| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: consume xmit errors of GSO frames
udpgro_frglist.sh and udpgro_bench.sh are the flakiest tests
currently in NIPA. They fail in the same exact way, TCP GRO
test stalls occasionally and the test gets killed after 10min.
These tests use veth to simulate GRO. They attach a trivial
("return XDP_PASS;") XDP program to the veth to force TSO off
and NAPI on.
Digging into the failure mode we can see that the connection
is completely stuck after a burst of drops. The sender's snd_nxt
is at sequence number N [1], but the receiver claims to have
received (rcv_nxt) up to N + 3 * MSS [2]. Last piece of the puzzle
is that senders rtx queue is not empty (let's say the block in
the rtx queue is at sequence number N - 4 * MSS [3]).
In this state, sender sends a retransmission from the rtx queue
with a single segment, and sequence numbers N-4*MSS:N-3*MSS [3].
Receiver sees it and responds with an ACK all the way up to
N + 3 * MSS [2]. But sender will reject this ack as TCP_ACK_UNSENT_DATA
because it has no recollection of ever sending data that far out [1].
And we are stuck.
The root cause is the mess of the xmit return codes. veth returns
an error when it can't xmit a frame. We end up with a loss event
like this:
-------------------------------------------------
| GSO super frame 1 | GSO super frame 2 |
|-----------------------------------------------|
| seg | seg | seg | seg | seg | seg | seg | seg |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
-------------------------------------------------
x ok ok <ok>| ok ok ok <x>
\\
snd_nxt
"x" means packet lost by veth, and "ok" means it went thru.
Since veth has TSO disabled in this test it sees individual segments.
Segment 1 is on the retransmit queue and will be resent.
So why did the sender not advance snd_nxt even tho it clearly did
send up to seg 8? tcp_write_xmit() interprets the return code
from the core to mean that data has not been sent at all. Since
TCP deals with GSO super frames, not individual segment the crux
of the problem is that loss of a single segment can be interpreted
as loss of all. TCP only sees the last return code for the last
segment of the GSO frame (in <> brackets in the diagram above).
Of course for the problem to occur we need a setup or a device
without a Qdisc. Otherwise Qdisc layer disconnects the protocol
layer from the device errors completely.
We have multiple ways to fix this.
1) make veth not return an error when it lost a packet.
While this is what I think we did in the past, the issue keeps
reappearing and it's annoying to debug. The game of whack
a mole is not great.
2) fix the damn return codes
We only talk about NETDEV_TX_OK and NETDEV_TX_BUSY in the
documentation, so maybe we should make the return code from
ndo_start_xmit() a boolean. I like that the most, but perhaps
some ancient, not-really-networking protocol would suffer.
3) make TCP ignore the errors
It is not entirely clear to me what benefit TCP gets from
interpreting the result of ip_queue_xmit()? Specifically once
the connection is established and we're pushing data - packet
loss is just packet loss?
4) this fix
Ignore the rc in the Qdisc-less+GSO case, since it's unreliable.
We already always return OK in the TCQ_F_CAN_BYPASS case.
In the Qdisc-less case let's be a bit more conservative and only
mask the GSO errors. This path is taken by non-IP-"networks"
like CAN, MCTP etc, so we could regress some ancient thing.
This is the simplest, but also maybe the hackiest fix?
Similar fix has been proposed by Eric in the past but never committed
because original reporter was working with an OOT driver and wasn't
providing feedback (see Link). |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: endpoint: Fix swapped parameters in pci_{primary/secondary}_epc_epf_unlink() functions
struct configfs_item_operations callbacks are defined like the following:
int (*allow_link)(struct config_item *src, struct config_item *target);
void (*drop_link)(struct config_item *src, struct config_item *target);
While pci_primary_epc_epf_link() and pci_secondary_epc_epf_link() specify
the parameters in the correct order, pci_primary_epc_epf_unlink() and
pci_secondary_epc_epf_unlink() specify the parameters in the wrong order,
leading to the below kernel crash when using the unlink command in
configfs:
Unable to handle kernel paging request at virtual address 0000000300000857
Mem abort info:
...
pc : string+0x54/0x14c
lr : vsnprintf+0x280/0x6e8
...
