| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Cap MSIX used to online CPUs + 1
The irdma driver can use a maximum number of msix vectors equal
to num_online_cpus() + 1 and the kernel warning stack below is shown
if that number is exceeded.
The kernel throws a warning as the driver tries to update the affinity
hint with a CPU mask greater than the max CPU IDs. Fix this by capping
the MSIX vectors to num_online_cpus() + 1.
WARNING: CPU: 7 PID: 23655 at include/linux/cpumask.h:106 irdma_cfg_ceq_vector+0x34c/0x3f0 [irdma]
RIP: 0010:irdma_cfg_ceq_vector+0x34c/0x3f0 [irdma]
Call Trace:
irdma_rt_init_hw+0xa62/0x1290 [irdma]
? irdma_alloc_local_mac_entry+0x1a0/0x1a0 [irdma]
? __is_kernel_percpu_address+0x63/0x310
? rcu_read_lock_held_common+0xe/0xb0
? irdma_lan_unregister_qset+0x280/0x280 [irdma]
? irdma_request_reset+0x80/0x80 [irdma]
? ice_get_qos_params+0x84/0x390 [ice]
irdma_probe+0xa40/0xfc0 [irdma]
? rcu_read_lock_bh_held+0xd0/0xd0
? irdma_remove+0x140/0x140 [irdma]
? rcu_read_lock_sched_held+0x62/0xe0
? down_write+0x187/0x3d0
? auxiliary_match_id+0xf0/0x1a0
? irdma_remove+0x140/0x140 [irdma]
auxiliary_bus_probe+0xa6/0x100
__driver_probe_device+0x4a4/0xd50
? __device_attach_driver+0x2c0/0x2c0
driver_probe_device+0x4a/0x110
__driver_attach+0x1aa/0x350
bus_for_each_dev+0x11d/0x1b0
? subsys_dev_iter_init+0xe0/0xe0
bus_add_driver+0x3b1/0x610
driver_register+0x18e/0x410
? 0xffffffffc0b88000
irdma_init_module+0x50/0xaa [irdma]
do_one_initcall+0x103/0x5f0
? perf_trace_initcall_level+0x420/0x420
? do_init_module+0x4e/0x700
? __kasan_kmalloc+0x7d/0xa0
? kmem_cache_alloc_trace+0x188/0x2b0
? kasan_unpoison+0x21/0x50
do_init_module+0x1d1/0x700
load_module+0x3867/0x5260
? layout_and_allocate+0x3990/0x3990
? rcu_read_lock_held_common+0xe/0xb0
? rcu_read_lock_sched_held+0x62/0xe0
? rcu_read_lock_bh_held+0xd0/0xd0
? __vmalloc_node_range+0x46b/0x890
? lock_release+0x5c8/0xba0
? alloc_vm_area+0x120/0x120
? selinux_kernel_module_from_file+0x2a5/0x300
? __inode_security_revalidate+0xf0/0xf0
? __do_sys_init_module+0x1db/0x260
__do_sys_init_module+0x1db/0x260
? load_module+0x5260/0x5260
? do_syscall_64+0x22/0x450
do_syscall_64+0xa5/0x450
entry_SYSCALL_64_after_hwframe+0x66/0xdb |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: Fix dropping valid root bus resources with .end = zero
On r8a7791/koelsch:
kmemleak: 1 new suspected memory leaks (see /sys/kernel/debug/kmemleak)
# cat /sys/kernel/debug/kmemleak
unreferenced object 0xc3a34e00 (size 64):
comm "swapper/0", pid 1, jiffies 4294937460 (age 199.080s)
hex dump (first 32 bytes):
b4 5d 81 f0 b4 5d 81 f0 c0 b0 a2 c3 00 00 00 00 .]...]..........
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<fe3aa979>] __kmalloc+0xf0/0x140
[<34bd6bc0>] resource_list_create_entry+0x18/0x38
[<767046bc>] pci_add_resource_offset+0x20/0x68
[<b3f3edf2>] devm_of_pci_get_host_bridge_resources.constprop.0+0xb0/0x390
When coalescing two resources for a contiguous aperture, the second
resource is enlarged to cover the full contiguous range, while the first
resource is marked invalid. This invalidation is done by clearing the
flags, start, and end members.
