| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/kbuf: check if target buffer list is still legacy on recycle
There's a gap between when the buffer was grabbed and when it
potentially gets recycled, where if the list is empty, someone could've
upgraded it to a ring provided type. This can happen if the request
is forced via io-wq. The legacy recycling is missing checking if the
buffer_list still exists, and if it's of the correct type. Add those
checks. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: fix undersized l_iclog_roundoff values
If the superblock doesn't list a log stripe unit, we set the incore log
roundoff value to 512. This leads to corrupt logs and unmountable
filesystems in generic/617 on a disk with 4k physical sectors...
XFS (sda1): Mounting V5 Filesystem ff3121ca-26e6-4b77-b742-aaff9a449e1c
XFS (sda1): Torn write (CRC failure) detected at log block 0x318e. Truncating head block from 0x3197.
XFS (sda1): failed to locate log tail
XFS (sda1): log mount/recovery failed: error -74
XFS (sda1): log mount failed
XFS (sda1): Mounting V5 Filesystem ff3121ca-26e6-4b77-b742-aaff9a449e1c
XFS (sda1): Ending clean mount
...on the current xfsprogs for-next which has a broken mkfs. xfs_info
shows this...
meta-data=/dev/sda1 isize=512 agcount=4, agsize=644992 blks
= sectsz=4096 attr=2, projid32bit=1
= crc=1 finobt=1, sparse=1, rmapbt=1
= reflink=1 bigtime=1 inobtcount=1 nrext64=1
= exchange=1 metadir=1
data = bsize=4096 blocks=2579968, imaxpct=25
= sunit=0 swidth=0 blks
naming =version 2 bsize=4096 ascii-ci=0, ftype=1, parent=1
log =internal log bsize=4096 blocks=16384, version=2
= sectsz=4096 sunit=0 blks, lazy-count=1
realtime =none extsz=4096 blocks=0, rtextents=0
= rgcount=0 rgsize=268435456 extents
= zoned=0 start=0 reserved=0
...observe that the log section has sectsz=4096 sunit=0, which means
that the roundoff factor is 512, not 4096 as you'd expect. We should
fix mkfs not to generate broken filesystems, but anyone can fuzz the
ondisk superblock so we should be more cautious. I think the inadequate
logic predates commit a6a65fef5ef8d0, but that's clearly going to
require a different backport. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/apic: Disable x2apic on resume if the kernel expects so
When resuming from s2ram, firmware may re-enable x2apic mode, which may have
been disabled by the kernel during boot either because it doesn't support IRQ
remapping or for other reasons. This causes the kernel to continue using the
xapic interface, while the hardware is in x2apic mode, which causes hangs.
This happens on defconfig + bare metal + s2ram.
Fix this in lapic_resume() by disabling x2apic if the kernel expects it to be
disabled, i.e. when x2apic_mode = 0.
The ACPI v6.6 spec, Section 16.3 [1] says firmware restores either the
pre-sleep configuration or initial boot configuration for each CPU, including
MSR state:
When executing from the power-on reset vector as a result of waking from an
S2 or S3 sleep state, the platform firmware performs only the hardware
initialization required to restore the system to either the state the
platform was in prior to the initial operating system boot, or to the
pre-sleep configuration state. In multiprocessor systems, non-boot
processors should be placed in the same state as prior to the initial
operating system boot.
(further ahead)
If this is an S2 or S3 wake, then the platform runtime firmware restores
minimum context of the system before jumping to the waking vector. This
includes:
CPU configuration. Platform runtime firmware restores the pre-sleep
configuration or initial boot configuration of each CPU (MSR, MTRR,
firmware update, SMBase, and so on). Interrupts must be disabled (for
IA-32 processors, disabled by CLI instruction).
(and other things)
So at least as per the spec, re-enablement of x2apic by the firmware is
allowed if "x2apic on" is a part of the initial boot configuration.
[1] https://uefi.org/specs/ACPI/6.6/16_Waking_and_Sleeping.html#initialization
[ bp: Massage. ] |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix in-place encryption corruption in SMB2_write()
SMB2_write() places write payload in iov[1..n] as part of rq_iov.
smb3_init_transform_rq() pointer-shares rq_iov, so crypt_message()
encrypts iov[1] in-place, replacing the original plaintext with
ciphertext. On a replayable error, the retry sends the same iov[1]
which now contains ciphertext instead of the original data,
resulting in corruption.