string+0x54/0x14c
vsnprintf+0x280/0x6e8
vprintk_default+0x38/0x4c
vprintk+0xc4/0xe0
pci_epf_unbind+0xdc/0x108
configfs_unlink+0xe0/0x208+0x44/0x74
vfs_unlink+0x120/0x29c
__arm64_sys_unlinkat+0x3c/0x90
invoke_syscall+0x48/0x134
do_el0_svc+0x1c/0x30prop.0+0xd0/0xf0
[mani: cced stable, changed commit message as per https://lore.kernel.org/linux-pci/aV9joi3jF1R6ca02@ryzen] |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: vt8500lcdfb: fix missing dma_free_coherent()
fbi->fb.screen_buffer is allocated with dma_alloc_coherent() but is not
freed if the error path is reached. |
| In the Linux kernel, the following vulnerability has been resolved:
atm: fore200e: fix use-after-free in tasklets during device removal
When the PCA-200E or SBA-200E adapter is being detached, the fore200e
is deallocated. However, the tx_tasklet or rx_tasklet may still be running
or pending, leading to use-after-free bug when the already freed fore200e
is accessed again in fore200e_tx_tasklet() or fore200e_rx_tasklet().
One of the race conditions can occur as follows:
CPU 0 (cleanup) | CPU 1 (tasklet)
fore200e_pca_remove_one() | fore200e_interrupt()
fore200e_shutdown() | tasklet_schedule()
kfree(fore200e) | fore200e_tx_tasklet()
| fore200e-> // UAF
Fix this by ensuring tx_tasklet or rx_tasklet is properly canceled before
the fore200e is released. Add tasklet_kill() in fore200e_shutdown() to
synchronize with any pending or running tasklets. Moreover, since
fore200e_reset() could prevent further interrupts or data transfers,
the tasklet_kill() should be placed after fore200e_reset() to prevent
the tasklet from being rescheduled in fore200e_interrupt(). Finally,
it only needs to do tasklet_kill() when the fore200e state is greater
than or equal to FORE200E_STATE_IRQ, since tasklets are uninitialized
in earlier states. In a word, the tasklet_kill() should be placed in
the FORE200E_STATE_IRQ branch within the switch...case structure.
This bug was identified through static analysis. |
| In the Linux kernel, the following vulnerability has been resolved:
minix: Add required sanity checking to minix_check_superblock()
The fs/minix implementation of the minix filesystem does not currently
support any other value for s_log_zone_size than 0. This is also the
only value supported in util-linux; see mkfs.minix.c line 511. In
addition, this patch adds some sanity checking for the other minix
superblock fields, and moves the minix_blocks_needed() checks for the
zmap and imap also to minix_check_super_block().
This also closes a related syzbot bug report. |
| In the Linux kernel, the following vulnerability has been resolved:
dpaa2-switch: validate num_ifs to prevent out-of-bounds write
The driver obtains sw_attr.num_ifs from firmware via dpsw_get_attributes()
but never validates it against DPSW_MAX_IF (64). This value controls
iteration in dpaa2_switch_fdb_get_flood_cfg(), which writes port indices
into the fixed-size cfg->if_id[DPSW_MAX_IF] array. When firmware reports
num_ifs >= 64, the loop can write past the array bounds.
Add a bound check for num_ifs in dpaa2_switch_init().
dpaa2_switch_fdb_get_flood_cfg() appends the control interface (port
num_ifs) after all matched ports. When num_ifs == DPSW_MAX_IF and all
ports match the flood filter, the loop fills all 64 slots and the control
interface write overflows by one entry.
The check uses >= because num_ifs == DPSW_MAX_IF is also functionally
broken.
build_if_id_bitmap() silently drops any ID >= 64:
if (id[i] < DPSW_MAX_IF)
bmap[id[i] / 64] |= ... |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: Fix pci_slot_trylock() error handling
Commit a4e772898f8b ("PCI: Add missing bridge lock to pci_bus_lock()")
delegates the bridge device's pci_dev_trylock() to pci_bus_trylock() in
pci_slot_trylock(), but it forgets to remove the corresponding
pci_dev_unlock() when pci_bus_trylock() fails.
