[<805fd120>] napi_complete_done+0x68/0x2a4
[<8058de5c>] mtk_napi_rx+0x228/0xfec
[<805fd398>] __napi_poll+0x3c/0x1c4
[<805fd754>] napi_threaded_poll_loop+0x234/0x29c
[<805fd848>] napi_threaded_poll+0x8c/0xb0
[<80053544>] kthread+0x104/0x12c
[<80002bd8>] ret_from_kernel_thread+0x14/0x1c
Code: 02d51821 1060045b 00000000 <8c640000> 3084000f 2c820005 144001a2 00042080 8e220000
To reduce the attack surface and maintain performance, do not process
PPPoE PFC frames.
[1] https://lore.kernel.org/r/20220630231016.GA392@debian.home |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_uart: fix UAFs and race conditions in close and init paths
Vulnerabilities leading to Use-After-Free (UAF) and Null Pointer
Dereference (NPD) conditions were observed in the lifecycle management
of hci_uart.
The primary issue arises because the workqueues (init_ready and
write_work) are only flushed/cancelled if the HCI_UART_PROTO_READY
flag is set during TTY close. If a hangup occurs before setup completes,
hci_uart_tty_close() skips the teardown of these workqueues and
proceeds to free the `hu` struct. When the scheduled work executes
later, it blindly dereferences the freed `hu` struct.
Furthermore, several data races and UAFs were identified in the teardown
sequence:
1. Calling hci_uart_flush() from hci_uart_close() without effectively
disabling write_work causes a race condition where both can concurrently
double-free hu->tx_skb. This happens because protocol timers can
concurrently invoke hci_uart_tx_wakeup() and requeue write_work.
2. Calling hci_free_dev(hdev) before hu->proto->close(hu) causes a UAF
when vendor specific protocol close callbacks dereference hu->hdev.
3. In the initialization error paths, failing to take the proto_lock
write lock before clearing PROTO_READY leads to races with active
readers. Additionally, hci_uart_tty_receive() accesses hu->hdev
outside the read lock, leading to UAFs if the initialization error
path frees hdev concurrently.
Fix these synchronization and lifecycle issues by:
1. Re-ordering hci_uart_tty_close() to clear HCI_UART_PROTO_READY first,
followed immediately by a cancel_work_sync(&hu->write_work). Clearing
the flag locks out concurrent protocol timers from successfully invoking
hci_uart_tx_wakeup(), effectively rendering the cancellation permanent
and preventing the tx_skb double-free.
2. Note: Clearing PROTO_READY early causes hci_uart_close() to skip
hu->proto->flush(). This is perfectly safe in the tty_close path
because hu->proto->close() executes shortly after, which intrinsically
purges all protocol SKB queues and tears down the state.
3. Relocating hu->proto->close(hu) strictly prior to hci_free_dev(hdev)
across all close and error paths to prevent vendor-level UAFs.
4. Moving the hdev->stat.byte_rx increment in hci_uart_tty_receive()
inside the proto_lock read-side critical section to safely synchronize
with device unregistration.
5. Adding cancel_work_sync(&hu->write_work) to hci_uart_close() to safely
flush the workqueue before hci_uart_flush() is invoked via the HCI core.
6. Utilizing cancel_work_sync() instead of disable_work_sync() across
all paths to prevent permanently breaking user-space retry capabilities. |
| Adobe Campaign Classic (ACC) versions 7.4.3 build 9394 and earlier are affected by an Incorrect Authorization vulnerability that could result in arbitrary code execution in the context of the current user. Exploitation of this issue does not require user interaction. Scope is changed. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: bcm-sba-raid: fix device leak on probe
Make sure to drop the reference taken when looking up the mailbox device
during probe on probe failures and on driver unbind. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/fpu: Clear XSTATE_BV[i] in guest XSAVE state whenever XFD[i]=1
When loading guest XSAVE state via KVM_SET_XSAVE, and when updating XFD in
response to a guest WRMSR, clear XFD-disabled features in the saved (or to
be restored) XSTATE_BV to ensure KVM doesn't attempt to load state for
features that are disabled via the guest's XFD. Because the kernel
executes XRSTOR with the guest's XFD, saving XSTATE_BV[i]=1 with XFD[i]=1
will cause XRSTOR to #NM and panic the kernel.