The corruption is most likely to be observed when connections are
unstable, as reconnects trigger write retries that re-send the
already-encrypted data.
This affects SFU mknod, MF symlinks, etc. On kernels before
6.10 (prior to the netfs conversion), sync writes also used
this path and were similarly affected. The async write path
wasn't unaffected as it uses rq_iter which gets deep-copied.
Fix by moving the write payload into rq_iter via iov_iter_kvec(),
so smb3_init_transform_rq() deep-copies it before encryption. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: gyro: mpu3050-core: fix pm_runtime error handling
The return value of pm_runtime_get_sync() is not checked, allowing
the driver to access hardware that may fail to resume. The device
usage count is also unconditionally incremented. Use
pm_runtime_resume_and_get() which propagates errors and avoids
incrementing the usage count on failure.
In preenable, add pm_runtime_put_autosuspend() on set_8khz_samplerate()
failure since postdisable does not run when preenable fails. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915: Fix potential overflow of shmem scatterlist length
When a scatterlists table of a GEM shmem object of size 4 GB or more is
populated with pages allocated from a folio, unsigned int .length
attribute of a scatterlist may get overflowed if total byte length of
pages allocated to that single scatterlist happens to reach or cross the
4GB limit. As a consequence, users of the object may suffer from hitting
unexpected, premature end of the object's backing pages.
[278.780187] ------------[ cut here ]------------
[278.780377] WARNING: CPU: 1 PID: 2326 at drivers/gpu/drm/i915/i915_mm.c:55 remap_sg+0x199/0x1d0 [i915]
...
[278.780654] CPU: 1 UID: 0 PID: 2326 Comm: gem_mmap_offset Tainted: G S U 6.17.0-rc1-CI_DRM_16981-ged823aaa0607+ #1 PREEMPT(voluntary)
[278.780656] Tainted: [S]=CPU_OUT_OF_SPEC, [U]=USER
[278.780658] Hardware name: Intel Corporation Meteor Lake Client Platform/MTL-P LP5x T3 RVP, BIOS MTLPFWI1.R00.3471.D91.2401310918 01/31/2024
[278.780659] RIP: 0010:remap_sg+0x199/0x1d0 [i915]
...
[278.780786] Call Trace:
[278.780787] <TASK>
[278.780788] ? __apply_to_page_range+0x3e6/0x910
[278.780795] ? __pfx_remap_sg+0x10/0x10 [i915]
[278.780906] apply_to_page_range+0x14/0x30
[278.780908] remap_io_sg+0x14d/0x260 [i915]
[278.781013] vm_fault_cpu+0xd2/0x330 [i915]
[278.781137] __do_fault+0x3a/0x1b0
[278.781140] do_fault+0x322/0x640
[278.781143] __handle_mm_fault+0x938/0xfd0
[278.781150] handle_mm_fault+0x12c/0x300
[278.781152] ? lock_mm_and_find_vma+0x4b/0x760
[278.781155] do_user_addr_fault+0x2d6/0x8e0
[278.781160] exc_page_fault+0x96/0x2c0
[278.781165] asm_exc_page_fault+0x27/0x30
...
That issue was apprehended by the author of a change that introduced it,
and potential risk even annotated with a comment, but then never addressed.
When adding folio pages to a scatterlist table, take care of byte length
of any single scatterlist not exceeding max_segment.
(cherry picked from commit 06249b4e691a75694c014a61708c007fb5755f60) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Fix use-after-free race in VM acquire
Replace non-atomic vm->process_info assignment with cmpxchg()
to prevent race when parent/child processes sharing a drm_file
both try to acquire the same VM after fork().
(cherry picked from commit c7c573275ec20db05be769288a3e3bb2250ec618) |
| In the Linux kernel, the following vulnerability has been resolved:
net: macb: Shuffle the tx ring before enabling tx
Quanyang observed that when using an NFS rootfs on an AMD ZynqMp board,
the rootfs may take an extended time to recover after a suspend.
Upon investigation, it was determined that the issue originates from a
problem in the macb driver.
According to the Zynq UltraScale TRM [1], when transmit is disabled,
the transmit buffer queue pointer resets to point to the address
specified by the transmit buffer queue base address register.