Before a4e772898f8b, the code did:
if (!pci_dev_trylock(dev)) /* <- lock bridge device */
goto unlock;
if (dev->subordinate) {
if (!pci_bus_trylock(dev->subordinate)) {
pci_dev_unlock(dev); /* <- unlock bridge device */
goto unlock;
}
}
After a4e772898f8b the bridge-device lock is no longer taken, but the
pci_dev_unlock(dev) on the failure path was left in place, leading to the
bug.
This yields one of two errors:
1. A warning that the lock is being unlocked when no one holds it.
2. An incorrect unlock of a lock that belongs to another thread.
Fix it by removing the now-redundant pci_dev_unlock(dev) on the failure
path.
[Same patch later posted by Keith at
https://patch.msgid.link/20260116184150.3013258-1-kbusch@meta.com] |
| In the Linux kernel, the following vulnerability has been resolved:
USB: gadget: Fix obscure lockdep violation for udc_mutex
A recent commit expanding the scope of the udc_lock mutex in the
gadget core managed to cause an obscure and slightly bizarre lockdep
violation. In abbreviated form:
======================================================
WARNING: possible circular locking dependency detected
5.19.0-rc7+ #12510 Not tainted
------------------------------------------------------
udevadm/312 is trying to acquire lock:
ffff80000aae1058 (udc_lock){+.+.}-{3:3}, at: usb_udc_uevent+0x54/0xe0
but task is already holding lock:
ffff000002277548 (kn->active#4){++++}-{0:0}, at: kernfs_seq_start+0x34/0xe0
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (kn->active#4){++++}-{0:0}:
lock_acquire+0x68/0x84
__kernfs_remove+0x268/0x380
kernfs_remove_by_name_ns+0x58/0xac
sysfs_remove_file_ns+0x18/0x24
device_del+0x15c/0x440
-> #2 (device_links_lock){+.+.}-{3:3}:
lock_acquire+0x68/0x84
__mutex_lock+0x9c/0x430
mutex_lock_nested+0x38/0x64
device_link_remove+0x3c/0xa0
_regulator_put.part.0+0x168/0x190
regulator_put+0x3c/0x54
devm_regulator_release+0x14/0x20
-> #1 (regulator_list_mutex){+.+.}-{3:3}:
lock_acquire+0x68/0x84
__mutex_lock+0x9c/0x430
mutex_lock_nested+0x38/0x64
regulator_lock_dependent+0x54/0x284
regulator_enable+0x34/0x80
phy_power_on+0x24/0x130
__dwc2_lowlevel_hw_enable+0x100/0x130
dwc2_lowlevel_hw_enable+0x18/0x40
dwc2_hsotg_udc_start+0x6c/0x2f0
gadget_bind_driver+0x124/0x1f4
-> #0 (udc_lock){+.+.}-{3:3}:
__lock_acquire+0x1298/0x20cc
lock_acquire.part.0+0xe0/0x230
lock_acquire+0x68/0x84
__mutex_lock+0x9c/0x430
mutex_lock_nested+0x38/0x64
usb_udc_uevent+0x54/0xe0
Evidently this was caused by the scope of udc_mutex being too large.
The mutex is only meant to protect udc->driver along with a few other
things. As far as I can tell, there's no reason for the mutex to be
held while the gadget core calls a gadget driver's ->bind or ->unbind
routine, or while a UDC is being started or stopped. (This accounts
for link #1 in the chain above, where the mutex is held while the
dwc2_hsotg_udc is started as part of driver probing.)
Gadget drivers' ->disconnect callbacks are problematic. Even though
usb_gadget_disconnect() will now acquire the udc_mutex, there's a
window in usb_gadget_bind_driver() between the times when the mutex is
released and the ->bind callback is invoked. If a disconnect occurred
during that window, we could call the driver's ->disconnect routine
before its ->bind routine. To prevent this from happening, it will be
necessary to prevent a UDC from connecting while it has no gadget
driver. This should be done already but it doesn't seem to be;
currently usb_gadget_connect() has no check for this. Such a check
will have to be added later.
Some degree of mutual exclusion is required in soft_connect_store(),
which can dereference udc->driver at arbitrary times since it is a
sysfs callback. The solution here is to acquire the gadget's device
lock rather than the udc_mutex. Since the driver core guarantees that
the device lock is always held during driver binding and unbinding,
this will make the accesses in soft_connect_store() mutually exclusive
with any changes to udc->driver.