E.g. if fpu_update_guest_xfd() sets XFD without clearing XSTATE_BV:
------------[ cut here ]------------
WARNING: arch/x86/kernel/traps.c:1524 at exc_device_not_available+0x101/0x110, CPU#29: amx_test/848
Modules linked in: kvm_intel kvm irqbypass
CPU: 29 UID: 1000 PID: 848 Comm: amx_test Not tainted 6.19.0-rc2-ffa07f7fd437-x86_amx_nm_xfd_non_init-vm #171 NONE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:exc_device_not_available+0x101/0x110
Call Trace:
<TASK>
asm_exc_device_not_available+0x1a/0x20
RIP: 0010:restore_fpregs_from_fpstate+0x36/0x90
switch_fpu_return+0x4a/0xb0
kvm_arch_vcpu_ioctl_run+0x1245/0x1e40 [kvm]
kvm_vcpu_ioctl+0x2c3/0x8f0 [kvm]
__x64_sys_ioctl+0x8f/0xd0
do_syscall_64+0x62/0x940
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
---[ end trace 0000000000000000 ]---
This can happen if the guest executes WRMSR(MSR_IA32_XFD) to set XFD[18] = 1,
and a host IRQ triggers kernel_fpu_begin() prior to the vmexit handler's
call to fpu_update_guest_xfd().
and if userspace stuffs XSTATE_BV[i]=1 via KVM_SET_XSAVE:
------------[ cut here ]------------
WARNING: arch/x86/kernel/traps.c:1524 at exc_device_not_available+0x101/0x110, CPU#14: amx_test/867
Modules linked in: kvm_intel kvm irqbypass
CPU: 14 UID: 1000 PID: 867 Comm: amx_test Not tainted 6.19.0-rc2-2dace9faccd6-x86_amx_nm_xfd_non_init-vm #168 NONE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:exc_device_not_available+0x101/0x110
Call Trace:
<TASK>
asm_exc_device_not_available+0x1a/0x20
RIP: 0010:restore_fpregs_from_fpstate+0x36/0x90
fpu_swap_kvm_fpstate+0x6b/0x120
kvm_load_guest_fpu+0x30/0x80 [kvm]
kvm_arch_vcpu_ioctl_run+0x85/0x1e40 [kvm]
kvm_vcpu_ioctl+0x2c3/0x8f0 [kvm]
__x64_sys_ioctl+0x8f/0xd0
do_syscall_64+0x62/0x940
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
---[ end trace 0000000000000000 ]---
The new behavior is consistent with the AMX architecture. Per Intel's SDM,
XSAVE saves XSTATE_BV as '0' for components that are disabled via XFD
(and non-compacted XSAVE saves the initial configuration of the state
component):
If XSAVE, XSAVEC, XSAVEOPT, or XSAVES is saving the state component i,
the instruction does not generate #NM when XCR0[i] = IA32_XFD[i] = 1;
instead, it operates as if XINUSE[i] = 0 (and the state component was
in its initial state): it saves bit i of XSTATE_BV field of the XSAVE
header as 0; in addition, XSAVE saves the initial configuration of the
state component (the other instructions do not save state component i).
Alternatively, KVM could always do XRSTOR with XFD=0, e.g. by using
a constant XFD based on the set of enabled features when XSAVEing for
a struct fpu_guest. However, having XSTATE_BV[i]=1 for XFD-disabled
features can only happen in the above interrupt case, or in similar
scenarios involving preemption on preemptible kernels, because
fpu_swap_kvm_fpstate()'s call to save_fpregs_to_fpstate() saves the
outgoing FPU state with the current XFD; and that is (on all but the
first WRMSR to XFD) the guest XFD.
Therefore, XFD can only go out of sync with XSTATE_BV in the above
interrupt case, or in similar scenarios involving preemption on
preemptible kernels, and it we can consider it (de facto) part of KVM
ABI that KVM_GET_XSAVE returns XSTATE_BV[i]=0 for XFD-disabled features.
[Move clea
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: ctxfi: Fix potential OOB access in audio mixer handling
In the audio mixer handling code of ctxfi driver, the conf field is
used as a kind of loop index, and it's referred in the index callbacks
(amixer_index() and sum_index()).
As spotted recently by fuzzers, the current code causes OOB access at
those functions.
| UBSAN: array-index-out-of-bounds in /build/reproducible-path/linux-6.17.8/sound/pci/ctxfi/ctamixer.c:347:48
| index 8 is out of range for type 'unsigned char [8]'
After the analysis, the cause was found to be the lack of the proper
(re-)initialization of conj field.