In the current implementation, the code merely resets `queue->tx_head`
and `queue->tx_tail` to '0'. This approach presents several issues:
- Packets already queued in the tx ring are silently lost,
leading to memory leaks since the associated skbs cannot be released.
- Concurrent write access to `queue->tx_head` and `queue->tx_tail` may
occur from `macb_tx_poll()` or `macb_start_xmit()` when these values
are reset to '0'.
- The transmission may become stuck on a packet that has already been sent
out, with its 'TX_USED' bit set, but has not yet been processed. However,
due to the manipulation of 'queue->tx_head' and 'queue->tx_tail',
`macb_tx_poll()` incorrectly assumes there are no packets to handle
because `queue->tx_head == queue->tx_tail`. This issue is only resolved
when a new packet is placed at this position. This is the root cause of
the prolonged recovery time observed for the NFS root filesystem.
To resolve this issue, shuffle the tx ring and tx skb array so that
the first unsent packet is positioned at the start of the tx ring.
Additionally, ensure that updates to `queue->tx_head` and
`queue->tx_tail` are properly protected with the appropriate lock.
[1] https://docs.amd.com/v/u/en-US/ug1085-zynq-ultrascale-trm |
| In the Linux kernel, the following vulnerability has been resolved:
net: ncsi: fix skb leak in error paths
Early return paths in NCSI RX and AEN handlers fail to release
the received skb, resulting in a memory leak.
Specifically, ncsi_aen_handler() returns on invalid AEN packets
without consuming the skb. Similarly, ncsi_rcv_rsp() exits early
when failing to resolve the NCSI device, response handler, or
request, leaving the skb unfreed. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix transaction abort on set received ioctl due to item overflow
If the set received ioctl fails due to an item overflow when attempting to
add the BTRFS_UUID_KEY_RECEIVED_SUBVOL we have to abort the transaction
since we did some metadata updates before.
This means that if a user calls this ioctl with the same received UUID
field for a lot of subvolumes, we will hit the overflow, trigger the
transaction abort and turn the filesystem into RO mode. A malicious user
could exploit this, and this ioctl does not even requires that a user
has admin privileges (CAP_SYS_ADMIN), only that he/she owns the subvolume.
Fix this by doing an early check for item overflow before starting a
transaction. This is also race safe because we are holding the subvol_sem
semaphore in exclusive (write) mode.
A test case for fstests will follow soon. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: Don't log keys in SMB3 signing and encryption key generation
When KSMBD_DEBUG_AUTH logging is enabled, generate_smb3signingkey() and
generate_smb3encryptionkey() log the session, signing, encryption, and
decryption key bytes. Remove the logs to avoid exposing credentials. |
| In the Linux kernel, the following vulnerability has been resolved:
octeontx2-af: Workaround SQM/PSE stalls by disabling sticky
NIX SQ manager sticky mode is known to cause stalls when multiple SQs
share an SMQ and transmit concurrently. Additionally, PSE may deadlock
on transitions between sticky and non-sticky transmissions. There is
also a credit drop issue observed when certain condition clocks are
gated.
work around these hardware errata by:
- Disabling SQM sticky operation:
- Clear TM6 (bit 15)
- Clear TM11 (bit 14)
- Disabling sticky → non-sticky transition path that can deadlock PSE:
- Clear TM5 (bit 23)
- Preventing credit drops by keeping the control-flow clock enabled:
- Set TM9 (bit 21)
These changes are applied via NIX_AF_SQM_DBG_CTL_STATUS. With this
configuration the SQM/PSE maintain forward progress under load without
credit loss, at the cost of disabling sticky optimizations. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/v3d: Set DMA segment size to avoid debug warnings
When using V3D rendering with CONFIG_DMA_API_DEBUG enabled, the
kernel occasionally reports a segment size mismatch. This is because
'max_seg_size' is not set. The kernel defaults to 64K. setting
'max_seg_size' to the maximum will prevent 'debug_dma_map_sg()'
from complaining about the over-mapping of the V3D segment length.