Lastly, it turns out there is one place which should hold the
udc_mutex but currently does not: The function_show() routine needs
protection while it dereferences udc->driver. The missing lock and
unlock calls are added. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: prodikeys: Check presence of pm->input_ep82
Fake USB devices can send their own report descriptors for which the
input_mapping() hook does not get called. In this case, pm->input_ep82 stays
NULL, which leads to a crash later.
This does not happen with the real device, but can be provoked by imposing as
one. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: pm: in-kernel: always set ID as avail when rm endp
Syzkaller managed to find a combination of actions that was generating
this warning:
WARNING: net/mptcp/pm_kernel.c:1074 at __mark_subflow_endp_available net/mptcp/pm_kernel.c:1074 [inline], CPU#1: syz.7.48/2535
WARNING: net/mptcp/pm_kernel.c:1074 at mptcp_pm_nl_fullmesh net/mptcp/pm_kernel.c:1446 [inline], CPU#1: syz.7.48/2535
WARNING: net/mptcp/pm_kernel.c:1074 at mptcp_pm_nl_set_flags_all net/mptcp/pm_kernel.c:1474 [inline], CPU#1: syz.7.48/2535
WARNING: net/mptcp/pm_kernel.c:1074 at mptcp_pm_nl_set_flags+0x5de/0x640 net/mptcp/pm_kernel.c:1538, CPU#1: syz.7.48/2535
Modules linked in:
CPU: 1 UID: 0 PID: 2535 Comm: syz.7.48 Not tainted 6.18.0-03987-gea5f5e676cf5 #17 PREEMPT(voluntary)
Hardware name: QEMU Ubuntu 25.10 PC (i440FX + PIIX, 1996), BIOS 1.17.0-debian-1.17.0-1 04/01/2014
RIP: 0010:__mark_subflow_endp_available net/mptcp/pm_kernel.c:1074 [inline]
RIP: 0010:mptcp_pm_nl_fullmesh net/mptcp/pm_kernel.c:1446 [inline]
RIP: 0010:mptcp_pm_nl_set_flags_all net/mptcp/pm_kernel.c:1474 [inline]
RIP: 0010:mptcp_pm_nl_set_flags+0x5de/0x640 net/mptcp/pm_kernel.c:1538
Code: 89 c7 e8 c5 8c 73 fe e9 f7 fd ff ff 49 83 ef 80 e8 b7 8c 73 fe 4c 89 ff be 03 00 00 00 e8 4a 29 e3 fe eb ac e8 a3 8c 73 fe 90 <0f> 0b 90 e9 3d ff ff ff e8 95 8c 73 fe b8 a1 ff ff ff eb 1a e8 89
RSP: 0018:ffffc9001535b820 EFLAGS: 00010287
netdevsim0: tun_chr_ioctl cmd 1074025677
RAX: ffffffff82da294d RBX: 0000000000000001 RCX: 0000000000080000
RDX: ffffc900096d0000 RSI: 00000000000006d6 RDI: 00000000000006d7
netdevsim0: linktype set to 823
RBP: ffff88802cdb2240 R08: 00000000000104ae R09: ffffffffffffffff
R10: ffffffff82da27d4 R11: 0000000000000000 R12: 0000000000000000
R13: ffff88801246d8c0 R14: ffffc9001535b8b8 R15: ffff88802cdb1800
FS: 00007fc6ac5a76c0(0000) GS:ffff8880f90c8000(0000) knlGS:0000000000000000
netlink: 'syz.3.50': attribute type 5 has an invalid length.
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
netlink: 1232 bytes leftover after parsing attributes in process `syz.3.50'.