This patch addresses those OOB accesses by adding the proper
initializations of the loop indices. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: sch_qfq: Fix NULL deref when deactivating inactive aggregate in qfq_reset
`qfq_class->leaf_qdisc->q.qlen > 0` does not imply that the class
itself is active.
Two qfq_class objects may point to the same leaf_qdisc. This happens
when:
1. one QFQ qdisc is attached to the dev as the root qdisc, and
2. another QFQ qdisc is temporarily referenced (e.g., via qdisc_get()
/ qdisc_put()) and is pending to be destroyed, as in function
tc_new_tfilter.
When packets are enqueued through the root QFQ qdisc, the shared
leaf_qdisc->q.qlen increases. At the same time, the second QFQ
qdisc triggers qdisc_put and qdisc_destroy: the qdisc enters
qfq_reset() with its own q->q.qlen == 0, but its class's leaf
qdisc->q.qlen > 0. Therefore, the qfq_reset would wrongly deactivate
an inactive aggregate and trigger a null-deref in qfq_deactivate_agg:
[ 0.903172] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 0.903571] #PF: supervisor write access in kernel mode
[ 0.903860] #PF: error_code(0x0002) - not-present page
[ 0.904177] PGD 10299b067 P4D 10299b067 PUD 10299c067 PMD 0
[ 0.904502] Oops: Oops: 0002 [#1] SMP NOPTI
[ 0.904737] CPU: 0 UID: 0 PID: 135 Comm: exploit Not tainted 6.19.0-rc3+ #2 NONE
[ 0.905157] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.17.0-0-gb52ca86e094d-prebuilt.qemu.org 04/01/2014
[ 0.905754] RIP: 0010:qfq_deactivate_agg (include/linux/list.h:992 (discriminator 2) include/linux/list.h:1006 (discriminator 2) net/sched/sch_qfq.c:1367 (discriminator 2) net/sched/sch_qfq.c:1393 (discriminator 2))
[ 0.906046] Code: 0f 84 4d 01 00 00 48 89 70 18 8b 4b 10 48 c7 c2 ff ff ff ff 48 8b 78 08 48 d3 e2 48 21 f2 48 2b 13 48 8b 30 48 d3 ea 8b 4b 18 0
Code starting with the faulting instruction
===========================================
0: 0f 84 4d 01 00 00 je 0x153
6: 48 89 70 18 mov %rsi,0x18(%rax)
a: 8b 4b 10 mov 0x10(%rbx),%ecx
d: 48 c7 c2 ff ff ff ff mov $0xffffffffffffffff,%rdx
14: 48 8b 78 08 mov 0x8(%rax),%rdi
18: 48 d3 e2 shl %cl,%rdx
1b: 48 21 f2 and %rsi,%rdx
1e: 48 2b 13 sub (%rbx),%rdx
21: 48 8b 30 mov (%rax),%rsi
24: 48 d3 ea shr %cl,%rdx
27: 8b 4b 18 mov 0x18(%rbx),%ecx
...
[ 0.907095] RSP: 0018:ffffc900004a39a0 EFLAGS: 00010246
[ 0.907368] RAX: ffff8881043a0880 RBX: ffff888102953340 RCX: 0000000000000000
[ 0.907723] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
[ 0.908100] RBP: ffff888102952180 R08: 0000000000000000 R09: 0000000000000000
[ 0.908451] R10: ffff8881043a0000 R11: 0000000000000000 R12: ffff888102952000
[ 0.908804] R13: ffff888102952180 R14: ffff8881043a0ad8 R15: ffff8881043a0880
[ 0.909179] FS: 000000002a1a0380(0000) GS:ffff888196d8d000(0000) knlGS:0000000000000000
[ 0.909572] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 0.909857] CR2: 0000000000000000 CR3: 0000000102993002 CR4: 0000000000772ef0
[ 0.910247] PKRU: 55555554
[ 0.910391] Call Trace:
[ 0.910527] <TASK>
[ 0.910638] qfq_reset_qdisc (net/sched/sch_qfq.c:357 net/sched/sch_qfq.c:1485)
[ 0.910826] qdisc_reset (include/linux/skbuff.h:2195 include/linux/skbuff.h:2501 include/linux/skbuff.h:3424 include/linux/skbuff.h:3430 net/sched/sch_generic.c:1036)
[ 0.911040] __qdisc_destroy (net/sched/sch_generic.c:1076)
[ 0.911236] tc_new_tfilter (net/sched/cls_api.c:2447)
[ 0.911447] rtnetlink_rcv_msg (net/core/rtnetlink.c:6958)
[ 0.911663] ? __pfx_rtnetlink_rcv_msg (net/core/rtnetlink.c:6861)
[ 0.911894] netlink_rcv_skb (net/netlink/af_netlink.c:2550)
[ 0.912100] netlink_unicast (net/netlink/af_netlink.c:1319 net/netlink/af_netlink.c:1344)
[ 0.912296] ? __alloc_skb (net/core/skbuff.c:706)
[ 0.912484] netlink_sendmsg (net/netlink/af
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
vsock/virtio: cap TX credit to local buffer size
The virtio transports derives its TX credit directly from peer_buf_alloc,
which is set from the remote endpoint's SO_VM_SOCKETS_BUFFER_SIZE value.