DMA-API: v3d 1002000000.v3d: mapping sg segment longer than device
claims to support [len=8290304] [max=65536]
WARNING: CPU: 0 PID: 493 at kernel/dma/debug.c:1179 debug_dma_map_sg+0x330/0x388
CPU: 0 UID: 0 PID: 493 Comm: Xorg Not tainted 6.12.53-yocto-standard #1
Hardware name: Raspberry Pi 5 Model B Rev 1.0 (DT)
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : debug_dma_map_sg+0x330/0x388
lr : debug_dma_map_sg+0x330/0x388
sp : ffff8000829a3ac0
x29: ffff8000829a3ac0 x28: 0000000000000001 x27: ffff8000813fe000
x26: ffffc1ffc0000000 x25: ffff00010fdeb760 x24: 0000000000000000
x23: ffff8000816a9bf0 x22: 0000000000000001 x21: 0000000000000002
x20: 0000000000000002 x19: ffff00010185e810 x18: ffffffffffffffff
x17: 69766564206e6168 x16: 74207265676e6f6c x15: 20746e656d676573
x14: 20677320676e6970 x13: 5d34303334393134 x12: 0000000000000000
x11: 00000000000000c0 x10: 00000000000009c0 x9 : ffff8000800e0b7c
x8 : ffff00010a315ca0 x7 : ffff8000816a5110 x6 : 0000000000000001
x5 : 000000000000002b x4 : 0000000000000002 x3 : 0000000000000008
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff00010a315280
Call trace:
debug_dma_map_sg+0x330/0x388
__dma_map_sg_attrs+0xc0/0x278
dma_map_sgtable+0x30/0x58
drm_gem_shmem_get_pages_sgt+0xb4/0x140
v3d_bo_create_finish+0x28/0x130 [v3d]
v3d_create_bo_ioctl+0x54/0x180 [v3d]
drm_ioctl_kernel+0xc8/0x140
drm_ioctl+0x2d4/0x4d8 |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix transaction abort on file creation due to name hash collision
If we attempt to create several files with names that result in the same
hash, we have to pack them in same dir item and that has a limit inherent
to the leaf size. However if we reach that limit, we trigger a transaction
abort and turns the filesystem into RO mode. This allows for a malicious
user to disrupt a system, without the need to have administration
privileges/capabilities.
Reproducer:
$ cat exploit-hash-collisions.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
# Use smallest node size to make the test faster and require fewer file
# names that result in hash collision.
mkfs.btrfs -f --nodesize 4K $DEV
mount $DEV $MNT
# List of names that result in the same crc32c hash for btrfs.
declare -a names=(
'foobar'
'%a8tYkxfGMLWRGr55QSeQc4PBNH9PCLIvR6jZnkDtUUru1t@RouaUe_L:@xGkbO3nCwvLNYeK9vhE628gss:T$yZjZ5l-Nbd6CbC$M=hqE-ujhJICXyIxBvYrIU9-TDC'
'AQci3EUB%shMsg-N%frgU:02ByLs=IPJU0OpgiWit5nexSyxZDncY6WB:=zKZuk5Zy0DD$Ua78%MelgBuMqaHGyKsJUFf9s=UW80PcJmKctb46KveLSiUtNmqrMiL9-Y0I_l5Fnam04CGIg=8@U:Z'
'CvVqJpJzueKcuA$wqwePfyu7VxuWNN3ho$p0zi2H8QFYK$7YlEqOhhb%:hHgjhIjW5vnqWHKNP4'
'ET:vk@rFU4tsvMB0$C_p=xQHaYZjvoF%-BTc%wkFW8yaDAPcCYoR%x$FH5O:'