CR2: 0000200000010000 CR3: 0000000025b1a000 CR4: 0000000000350ef0
Call Trace:
<TASK>
mptcp_pm_set_flags net/mptcp/pm_netlink.c:277 [inline]
mptcp_pm_nl_set_flags_doit+0x1d7/0x210 net/mptcp/pm_netlink.c:282
genl_family_rcv_msg_doit+0x117/0x180 net/netlink/genetlink.c:1115
genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline]
genl_rcv_msg+0x3a8/0x3f0 net/netlink/genetlink.c:1210
netlink_rcv_skb+0x16d/0x240 net/netlink/af_netlink.c:2550
genl_rcv+0x28/0x40 net/netlink/genetlink.c:1219
netlink_unicast_kernel net/netlink/af_netlink.c:1318 [inline]
netlink_unicast+0x3e9/0x4c0 net/netlink/af_netlink.c:1344
netlink_sendmsg+0x4ab/0x5b0 net/netlink/af_netlink.c:1894
sock_sendmsg_nosec net/socket.c:718 [inline]
__sock_sendmsg+0xc9/0xf0 net/socket.c:733
____sys_sendmsg+0x272/0x3b0 net/socket.c:2608
___sys_sendmsg+0x2de/0x320 net/socket.c:2662
__sys_sendmsg net/socket.c:2694 [inline]
__do_sys_sendmsg net/socket.c:2699 [inline]
__se_sys_sendmsg net/socket.c:2697 [inline]
__x64_sys_sendmsg+0x110/0x1a0 net/socket.c:2697
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xed/0x360 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fc6adb66f6d
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fc6ac5a6ff8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007fc6addf5fa0 RCX: 00007fc6adb66f6d
RDX: 0000000000048084 RSI: 00002000000002c0 RDI: 000000000000000e
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 000000000000
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mvm: fix potential out-of-bounds read in iwl_mvm_nd_match_info_handler()
The memcpy function assumes the dynamic array notif->matches is at least
as large as the number of bytes to copy. Otherwise, results->matches may
contain unwanted data. To guarantee safety, extend the validation in one
of the checks to ensure sufficient packet length.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (occ) Fix division by zero in occ_show_power_1()
In occ_show_power_1() case 1, the accumulator is divided by
update_tag without checking for zero. If no samples have been
collected yet (e.g. during early boot when the sensor block is
included but hasn't been updated), update_tag is zero, causing
a kernel divide-by-zero crash.
The 2019 fix in commit 211186cae14d ("hwmon: (occ) Fix division by
zero issue") only addressed occ_get_powr_avg() used by
occ_show_power_2() and occ_show_power_a0(). This separate code
path in occ_show_power_1() was missed.
Fix this by reusing the existing occ_get_powr_avg() helper, which
already handles the zero-sample case and uses mul_u64_u32_div()
to multiply before dividing for better precision. Move the helper
above occ_show_power_1() so it is visible at the call site.
[groeck: Fix alignment problems reported by checkpatch] |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ti-adc161s626: use DMA-safe memory for spi_read()
Add a DMA-safe buffer and use it for spi_read() instead of a stack
memory. All SPI buffers must be DMA-safe.
Since we only need up to 3 bytes, we just use a u8[] instead of __be16
and __be32 and change the conversion functions appropriately. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915/dsi: Don't do DSC horizontal timing adjustments in command mode
Stop adjusting the horizontal timing values based on the
compression ratio in command mode. Bspec seems to be telling
us to do this only in video mode, and this is also how the
Windows driver does things.
This should also fix a div-by-zero on some machines because
the adjusted htotal ends up being so small that we end up with
line_time_us==0 when trying to determine the vtotal value in
command mode.
Note that this doesn't actually make the display on the
Huawei Matebook E work, but at least the kernel no longer
explodes when the driver loads.
(cherry picked from commit 0b475e91ecc2313207196c6d7fd5c53e1a878525) |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: account XFRMA_IF_ID in aevent size calculation
xfrm_get_ae() allocates the reply skb with xfrm_aevent_msgsize(), then
build_aevent() appends attributes including XFRMA_IF_ID when x->if_id is
set.
xfrm_aevent_msgsize() does not include space for XFRMA_IF_ID. For states
with if_id, build_aevent() can fail with -EMSGSIZE and hit BUG_ON(err < 0)
in xfrm_get_ae(), turning a malformed netlink interaction into a kernel
panic.
Account XFRMA_IF_ID in the size calculation unconditionally and replace
the BUG_ON with normal error unwinding. |
| In the Linux kernel, the following vulnerability has been resolved:
ntb: ntb_hw_switchtec: Fix array-index-out-of-bounds access
Number of MW LUTs depends on NTB configuration and can be set to MAX_MWS,
This patch protects against invalid index out of bounds access to mw_sizes
When invalid access print message to user that configuration is not valid. |
| In the Linux kernel, the following vulnerability has been resolved:
soc: ti: k3-socinfo: Fix regmap leak on probe failure
The mmio regmap allocated during probe is never freed.