On the host side this means that the amount of data we are willing to
queue for a connection is scaled by a guest-chosen buffer size, rather
than the host's own vsock configuration. A malicious guest can advertise
a large buffer and read slowly, causing the host to allocate a
correspondingly large amount of sk_buff memory.
The same thing would happen in the guest with a malicious host, since
virtio transports share the same code base.
Introduce a small helper, virtio_transport_tx_buf_size(), that
returns min(peer_buf_alloc, buf_alloc), and use it wherever we consume
peer_buf_alloc.
This ensures the effective TX window is bounded by both the peer's
advertised buffer and our own buf_alloc (already clamped to
buffer_max_size via SO_VM_SOCKETS_BUFFER_MAX_SIZE), so a remote peer
cannot force the other to queue more data than allowed by its own
vsock settings.
On an unpatched Ubuntu 22.04 host (~64 GiB RAM), running a PoC with
32 guest vsock connections advertising 2 GiB each and reading slowly
drove Slab/SUnreclaim from ~0.5 GiB to ~57 GiB; the system only
recovered after killing the QEMU process. That said, if QEMU memory is
limited with cgroups, the maximum memory used will be limited.
With this patch applied:
Before:
MemFree: ~61.6 GiB
Slab: ~142 MiB
SUnreclaim: ~117 MiB
After 32 high-credit connections:
MemFree: ~61.5 GiB
Slab: ~178 MiB
SUnreclaim: ~152 MiB
Only ~35 MiB increase in Slab/SUnreclaim, no host OOM, and the guest
remains responsive.
Compatibility with non-virtio transports:
- VMCI uses the AF_VSOCK buffer knobs to size its queue pairs per
socket based on the local vsk->buffer_* values; the remote side
cannot enlarge those queues beyond what the local endpoint
configured.
- Hyper-V's vsock transport uses fixed-size VMBus ring buffers and
an MTU bound; there is no peer-controlled credit field comparable
to peer_buf_alloc, and the remote endpoint cannot drive in-flight
kernel memory above those ring sizes.
- The loopback path reuses virtio_transport_common.c, so it
naturally follows the same semantics as the virtio transport.
This change is limited to virtio_transport_common.c and thus affects
virtio-vsock, vhost-vsock, and loopback, bringing them in line with the
"remote window intersected with local policy" behaviour that VMCI and
Hyper-V already effectively have.
[Stefano: small adjustments after changing the previous patch]
[Stefano: tweak the commit message] |
| In the Linux kernel, the following vulnerability has been resolved:
can: usb_8dev: usb_8dev_read_bulk_callback(): fix URB memory leak
Fix similar memory leak as in commit 7352e1d5932a ("can: gs_usb:
gs_usb_receive_bulk_callback(): fix URB memory leak").
In usb_8dev_open() -> usb_8dev_start(), the URBs for USB-in transfers are
allocated, added to the priv->rx_submitted anchor and submitted. In the
complete callback usb_8dev_read_bulk_callback(), the URBs are processed and
resubmitted. In usb_8dev_close() -> unlink_all_urbs() the URBs are freed by
calling usb_kill_anchored_urbs(&priv->rx_submitted).
However, this does not take into account that the USB framework unanchors
the URB before the complete function is called. This means that once an
in-URB has been completed, it is no longer anchored and is ultimately not
released in usb_kill_anchored_urbs().
Fix the memory leak by anchoring the URB in the
usb_8dev_read_bulk_callback() to the priv->rx_submitted anchor. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/sysfs: cleanup attrs subdirs on context dir setup failure
When a context DAMON sysfs directory setup is failed after setup of attrs/
directory, subdirectories of attrs/ directory are not cleaned up. As a
result, DAMON sysfs interface is nearly broken until the system reboots,
and the memory for the unremoved directory is leaked.