When adding the initial resources to the bus later, invalid resources are
skipped. Unfortunately, the check for an invalid resource considers only
the end member, causing false positives.
E.g. on r8a7791/koelsch, root bus resource 0 ("bus 00") is skipped, and no
longer registered with pci_bus_insert_busn_res() (causing the memory leak),
nor printed:
pci-rcar-gen2 ee090000.pci: host bridge /soc/pci@ee090000 ranges:
pci-rcar-gen2 ee090000.pci: MEM 0x00ee080000..0x00ee08ffff -> 0x00ee080000
pci-rcar-gen2 ee090000.pci: PCI: revision 11
pci-rcar-gen2 ee090000.pci: PCI host bridge to bus 0000:00
-pci_bus 0000:00: root bus resource [bus 00]
pci_bus 0000:00: root bus resource [mem 0xee080000-0xee08ffff]
Fix this by only skipping resources where all of the flags, start, and end
members are zero. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Fix NULL pointer dereference in VRAM logic for APU devices
Previously, APU platforms (and other scenarios with uninitialized VRAM managers)
triggered a NULL pointer dereference in `ttm_resource_manager_usage()`. The root
cause is not that the `struct ttm_resource_manager *man` pointer itself is NULL,
but that `man->bdev` (the backing device pointer within the manager) remains
uninitialized (NULL) on APUs—since APUs lack dedicated VRAM and do not fully
set up VRAM manager structures. When `ttm_resource_manager_usage()` attempts to
acquire `man->bdev->lru_lock`, it dereferences the NULL `man->bdev`, leading to
a kernel OOPS.
1. **amdgpu_cs.c**: Extend the existing bandwidth control check in
`amdgpu_cs_get_threshold_for_moves()` to include a check for
`ttm_resource_manager_used()`. If the manager is not used (uninitialized
`bdev`), return 0 for migration thresholds immediately—skipping VRAM-specific
logic that would trigger the NULL dereference.
2. **amdgpu_kms.c**: Update the `AMDGPU_INFO_VRAM_USAGE` ioctl and memory info
reporting to use a conditional: if the manager is used, return the real VRAM
usage; otherwise, return 0. This avoids accessing `man->bdev` when it is
NULL.
3. **amdgpu_virt.c**: Modify the vf2pf (virtual function to physical function)
data write path. Use `ttm_resource_manager_used()` to check validity: if the
manager is usable, calculate `fb_usage` from VRAM usage; otherwise, set
`fb_usage` to 0 (APUs have no discrete framebuffer to report).
This approach is more robust than APU-specific checks because it:
- Works for all scenarios where the VRAM manager is uninitialized (not just APUs),
- Aligns with TTM's design by using its native helper function,
- Preserves correct behavior for discrete GPUs (which have fully initialized
`man->bdev` and pass the `ttm_resource_manager_used()` check).
v4: use ttm_resource_manager_used(&adev->mman.vram_mgr.manager) instead of checking the adev->gmc.is_app_apu flag (Christian) |
| In the Linux kernel, the following vulnerability has been resolved:
loop: loop_set_status_from_info() check before assignment
In loop_set_status_from_info(), lo->lo_offset and lo->lo_sizelimit should
be checked before reassignment, because if an overflow error occurs, the
original correct value will be changed to the wrong value, and it will not
be changed back.