'HwTon%v7SGSP4FE08jBwwiu5aot2CFKXHTeEAa@38fUcNGOWvE@Mz6WBeDH_VooaZ6AgsXPkVGwy9l@@ZbNXabUU9csiWrrOp0MWUdfi$EZ3w9GkIqtz7I_eOsByOkBOO'
'Ij%2VlFGXSuPvxJGf5UWy6O@1svxGha%b@=%wjkq:CIgE6u7eJOjmQY5qTtxE2Rjbis9@us'
'KBkjG5%9R8K9sOG8UTnAYjxLNAvBmvV5vz3IiZaPmKuLYO03-6asI9lJ_j4@6Xo$KZicaLWJ3Pv8XEwVeUPMwbHYWwbx0pYvNlGMO9F:ZhHAwyctnGy%_eujl%WPd4U2BI7qooOSr85J-C2V$LfY'
'NcRfDfuUQ2=zP8K3CCF5dFcpfiOm6mwenShsAb_F%n6GAGC7fT2JFFn:c35X-3aYwoq7jNX5$ZJ6hI3wnZs$7KgGi7wjulffhHNUxAT0fRRLF39vJ@NvaEMxsMO'
'Oj42AQAEzRoTxa5OuSKIr=A_lwGMy132v4g3Pdq1GvUG9874YseIFQ6QU'
'Ono7avN5GjC:_6dBJ_'
'WHmN2gnmaN-9dVDy4aWo:yNGFzz8qsJyJhWEWcud7$QzN2D9R0efIWWEdu5kwWr73NZm4=@CoCDxrrZnRITr-kGtU_cfW2:%2_am'
'WiFnuTEhAG9FEC6zopQmj-A-$LDQ0T3WULz%ox3UZAPybSV6v1Z$b4L_XBi4M4BMBtJZpz93r9xafpB77r:lbwvitWRyo$odnAUYlYMmU4RvgnNd--e=I5hiEjGLETTtaScWlQp8mYsBovZwM2k'
'XKyH=OsOAF3p%uziGF_ZVr$ivrvhVgD@1u%5RtrV-gl_vqAwHkK@x7YwlxX3qT6WKKQ%PR56NrUBU2dOAOAdzr2=5nJuKPM-T-$ZpQfCL7phxQbUcb:BZOTPaFExc-qK-gDRCDW2'
'd3uUR6OFEwZr%ns1XH_@tbxA@cCPmbBRLdyh7p6V45H$P2$F%w0RqrD3M0g8aGvWpoTFMiBdOTJXjD:JF7=h9a_43xBywYAP%r$SPZi%zDg%ql-KvkdUCtF9OLaQlxmd'
'ePTpbnit%hyNm@WELlpKzNZYOzOTf8EQ$sEfkMy1VOfIUu3coyvIr13-Y7Sv5v-Ivax2Go_GQRFMU1b3362nktT9WOJf3SpT%z8sZmM3gvYQBDgmKI%%RM-G7hyrhgYflOw%z::ZRcv5O:lDCFm'
'evqk743Y@dvZAiG5J05L_ROFV@$2%rVWJ2%3nxV72-W7$e$-SK3tuSHA2mBt$qloC5jwNx33GmQUjD%akhBPu=VJ5g$xhlZiaFtTrjeeM5x7dt4cHpX0cZkmfImndYzGmvwQG:$euFYmXn$_2rA9mKZ'
'gkgUtnihWXsZQTEkrMAWIxir09k3t7jk_IK25t1:cy1XWN0GGqC%FrySdcmU7M8MuPO_ppkLw3=Dfr0UuBAL4%GFk2$Ma10V1jDRGJje%Xx9EV2ERaWKtjpwiZwh0gCSJsj5UL7CR8RtW5opCVFKGGy8Cky'
'hNgsG_8lNRik3PvphqPm0yEH3P%%fYG:kQLY=6O-61Wa6nrV_WVGR6TLB09vHOv%g4VQRP8Gzx7VXUY1qvZyS'
'isA7JVzN12xCxVPJZ_qoLm-pTBuhjjHMvV7o=F:EaClfYNyFGlsfw-Kf%uxdqW-kwk1sPl2vhbjyHU1A6$hz'
'kiJ_fgcdZFDiOptjgH5PN9-PSyLO4fbk_:u5_2tz35lV_iXiJ6cx7pwjTtKy-XGaQ5IefmpJ4N_ZqGsqCsKuqOOBgf9LkUdffHet@Wu'
'lvwtxyhE9:%Q3UxeHiViUyNzJsy:fm38pg_b6s25JvdhOAT=1s0$pG25x=LZ2rlHTszj=gN6M4zHZYr_qrB49i=pA--@WqWLIuX7o1S_SfS@2FSiUZN'
'rC24cw3UBDZ=5qJBUMs9e$=S4Y94ni%Z8639vnrGp=0Hv4z3dNFL0fBLmQ40=EYIY:Z=SLc@QLMSt2zsss2ZXrP7j4='
'uwGl2s-fFrf@GqS=DQqq2I0LJSsOmM%xzTjS:lzXguE3wChdMoHYtLRKPvfaPOZF2fER@j53evbKa7R%A7r4%YEkD=kicJe@SFiGtXHbKe4gCgPAYbnVn'
'UG37U6KKua2bgc:IHzRs7BnB6FD:2Mt5Cc5NdlsW%$1tyvnfz7S27FvNkroXwAW:mBZLA1@qa9WnDbHCDmQmfPMC9z-Eq6QT0jhhPpqyymaD:R02ghwYo%yx7SAaaq-:x33LYpei$5g8DMl3C'
'y2vjek0FE1PDJC0qpfnN:x8k2wCFZ9xiUF2ege=JnP98R%wxjKkdfEiLWvQzmnW'
'8-HCSgH5B%K7P8_jaVtQhBXpBk:pE-$P7ts58U0J@iR9YZntMPl7j$s62yAJO@_9eanFPS54b=UTw$94C-t=HLxT8n6o9P=QnIxq-f1=Ne2dvhe6WbjEQtc'
'YPPh:IFt2mtR6XWSmjHptXL_hbSYu8bMw-JP8@PNyaFkdNFsk$M=xfL6LDKCDM-mSyGA_2MBwZ8Dr4=R1D%7-mC
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix transaction abort when snapshotting received subvolumes