Cleanup the directories under such failures. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: Set __nocfi on swsusp_arch_resume()
A DABT is reported[1] on an android based system when resume from hiberate.
This happens because swsusp_arch_suspend_exit() is marked with SYM_CODE_*()
and does not have a CFI hash, but swsusp_arch_resume() will attempt to
verify the CFI hash when calling a copy of swsusp_arch_suspend_exit().
Given that there's an existing requirement that the entrypoint to
swsusp_arch_suspend_exit() is the first byte of the .hibernate_exit.text
section, we cannot fix this by marking swsusp_arch_suspend_exit() with
SYM_FUNC_*(). The simplest fix for now is to disable the CFI check in
swsusp_arch_resume().
Mark swsusp_arch_resume() as __nocfi to disable the CFI check.
[1]
[ 22.991934][ T1] Unable to handle kernel paging request at virtual address 0000000109170ffc
[ 22.991934][ T1] Mem abort info:
[ 22.991934][ T1] ESR = 0x0000000096000007
[ 22.991934][ T1] EC = 0x25: DABT (current EL), IL = 32 bits
[ 22.991934][ T1] SET = 0, FnV = 0
[ 22.991934][ T1] EA = 0, S1PTW = 0
[ 22.991934][ T1] FSC = 0x07: level 3 translation fault
[ 22.991934][ T1] Data abort info:
[ 22.991934][ T1] ISV = 0, ISS = 0x00000007, ISS2 = 0x00000000
[ 22.991934][ T1] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[ 22.991934][ T1] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[ 22.991934][ T1] [0000000109170ffc] user address but active_mm is swapper
[ 22.991934][ T1] Internal error: Oops: 0000000096000007 [#1] PREEMPT SMP
[ 22.991934][ T1] Dumping ftrace buffer:
[ 22.991934][ T1] (ftrace buffer empty)
[ 22.991934][ T1] Modules linked in:
[ 22.991934][ T1] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.6.98-android15-8-g0b1d2aee7fc3-dirty-4k #1 688c7060a825a3ac418fe53881730b355915a419
[ 22.991934][ T1] Hardware name: Unisoc UMS9360-base Board (DT)
[ 22.991934][ T1] pstate: 804000c5 (Nzcv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 22.991934][ T1] pc : swsusp_arch_resume+0x2ac/0x344
[ 22.991934][ T1] lr : swsusp_arch_resume+0x294/0x344
[ 22.991934][ T1] sp : ffffffc08006b960
[ 22.991934][ T1] x29: ffffffc08006b9c0 x28: 0000000000000000 x27: 0000000000000000
[ 22.991934][ T1] x26: 0000000000000000 x25: 0000000000000000 x24: 0000000000000820
[ 22.991934][ T1] x23: ffffffd0817e3000 x22: ffffffd0817e3000 x21: 0000000000000000
[ 22.991934][ T1] x20: ffffff8089171000 x19: ffffffd08252c8c8 x18: ffffffc080061058
[ 22.991934][ T1] x17: 00000000529c6ef0 x16: 00000000529c6ef0 x15: 0000000000000004
[ 22.991934][ T1] x14: ffffff8178c88000 x13: 0000000000000006 x12: 0000000000000000
[ 22.991934][ T1] x11: 0000000000000015 x10: 0000000000000001 x9 : ffffffd082533000
[ 22.991934][ T1] x8 : 0000000109171000 x7 : 205b5d3433393139 x6 : 392e32322020205b
[ 22.991934][ T1] x5 : 000000010916f000 x4 : 000000008164b000 x3 : ffffff808a4e0530
[ 22.991934][ T1] x2 : ffffffd08058e784 x1 : 0000000082326000 x0 : 000000010a283000
[ 22.991934][ T1] Call trace:
[ 22.991934][ T1] swsusp_arch_resume+0x2ac/0x344
[ 22.991934][ T1] hibernation_restore+0x158/0x18c
[ 22.991934][ T1] load_image_and_restore+0xb0/0xec
[ 22.991934][ T1] software_resume+0xf4/0x19c
[ 22.991934][ T1] software_resume_initcall+0x34/0x78
[ 22.991934][ T1] do_one_initcall+0xe8/0x370
[ 22.991934][ T1] do_initcall_level+0xc8/0x19c
[ 22.991934][ T1] do_initcalls+0x70/0xc0
[ 22.991934][ T1] do_basic_setup+0x1c/0x28
[ 22.991934][ T1] kernel_init_freeable+0xe0/0x148
[ 22.991934][ T1] kernel_init+0x20/0x1a8
[ 22.991934][ T1] ret_from_fork+0x10/0x20
[ 22.991934][ T1] Code: a9400a61 f94013e0 f9438923 f9400a64 (b85fc110)
[catalin.marinas@arm.com: commit log updated by Mark Rutland] |
| In the Linux kernel, the following vulnerability has been resolved:
bonding: annotate data-races around slave->last_rx
slave->last_rx and slave->target_last_arp_rx[...] can be read and written
locklessly. Add READ_ONCE() and WRITE_ONCE() annotations.