More, the original patch did not solve the problem, the value was set and
ioctl returned an error, but the subsequent io used the value in the loop
driver, which still caused an alarm:
loop_handle_cmd
do_req_filebacked
loff_t pos = ((loff_t) blk_rq_pos(rq) << 9) + lo->lo_offset;
lo_rw_aio
cmd->iocb.ki_pos = pos |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: Fix memory leak in vmw_mksstat_add_ioctl()
If the copy of the description string from userspace fails, then the page
for the instance descriptor doesn't get freed before returning -EFAULT,
which leads to a memleak. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: serial: ip22zilog: Use platform device for probing
After commit 84a9582fd203 ("serial: core: Start managing serial controllers
to enable runtime PM") serial drivers need to provide a device in
struct uart_port.dev otherwise an oops happens. To fix this issue
for ip22zilog driver switch driver to a platform driver and setup
the serial device in sgi-ip22 code. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: htc_hst: free skb in ath9k_htc_rx_msg() if there is no callback function
It is stated that ath9k_htc_rx_msg() either frees the provided skb or
passes its management to another callback function. However, the skb is
not freed in case there is no another callback function, and Syzkaller was
able to cause a memory leak. Also minor comment fix.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
arch_topology: Fix incorrect error check in topology_parse_cpu_capacity()
Fix incorrect use of PTR_ERR_OR_ZERO() in topology_parse_cpu_capacity()
which causes the code to proceed with NULL clock pointers. The current
logic uses !PTR_ERR_OR_ZERO(cpu_clk) which evaluates to true for both
valid pointers and NULL, leading to potential NULL pointer dereference
in clk_get_rate().
Per include/linux/err.h documentation, PTR_ERR_OR_ZERO(ptr) returns:
"The error code within @ptr if it is an error pointer; 0 otherwise."
This means PTR_ERR_OR_ZERO() returns 0 for both valid pointers AND NULL
pointers. Therefore !PTR_ERR_OR_ZERO(cpu_clk) evaluates to true (proceed)
when cpu_clk is either valid or NULL, causing clk_get_rate(NULL) to be
called when of_clk_get() returns NULL.
Replace with !IS_ERR_OR_NULL(cpu_clk) which only proceeds for valid
pointers, preventing potential NULL pointer dereference in clk_get_rate(). |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: bcsp: receive data only if registered
Currently, bcsp_recv() can be called even when the BCSP protocol has not
been registered. This leads to a NULL pointer dereference, as shown in
the following stack trace:
KASAN: null-ptr-deref in range [0x0000000000000108-0x000000000000010f]
RIP: 0010:bcsp_recv+0x13d/0x1740 drivers/bluetooth/hci_bcsp.c:590
Call Trace:
<TASK>
hci_uart_tty_receive+0x194/0x220 drivers/bluetooth/hci_ldisc.c:627
tiocsti+0x23c/0x2c0 drivers/tty/tty_io.c:2290
tty_ioctl+0x626/0xde0 drivers/tty/tty_io.c:2706
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl+0xfc/0x170 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
To prevent this, ensure that the HCI_UART_REGISTERED flag is set before
processing received data. If the protocol is not registered, return
-EUNATCH. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Fix NULL pointer dereference in snd_usb_mixer_controls_badd
In snd_usb_create_streams(), for UAC version 3 devices, the Interface
Association Descriptor (IAD) is retrieved via usb_ifnum_to_if(). If this
call fails, a fallback routine attempts to obtain the IAD from the next
interface and sets a BADD profile. However, snd_usb_mixer_controls_badd()
assumes that the IAD retrieved from usb_ifnum_to_if() is always valid,
without performing a NULL check. This can lead to a NULL pointer
dereference when usb_ifnum_to_if() fails to find the interface descriptor.
This patch adds a NULL pointer check after calling usb_ifnum_to_if() in
snd_usb_mixer_controls_badd() to prevent the dereference.
This issue was discovered by syzkaller, which triggered the bug by sending
a crafted USB device descriptor. |
| In the Linux kernel, the following vulnerability has been resolved:
cpufreq: intel_pstate: Fix object lifecycle issue in update_qos_request()
The cpufreq_cpu_put() call in update_qos_request() takes place too early
because the latter subsequently calls freq_qos_update_request() that
indirectly accesses the policy object in question through the QoS request
object passed to it.
Fortunately, update_qos_request() is called under intel_pstate_driver_lock,
so this issue does not matter for changing the intel_pstate operation
mode, but it theoretically can cause a crash to occur on CPU device hot
removal (which currently can only happen in virt, but it is formally
supported nevertheless).