Switch to using the device managed allocator so that the regmap is
released on probe failures (e.g. probe deferral) and on driver unbind. |
| In the Linux kernel, the following vulnerability has been resolved:
media: i2c/tw9906: Fix potential memory leak in tw9906_probe()
In one of the error paths in tw9906_probe(), the memory allocated in
v4l2_ctrl_handler_init() and v4l2_ctrl_new_std() is not freed. Fix that
by calling v4l2_ctrl_handler_free() on the handler in that error path. |
| In the Linux kernel, the following vulnerability has been resolved:
dm: remove fake timeout to avoid leak request
Since commit 15f73f5b3e59 ("blk-mq: move failure injection out of
blk_mq_complete_request"), drivers are responsible for calling
blk_should_fake_timeout() at appropriate code paths and opportunities.
However, the dm driver does not implement its own timeout handler and
relies on the timeout handling of its slave devices.
If an io-timeout-fail error is injected to a dm device, the request
will be leaked and never completed, causing tasks to hang indefinitely.
Reproduce:
1. prepare dm which has iscsi slave device
2. inject io-timeout-fail to dm
echo 1 >/sys/class/block/dm-0/io-timeout-fail
echo 100 >/sys/kernel/debug/fail_io_timeout/probability
echo 10 >/sys/kernel/debug/fail_io_timeout/times
3. read/write dm
4. iscsiadm -m node -u
Result: hang task like below
[ 862.243768] INFO: task kworker/u514:2:151 blocked for more than 122 seconds.
[ 862.244133] Tainted: G E 6.19.0-rc1+ #51
[ 862.244337] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 862.244718] task:kworker/u514:2 state:D stack:0 pid:151 tgid:151 ppid:2 task_flags:0x4288060 flags:0x00080000
[ 862.245024] Workqueue: iscsi_ctrl_3:1 __iscsi_unbind_session [scsi_transport_iscsi]
[ 862.245264] Call Trace:
[ 862.245587] <TASK>
[ 862.245814] __schedule+0x810/0x15c0
[ 862.246557] schedule+0x69/0x180
[ 862.246760] blk_mq_freeze_queue_wait+0xde/0x120
[ 862.247688] elevator_change+0x16d/0x460
[ 862.247893] elevator_set_none+0x87/0xf0
[ 862.248798] blk_unregister_queue+0x12e/0x2a0
[ 862.248995] __del_gendisk+0x231/0x7e0
[ 862.250143] del_gendisk+0x12f/0x1d0
[ 862.250339] sd_remove+0x85/0x130 [sd_mod]
[ 862.250650] device_release_driver_internal+0x36d/0x530
[ 862.250849] bus_remove_device+0x1dd/0x3f0
[ 862.251042] device_del+0x38a/0x930
[ 862.252095] __scsi_remove_device+0x293/0x360
[ 862.252291] scsi_remove_target+0x486/0x760
[ 862.252654] __iscsi_unbind_session+0x18a/0x3e0 [scsi_transport_iscsi]
[ 862.252886] process_one_work+0x633/0xe50
[ 862.253101] worker_thread+0x6df/0xf10
[ 862.253647] kthread+0x36d/0x720
[ 862.254533] ret_from_fork+0x2a6/0x470
[ 862.255852] ret_from_fork_asm+0x1a/0x30
[ 862.256037] </TASK>
Remove the blk_should_fake_timeout() check from dm, as dm has no
native timeout handling and should not attempt to fake timeouts. |
| In the Linux kernel, the following vulnerability has been resolved:
NFC: pn533: bound the UART receive buffer
pn532_receive_buf() appends every incoming byte to dev->recv_skb and
only resets the buffer after pn532_uart_rx_is_frame() recognizes a
complete frame. A continuous stream of bytes without a valid PN532 frame
header therefore keeps growing the skb until skb_put_u8() hits the tail
limit.
Drop the accumulated partial frame once the fixed receive buffer is full
so malformed UART traffic cannot grow the skb past
PN532_UART_SKB_BUFF_LEN. |