syzbot reported:
BUG: KCSAN: data-race in bond_rcv_validate / bond_rcv_validate
write to 0xffff888149f0d428 of 8 bytes by interrupt on cpu 1:
bond_rcv_validate+0x202/0x7a0 drivers/net/bonding/bond_main.c:3335
bond_handle_frame+0xde/0x5e0 drivers/net/bonding/bond_main.c:1533
__netif_receive_skb_core+0x5b1/0x1950 net/core/dev.c:6039
__netif_receive_skb_one_core net/core/dev.c:6150 [inline]
__netif_receive_skb+0x59/0x270 net/core/dev.c:6265
netif_receive_skb_internal net/core/dev.c:6351 [inline]
netif_receive_skb+0x4b/0x2d0 net/core/dev.c:6410
...
write to 0xffff888149f0d428 of 8 bytes by interrupt on cpu 0:
bond_rcv_validate+0x202/0x7a0 drivers/net/bonding/bond_main.c:3335
bond_handle_frame+0xde/0x5e0 drivers/net/bonding/bond_main.c:1533
__netif_receive_skb_core+0x5b1/0x1950 net/core/dev.c:6039
__netif_receive_skb_one_core net/core/dev.c:6150 [inline]
__netif_receive_skb+0x59/0x270 net/core/dev.c:6265
netif_receive_skb_internal net/core/dev.c:6351 [inline]
netif_receive_skb+0x4b/0x2d0 net/core/dev.c:6410
br_netif_receive_skb net/bridge/br_input.c:30 [inline]
NF_HOOK include/linux/netfilter.h:318 [inline]
...
value changed: 0x0000000100005365 -> 0x0000000100005366 |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: rtl8150: fix memory leak on usb_submit_urb() failure
In async_set_registers(), when usb_submit_urb() fails, the allocated
async_req structure and URB are not freed, causing a memory leak.
The completion callback async_set_reg_cb() is responsible for freeing
these allocations, but it is only called after the URB is successfully
submitted and completes (successfully or with error). If submission
fails, the callback never runs and the memory is leaked.
Fix this by freeing both the URB and the request structure in the error
path when usb_submit_urb() fails. |
| In the Linux kernel, the following vulnerability has been resolved:
can: j1939: make j1939_session_activate() fail if device is no longer registered
syzbot is still reporting
unregister_netdevice: waiting for vcan0 to become free. Usage count = 2
even after commit 93a27b5891b8 ("can: j1939: add missing calls in
NETDEV_UNREGISTER notification handler") was added. A debug printk() patch
found that j1939_session_activate() can succeed even after
j1939_cancel_active_session() from j1939_netdev_notify(NETDEV_UNREGISTER)
has completed.
Since j1939_cancel_active_session() is processed with the session list lock
held, checking ndev->reg_state in j1939_session_activate() with the session
list lock held can reliably close the race window. |
| In the Linux kernel, the following vulnerability has been resolved:
KEYS: trusted: Fix a memory leak in tpm2_load_cmd
'tpm2_load_cmd' allocates a tempoary blob indirectly via 'tpm2_key_decode'
but it is not freed in the failure paths. Address this by wrapping the blob
into with a cleanup helper. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Fix slab-use-after-free Read in rxe_queue_cleanup bug
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x7d/0xa0 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xcf/0x610 mm/kasan/report.c:489
kasan_report+0xb5/0xe0 mm/kasan/report.c:602
rxe_queue_cleanup+0xd0/0xe0 drivers/infiniband/sw/rxe/rxe_queue.c:195
rxe_cq_cleanup+0x3f/0x50 drivers/infiniband/sw/rxe/rxe_cq.c:132
__rxe_cleanup+0x168/0x300 drivers/infiniband/sw/rxe/rxe_pool.c:232
rxe_create_cq+0x22e/0x3a0 drivers/infiniband/sw/rxe/rxe_verbs.c:1109
create_cq+0x658/0xb90 drivers/infiniband/core/uverbs_cmd.c:1052
ib_uverbs_create_cq+0xc7/0x120 drivers/infiniband/core/uverbs_cmd.c:1095
ib_uverbs_write+0x969/0xc90 drivers/infiniband/core/uverbs_main.c:679
vfs_write fs/read_write.c:677 [inline]
vfs_write+0x26a/0xcc0 fs/read_write.c:659
ksys_write+0x1b8/0x200 fs/read_write.c:731
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xaa/0x1b0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
In the function rxe_create_cq, when rxe_cq_from_init fails, the function
rxe_cleanup will be called to handle the allocated resources. In fact,
some memory resources have already been freed in the function
rxe_cq_from_init. Thus, this problem will occur.