Address this issue by modifying update_qos_request() to drop the
reference to the policy later. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix peer HE MCS assignment
In ath11k_wmi_send_peer_assoc_cmd(), peer's transmit MCS is sent to
firmware as receive MCS while peer's receive MCS sent as transmit MCS,
which goes against firmwire's definition.
While connecting to a misbehaved AP that advertises 0xffff (meaning not
supported) for 160 MHz transmit MCS map, firmware crashes due to 0xffff
is assigned to he_mcs->rx_mcs_set field.
Ext Tag: HE Capabilities
[...]
Supported HE-MCS and NSS Set
[...]
Rx and Tx MCS Maps 160 MHz
[...]
Tx HE-MCS Map 160 MHz: 0xffff
Swap the assignment to fix this issue.
As the HE rate control mask is meant to limit our own transmit MCS, it
needs to go via he_mcs->rx_mcs_set field. With the aforementioned swapping
done, change is needed as well to apply it to the peer's receive MCS.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid10: fix memleak of md thread
In raid10_run(), if setup_conf() succeed and raid10_run() failed before
setting 'mddev->thread', then in the error path 'conf->thread' is not
freed.
Fix the problem by setting 'mddev->thread' right after setup_conf(). |
| In the Linux kernel, the following vulnerability has been resolved:
samples/bpf: Fix buffer overflow in tcp_basertt
Using sizeof(nv) or strlen(nv)+1 is correct. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86/amd/pmc: Add support for Van Gogh SoC
The ROG Xbox Ally (non-X) SoC features a similar architecture to the
Steam Deck. While the Steam Deck supports S3 (s2idle causes a crash),
this support was dropped by the Xbox Ally which only S0ix suspend.
Since the handler is missing here, this causes the device to not suspend
and the AMD GPU driver to crash while trying to resume afterwards due to
a power hang. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to avoid migrating empty section
It reports a bug from device w/ zufs:
F2FS-fs (dm-64): Inconsistent segment (173822) type [1, 0] in SSA and SIT
F2FS-fs (dm-64): Stopped filesystem due to reason: 4
Thread A Thread B
- f2fs_expand_inode_data
- f2fs_allocate_pinning_section
- f2fs_gc_range
- do_garbage_collect w/ segno #x
- writepage
- f2fs_allocate_data_block
- new_curseg
- allocate segno #x
The root cause is: fallocate on pinning file may race w/ block allocation
as above, result in do_garbage_collect() from fallocate() may migrate
segment which is just allocated by a log, the log will update segment type
in its in-memory structure, however GC will get segment type from on-disk
SSA block, once segment type changes by log, we can detect such
inconsistency, then shutdown filesystem.
In this case, on-disk SSA shows type of segno #173822 is 1 (SUM_TYPE_NODE),
however segno #173822 was just allocated as data type segment, so in-memory
SIT shows type of segno #173822 is 0 (SUM_TYPE_DATA).
Change as below to fix this issue:
- check whether current section is empty before gc
- add sanity checks on do_garbage_collect() to avoid any race case, result
in migrating segment used by log.
- btw, it fixes misc issue in printed logs: "SSA and SIT" -> "SIT and SSA". |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fortify the spinlock against deadlock by interrupt
In the function ieee80211_tx_dequeue() there is a particular locking
sequence:
begin:
spin_lock(&local->queue_stop_reason_lock);
q_stopped = local->queue_stop_reasons[q];
spin_unlock(&local->queue_stop_reason_lock);
However small the chance (increased by ftracetest), an asynchronous
interrupt can occur in between of spin_lock() and spin_unlock(),
and the interrupt routine will attempt to lock the same
&local->queue_stop_reason_lock again.
This will cause a costly reset of the CPU and the wifi device or an
altogether hang in the single CPU and single core scenario.
The only remaining spin_lock(&local->queue_stop_reason_lock) that
did not disable interrupts was patched, which should prevent any
deadlocks on the same CPU/core and the same wifi device.