Currently a user can trigger a transaction abort by snapshotting a
previously received snapshot a bunch of times until we reach a
BTRFS_UUID_KEY_RECEIVED_SUBVOL item overflow (the maximum item size we
can store in a leaf). This is very likely not common in practice, but
if it happens, it turns the filesystem into RO mode. The snapshot, send
and set_received_subvol and subvol_setflags (used by receive) don't
require CAP_SYS_ADMIN, just inode_owner_or_capable(). A malicious user
could use this to turn a filesystem into RO mode and disrupt a system.
Reproducer script:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
# Use smallest node size to make the test faster.
mkfs.btrfs -f --nodesize 4K $DEV
mount $DEV $MNT
# Create a subvolume and set it to RO so that it can be used for send.
btrfs subvolume create $MNT/sv
touch $MNT/sv/foo
btrfs property set $MNT/sv ro true
# Send and receive the subvolume into snaps/sv.
mkdir $MNT/snaps
btrfs send $MNT/sv | btrfs receive $MNT/snaps
# Now snapshot the received subvolume, which has a received_uuid, a
# lot of times to trigger the leaf overflow.
total=500
for ((i = 1; i <= $total; i++)); do
echo -ne "\rCreating snapshot $i/$total"
btrfs subvolume snapshot -r $MNT/snaps/sv $MNT/snaps/sv_$i > /dev/null
done
echo
umount $MNT
When running the test:
$ ./test.sh
(...)
Create subvolume '/mnt/sdi/sv'
At subvol /mnt/sdi/sv
At subvol sv
Creating snapshot 496/500ERROR: Could not create subvolume: Value too large for defined data type
Creating snapshot 497/500ERROR: Could not create subvolume: Read-only file system
Creating snapshot 498/500ERROR: Could not create subvolume: Read-only file system
Creating snapshot 499/500ERROR: Could not create subvolume: Read-only file system
Creating snapshot 500/500ERROR: Could not create subvolume: Read-only file system
And in dmesg/syslog:
$ dmesg
(...)
[251067.627338] BTRFS warning (device sdi): insert uuid item failed -75 (0x4628b21c4ac8d898, 0x2598bee2b1515c91) type 252!
[251067.629212] ------------[ cut here ]------------
[251067.630033] BTRFS: Transaction aborted (error -75)
[251067.630871] WARNING: fs/btrfs/transaction.c:1907 at create_pending_snapshot.cold+0x52/0x465 [btrfs], CPU#10: btrfs/615235
[251067.632851] Modules linked in: btrfs dm_zero (...)
[251067.644071] CPU: 10 UID: 0 PID: 615235 Comm: btrfs Tainted: G W 6.19.0-rc8-btrfs-next-225+ #1 PREEMPT(full)
[251067.646165] Tainted: [W]=WARN
[251067.646733] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org 04/01/2014
[251067.648735] RIP: 0010:create_pending_snapshot.cold+0x55/0x465 [btrfs]
[251067.649984] Code: f0 48 0f (...)