The solution is to let rxe_cleanup do all the work. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_uart: fix null-ptr-deref in hci_uart_write_work
hci_uart_set_proto() sets HCI_UART_PROTO_INIT before calling
hci_uart_register_dev(), which calls proto->open() to initialize
hu->priv. However, if a TTY write wakeup occurs during this window,
hci_uart_tx_wakeup() may schedule write_work before hu->priv is
initialized, leading to a NULL pointer dereference in
hci_uart_write_work() when proto->dequeue() accesses hu->priv.
The race condition is:
CPU0 CPU1
---- ----
hci_uart_set_proto()
set_bit(HCI_UART_PROTO_INIT)
hci_uart_register_dev()
tty write wakeup
hci_uart_tty_wakeup()
hci_uart_tx_wakeup()
schedule_work(&hu->write_work)
proto->open(hu)
// initializes hu->priv
hci_uart_write_work()
hci_uart_dequeue()
proto->dequeue(hu)
// accesses hu->priv (NULL!)
Fix this by moving set_bit(HCI_UART_PROTO_INIT) after proto->open()
succeeds, ensuring hu->priv is initialized before any work can be
scheduled. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: uclogic: Correct devm device reference for hidinput input_dev name
Reference the HID device rather than the input device for the devm
allocation of the input_dev name. Referencing the input_dev would lead to a
use-after-free when the input_dev was unregistered and subsequently fires a
uevent that depends on the name. At the point of firing the uevent, the
name would be freed by devres management.
Use devm_kasprintf to simplify the logic for allocating memory and
formatting the input_dev name string. |
| In the Linux kernel, the following vulnerability has been resolved:
net: sock: fix hardened usercopy panic in sock_recv_errqueue
skbuff_fclone_cache was created without defining a usercopy region,
[1] unlike skbuff_head_cache which properly whitelists the cb[] field.
[2] This causes a usercopy BUG() when CONFIG_HARDENED_USERCOPY is
enabled and the kernel attempts to copy sk_buff.cb data to userspace
via sock_recv_errqueue() -> put_cmsg().
The crash occurs when: 1. TCP allocates an skb using alloc_skb_fclone()
(from skbuff_fclone_cache) [1]
2. The skb is cloned via skb_clone() using the pre-allocated fclone
[3] 3. The cloned skb is queued to sk_error_queue for timestamp
reporting 4. Userspace reads the error queue via recvmsg(MSG_ERRQUEUE)
5. sock_recv_errqueue() calls put_cmsg() to copy serr->ee from skb->cb
[4] 6. __check_heap_object() fails because skbuff_fclone_cache has no
usercopy whitelist [5]
When cloned skbs allocated from skbuff_fclone_cache are used in the
socket error queue, accessing the sock_exterr_skb structure in skb->cb
via put_cmsg() triggers a usercopy hardening violation:
[ 5.379589] usercopy: Kernel memory exposure attempt detected from SLUB object 'skbuff_fclone_cache' (offset 296, size 16)!
[ 5.382796] kernel BUG at mm/usercopy.c:102!