This is the probable trace of the deadlock:
kernel: ================================
kernel: WARNING: inconsistent lock state
kernel: 6.3.0-rc6-mt-20230401-00001-gf86822a1170f #4 Tainted: G W
kernel: --------------------------------
kernel: inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
kernel: kworker/5:0/25656 [HC0[0]:SC0[0]:HE1:SE1] takes:
kernel: ffff9d6190779478 (&local->queue_stop_reason_lock){+.?.}-{2:2}, at: return_to_handler+0x0/0x40
kernel: {IN-SOFTIRQ-W} state was registered at:
kernel: lock_acquire+0xc7/0x2d0
kernel: _raw_spin_lock+0x36/0x50
kernel: ieee80211_tx_dequeue+0xb4/0x1330 [mac80211]
kernel: iwl_mvm_mac_itxq_xmit+0xae/0x210 [iwlmvm]
kernel: iwl_mvm_mac_wake_tx_queue+0x2d/0xd0 [iwlmvm]
kernel: ieee80211_queue_skb+0x450/0x730 [mac80211]
kernel: __ieee80211_xmit_fast.constprop.66+0x834/0xa50 [mac80211]
kernel: __ieee80211_subif_start_xmit+0x217/0x530 [mac80211]
kernel: ieee80211_subif_start_xmit+0x60/0x580 [mac80211]
kernel: dev_hard_start_xmit+0xb5/0x260
kernel: __dev_queue_xmit+0xdbe/0x1200
kernel: neigh_resolve_output+0x166/0x260
kernel: ip_finish_output2+0x216/0xb80
kernel: __ip_finish_output+0x2a4/0x4d0
kernel: ip_finish_output+0x2d/0xd0
kernel: ip_output+0x82/0x2b0
kernel: ip_local_out+0xec/0x110
kernel: igmpv3_sendpack+0x5c/0x90
kernel: igmp_ifc_timer_expire+0x26e/0x4e0
kernel: call_timer_fn+0xa5/0x230
kernel: run_timer_softirq+0x27f/0x550
kernel: __do_softirq+0xb4/0x3a4
kernel: irq_exit_rcu+0x9b/0xc0
kernel: sysvec_apic_timer_interrupt+0x80/0xa0
kernel: asm_sysvec_apic_timer_interrupt+0x1f/0x30
kernel: _raw_spin_unlock_irqrestore+0x3f/0x70
kernel: free_to_partial_list+0x3d6/0x590
kernel: __slab_free+0x1b7/0x310
kernel: kmem_cache_free+0x52d/0x550
kernel: putname+0x5d/0x70
kernel: do_sys_openat2+0x1d7/0x310
kernel: do_sys_open+0x51/0x80
kernel: __x64_sys_openat+0x24/0x30
kernel: do_syscall_64+0x5c/0x90
kernel: entry_SYSCALL_64_after_hwframe+0x72/0xdc
kernel: irq event stamp: 5120729
kernel: hardirqs last enabled at (5120729): [<ffffffff9d149936>] trace_graph_return+0xd6/0x120
kernel: hardirqs last disabled at (5120728): [<ffffffff9d149950>] trace_graph_return+0xf0/0x120
kernel: softirqs last enabled at (5069900): [<ffffffff9cf65b60>] return_to_handler+0x0/0x40
kernel: softirqs last disabled at (5067555): [<ffffffff9cf65b60>] return_to_handler+0x0/0x40
kernel:
other info that might help us debug this:
kernel: Possible unsafe locking scenario:
kernel: CPU0
kernel: ----
kernel: lock(&local->queue_stop_reason_lock);
kernel: <Interrupt>
kernel: lock(&local->queue_stop_reason_lock);
kernel:
*** DEADLOCK ***
kernel: 8 locks held by kworker/5:0/25656:
kernel: #0: ffff9d618009d138 ((wq_completion)events_freezable){+.+.}-{0:0}, at: process_one_work+0x1ca/0x530
kernel: #1: ffffb1ef4637fe68 ((work_completion)(&local->restart_work)){+.+.}-{0:0}, at: process_one_work+0x1ce/0x530
kernel: #2: ffffffff9f166548 (rtnl_mutex){+.+.}-{3:3}, at: return_to_handler+0x0/0x40
kernel: #3: ffff9d619
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
media: dvb-usb: m920x: Fix a potential memory leak in m920x_i2c_xfer()
'read' is freed when it is known to be NULL, but not when a read error
occurs.