[251067.653313] RSP: 0018:ffffce644908fae8 EFLAGS: 00010292
[251067.653987] RAX: 00000000ffffff01 RBX: ffff8e5639e63a80 RCX: 00000000ffffffd3
[251067.655042] RDX: ffff8e53faa76b00 RSI: 00000000ffffffb5 RDI: ffffffffc0919750
[251067.656077] RBP: ffffce644908fbd8 R08: 0000000000000000 R09: ffffce644908f820
[251067.657068] R10: ffff8e5adc1fffa8 R11: 0000000000000003 R12: ffff8e53c0431bd0
[251067.658050] R13: ffff8e5414593600 R14: ffff8e55efafd000 R15: 00000000ffffffb5
[251067.659019] FS: 00007f2a4944b3c0(0000) GS:ffff8e5b27dae000(0000) knlGS:0000000000000000
[251067.660115] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[251067.660943] CR2: 00007ffc5aa57898 CR3: 00000005813a2003 CR4: 0000000000370ef0
[251067.661972] Call Trace:
[251067.662292] <TASK>
[251067.662653] create_pending_snapshots+0x97/0xc0 [btrfs]
[251067.663413] btrfs_commit_transaction+0x26e/0xc00 [btrfs]
[251067.664257] ? btrfs_qgroup_convert_reserved_meta+0x35/0x390 [btrfs]
[251067.665238] ? _raw_spin_unlock+0x15/0x30
[251067.665837] ? record_root_
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net: nfc: nci: Fix parameter validation for packet data
Since commit 9c328f54741b ("net: nfc: nci: Add parameter validation for
packet data") communication with nci nfc chips is not working any more.
The mentioned commit tries to fix access of uninitialized data, but
failed to understand that in some cases the data packet is of variable
length and can therefore not be compared to the maximum packet length
given by the sizeof(struct). |
| In the Linux kernel, the following vulnerability has been resolved:
rapidio: replace rio_free_net() with kfree() in rio_scan_alloc_net()
When idtab allocation fails, net is not registered with rio_add_net() yet,
so kfree(net) is sufficient to release the memory. Set mport->net to NULL
to avoid dangling pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Fix deadlock in l2cap_conn_del()
l2cap_conn_del() calls cancel_delayed_work_sync() for both info_timer
and id_addr_timer while holding conn->lock. However, the work functions
l2cap_info_timeout() and l2cap_conn_update_id_addr() both acquire
conn->lock, creating a potential AB-BA deadlock if the work is already
executing when l2cap_conn_del() takes the lock.
Move the work cancellations before acquiring conn->lock and use
disable_delayed_work_sync() to additionally prevent the works from
being rearmed after cancellation, consistent with the pattern used in
hci_conn_del(). |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: amd: acp3x-rt5682-max9836: Add missing error check for clock acquisition
The acp3x_5682_init() function did not check the return value of
clk_get(), which could lead to dereferencing error pointers in
rt5682_clk_enable().
Fix this by:
1. Changing clk_get() to the device-managed devm_clk_get().
2. Adding proper IS_ERR() checks for both clock acquisitions. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Set/clear CR8 write interception when AVIC is (de)activated
Explicitly set/clear CR8 write interception when AVIC is (de)activated to
fix a bug where KVM leaves the interception enabled after AVIC is
activated. E.g. if KVM emulates INIT=>WFS while AVIC is deactivated, CR8
will remain intercepted in perpetuity.
On its own, the dangling CR8 intercept is "just" a performance issue, but
combined with the TPR sync bug fixed by commit d02e48830e3f ("KVM: SVM:
Sync TPR from LAPIC into VMCB::V_TPR even if AVIC is active"), the danging
intercept is fatal to Windows guests as the TPR seen by hardware gets
wildly out of sync with reality.
Note, VMX isn't affected by the bug as TPR_THRESHOLD is explicitly ignored
when Virtual Interrupt Delivery is enabled, i.e. when APICv is active in
KVM's world. I.e. there's no need to trigger update_cr8_intercept(), this
is firmly an SVM implementation flaw/detail.
WARN if KVM gets a CR8 write #VMEXIT while AVIC is active, as KVM should
never enter the guest with AVIC enabled and CR8 writes intercepted.
[Squash fix to avic_deactivate_vmcb. - Paolo] |