[ 5.383923] Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
[ 5.384903] CPU: 1 UID: 0 PID: 138 Comm: poc_put_cmsg Not tainted 6.12.57 #7
[ 5.384903] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
[ 5.384903] RIP: 0010:usercopy_abort+0x6c/0x80
[ 5.384903] Code: 1a 86 51 48 c7 c2 40 15 1a 86 41 52 48 c7 c7 c0 15 1a 86 48 0f 45 d6 48 c7 c6 80 15 1a 86 48 89 c1 49 0f 45 f3 e8 84 27 88 ff <0f> 0b 490
[ 5.384903] RSP: 0018:ffffc900006f77a8 EFLAGS: 00010246
[ 5.384903] RAX: 000000000000006f RBX: ffff88800f0ad2a8 RCX: 1ffffffff0f72e74
[ 5.384903] RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff87b973a0
[ 5.384903] RBP: 0000000000000010 R08: 0000000000000000 R09: fffffbfff0f72e74
[ 5.384903] R10: 0000000000000003 R11: 79706f6372657375 R12: 0000000000000001
[ 5.384903] R13: ffff88800f0ad2b8 R14: ffffea00003c2b40 R15: ffffea00003c2b00
[ 5.384903] FS: 0000000011bc4380(0000) GS:ffff8880bf100000(0000) knlGS:0000000000000000
[ 5.384903] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 5.384903] CR2: 000056aa3b8e5fe4 CR3: 000000000ea26004 CR4: 0000000000770ef0
[ 5.384903] PKRU: 55555554
[ 5.384903] Call Trace:
[ 5.384903] <TASK>
[ 5.384903] __check_heap_object+0x9a/0xd0
[ 5.384903] __check_object_size+0x46c/0x690
[ 5.384903] put_cmsg+0x129/0x5e0
[ 5.384903] sock_recv_errqueue+0x22f/0x380
[ 5.384903] tls_sw_recvmsg+0x7ed/0x1960
[ 5.384903] ? srso_alias_return_thunk+0x5/0xfbef5
[ 5.384903] ? schedule+0x6d/0x270
[ 5.384903] ? srso_alias_return_thunk+0x5/0xfbef5
[ 5.384903] ? mutex_unlock+0x81/0xd0
[ 5.384903] ? __pfx_mutex_unlock+0x10/0x10
[ 5.384903] ? __pfx_tls_sw_recvmsg+0x10/0x10
[ 5.384903] ? _raw_spin_lock_irqsave+0x8f/0xf0
[ 5.384903] ? _raw_read_unlock_irqrestore+0x20/0x40
[ 5.384903] ? srso_alias_return_thunk+0x5/0xfbef5
The crash offset 296 corresponds to skb2->cb within skbuff_fclones:
- sizeof(struct sk_buff) = 232 - offsetof(struct sk_buff, cb) = 40 -
offset of skb2.cb in fclones = 232 + 40 = 272 - crash offset 296 =
272 + 24 (inside sock_exterr_skb.ee)
This patch uses a local stack variable as a bounce buffer to avoid the hardened usercopy check failure.
[1] https://elixir.bootlin.com/linux/v6.12.62/source/net/ipv4/tcp.c#L885
[2] https://elixir.bootlin.com/linux/v6.12.62/source/net/core/skbuff.c#L5104
[3] https://elixir.bootlin.com/linux/v6.12.62/source/net/core/skbuff.c#L5566
[4] https://elixir.bootlin.com/linux/v6.12.62/source/net/core/skbuff.c#L5491
[5] https://elixir.bootlin.com/linux/v6.12.62/source/mm/slub.c#L5719 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rsi: Fix memory corruption due to not set vif driver data size
The struct ieee80211_vif contains trailing space for vif driver data,
when struct ieee80211_vif is allocated, the total memory size that is
allocated is sizeof(struct ieee80211_vif) + size of vif driver data.
The size of vif driver data is set by each WiFi driver as needed.
The RSI911x driver does not set vif driver data size, no trailing space
for vif driver data is therefore allocated past struct ieee80211_vif .
The RSI911x driver does however use the vif driver data to store its
vif driver data structure "struct vif_priv". An access to vif->drv_priv
leads to access out of struct ieee80211_vif bounds and corruption of
some memory.
In case of the failure observed locally, rsi_mac80211_add_interface()
would write struct vif_priv *vif_info = (struct vif_priv *)vif->drv_priv;
vif_info->vap_id = vap_idx. This write corrupts struct fq_tin member
struct list_head new_flows . The flow = list_first_entry(head, struct
fq_flow, flowchain); in fq_tin_reset() then reports non-NULL bogus
address, which when accessed causes a crash.
The trigger is very simple, boot the machine with init=/bin/sh , mount
devtmpfs, sysfs, procfs, and then do "ip link set wlan0 up", "sleep 1",
"ip link set wlan0 down" and the crash occurs.
Fix this by setting the correct size of vif driver data, which is the
size of "struct vif_priv", so that memory is allocated and the driver
can store its driver data in it, instead of corrupting memory around
it. |