Revert the logic to avoid a small leak, should a m920x_read() call fail. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: set page extent mapped after read_folio in relocate_one_page
One of the CI runs triggered the following panic
assertion failed: PagePrivate(page) && page->private, in fs/btrfs/subpage.c:229
------------[ cut here ]------------
kernel BUG at fs/btrfs/subpage.c:229!
Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
CPU: 0 PID: 923660 Comm: btrfs Not tainted 6.5.0-rc3+ #1
pstate: 61400005 (nZCv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--)
pc : btrfs_subpage_assert+0xbc/0xf0
lr : btrfs_subpage_assert+0xbc/0xf0
sp : ffff800093213720
x29: ffff800093213720 x28: ffff8000932138b4 x27: 000000000c280000
x26: 00000001b5d00000 x25: 000000000c281000 x24: 000000000c281fff
x23: 0000000000001000 x22: 0000000000000000 x21: ffffff42b95bf880
x20: ffff42b9528e0000 x19: 0000000000001000 x18: ffffffffffffffff
x17: 667274622f736620 x16: 6e69202c65746176 x15: 0000000000000028
x14: 0000000000000003 x13: 00000000002672d7 x12: 0000000000000000
x11: ffffcd3f0ccd9204 x10: ffffcd3f0554ae50 x9 : ffffcd3f0379528c
x8 : ffff800093213428 x7 : 0000000000000000 x6 : ffffcd3f091771e8
x5 : ffff42b97f333948 x4 : 0000000000000000 x3 : 0000000000000000
x2 : 0000000000000000 x1 : ffff42b9556cde80 x0 : 000000000000004f
Call trace:
btrfs_subpage_assert+0xbc/0xf0
btrfs_subpage_set_dirty+0x38/0xa0
btrfs_page_set_dirty+0x58/0x88
relocate_one_page+0x204/0x5f0
relocate_file_extent_cluster+0x11c/0x180
relocate_data_extent+0xd0/0xf8
relocate_block_group+0x3d0/0x4e8
btrfs_relocate_block_group+0x2d8/0x490
btrfs_relocate_chunk+0x54/0x1a8
btrfs_balance+0x7f4/0x1150
btrfs_ioctl+0x10f0/0x20b8
__arm64_sys_ioctl+0x120/0x11d8
invoke_syscall.constprop.0+0x80/0xd8
do_el0_svc+0x6c/0x158
el0_svc+0x50/0x1b0
el0t_64_sync_handler+0x120/0x130
el0t_64_sync+0x194/0x198
Code: 91098021 b0007fa0 91346000 97e9c6d2 (d4210000)
This is the same problem outlined in 17b17fcd6d44 ("btrfs:
set_page_extent_mapped after read_folio in btrfs_cont_expand") , and the
fix is the same. I originally looked for the same pattern elsewhere in
our code, but mistakenly skipped over this code because I saw the page
cache readahead before we set_page_extent_mapped, not realizing that
this was only in the !page case, that we can still end up with a
!uptodate page and then do the btrfs_read_folio further down.
The fix here is the same as the above mentioned patch, move the
set_page_extent_mapped call to after the btrfs_read_folio() block to
make sure that we have the subpage blocksize stuff setup properly before
using the page. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: mtk_eth_soc: fix possible NULL pointer dereference in mtk_hwlro_get_fdir_all()
rule_locs is allocated in ethtool_get_rxnfc and the size is determined by
rule_cnt from user space. So rule_cnt needs to be check before using
rule_locs to avoid NULL pointer dereference. |
