| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: wwan: t7xx: fix potential skb->frags overflow in RX path
When receiving data in the DPMAIF RX path,
the t7xx_dpmaif_set_frag_to_skb() function adds
page fragments to an skb without checking if the number of
fragments has exceeded MAX_SKB_FRAGS. This could lead to a buffer overflow
in skb_shinfo(skb)->frags[] array, corrupting adjacent memory and
potentially causing kernel crashes or other undefined behavior.
This issue was identified through static code analysis by comparing with a
similar vulnerability fixed in the mt76 driver commit b102f0c522cf ("mt76:
fix array overflow on receiving too many fragments for a packet").
The vulnerability could be triggered if the modem firmware sends packets
with excessive fragments. While under normal protocol conditions (MTU 3080
bytes, BAT buffer 3584 bytes),
a single packet should not require additional
fragments, the kernel should not blindly trust firmware behavior.
Malicious, buggy, or compromised firmware could potentially craft packets
with more fragments than the kernel expects.
Fix this by adding a bounds check before calling skb_add_rx_frag() to
ensure nr_frags does not exceed MAX_SKB_FRAGS.
The check must be performed before unmapping to avoid a page leak
and double DMA unmap during device teardown. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: tegra210-quad: Protect curr_xfer check in IRQ handler
Now that all other accesses to curr_xfer are done under the lock,
protect the curr_xfer NULL check in tegra_qspi_isr_thread() with the
spinlock. Without this protection, the following race can occur:
CPU0 (ISR thread) CPU1 (timeout path)
---------------- -------------------
if (!tqspi->curr_xfer)
// sees non-NULL
spin_lock()
tqspi->curr_xfer = NULL
spin_unlock()
handle_*_xfer()
spin_lock()
t = tqspi->curr_xfer // NULL!
... t->len ... // NULL dereference!
With this patch, all curr_xfer accesses are now properly synchronized.
Although all accesses to curr_xfer are done under the lock, in
tegra_qspi_isr_thread() it checks for NULL, releases the lock and
reacquires it later in handle_cpu_based_xfer()/handle_dma_based_xfer().
There is a potential for an update in between, which could cause a NULL
pointer dereference.
To handle this, add a NULL check inside the handlers after acquiring
the lock. This ensures that if the timeout path has already cleared
curr_xfer, the handler will safely return without dereferencing the
NULL pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
bus: fsl-mc: fix use-after-free in driver_override_show()
The driver_override_show() function reads the driver_override string
without holding the device_lock. However, driver_override_store() uses
driver_set_override(), which modifies and frees the string while holding
the device_lock.
This can result in a concurrent use-after-free if the string is freed
by the store function while being read by the show function.
Fix this by holding the device_lock around the read operation. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: add chann_lock to protect ksmbd_chann_list xarray
ksmbd_chann_list xarray lacks synchronization, allowing use-after-free in
multi-channel sessions (between lookup_chann_list() and ksmbd_chann_del).
Adds rw_semaphore chann_lock to struct ksmbd_session and protects
all xa_load/xa_store/xa_erase accesses. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to avoid UAF in f2fs_write_end_io()
As syzbot reported an use-after-free issue in f2fs_write_end_io().
It is caused by below race condition:
loop device umount
- worker_thread
- loop_process_work
- do_req_filebacked
- lo_rw_aio
- lo_rw_aio_complete
- blk_mq_end_request
- blk_update_request
- f2fs_write_end_io
- dec_page_count
- folio_end_writeback
- kill_f2fs_super
- kill_block_super
- f2fs_put_super
: free(sbi)
: get_pages(, F2FS_WB_CP_DATA)
accessed sbi which is freed
In kill_f2fs_super(), we will drop all page caches of f2fs inodes before
call free(sbi), it guarantee that all folios should end its writeback, so
it should be safe to access sbi before last folio_end_writeback().
Let's relocate ckpt thread wakeup flow before folio_end_writeback() to
resolve this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix out-of-bounds access in sysfs attribute read/write
Some f2fs sysfs attributes suffer from out-of-bounds memory access and
incorrect handling of integer values whose size is not 4 bytes.
For example:
vm:~# echo 65537 > /sys/fs/f2fs/vde/carve_out
vm:~# cat /sys/fs/f2fs/vde/carve_out
65537
vm:~# echo 4294967297 > /sys/fs/f2fs/vde/atgc_age_threshold
vm:~# cat /sys/fs/f2fs/vde/atgc_age_threshold
1
carve_out maps to {struct f2fs_sb_info}->carve_out, which is a 8-bit
integer. However, the sysfs interface allows setting it to a value
larger than 255, resulting in an out-of-range update.
atgc_age_threshold maps to {struct atgc_management}->age_threshold,
which is a 64-bit integer, but its sysfs interface cannot correctly set
values larger than UINT_MAX.
The root causes are:
1. __sbi_store() treats all default values as unsigned int, which
prevents updating integers larger than 4 bytes and causes out-of-bounds
writes for integers smaller than 4 bytes.
2. f2fs_sbi_show() also assumes all default values are unsigned int,
leading to out-of-bounds reads and incorrect access to integers larger
than 4 bytes.
This patch introduces {struct f2fs_attr}->size to record the actual size
of the integer associated with each sysfs attribute. With this
information, sysfs read and write operations can correctly access and
update values according to their real data size, avoiding memory
corruption and truncation. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: xilinx: xdma: Fix regmap max_register
The max_register field is assigned the size of the register memory
region instead of the offset of the last register.
The result is that reading from the regmap via debugfs can cause
a segmentation fault:
tail /sys/kernel/debug/regmap/xdma.1.auto/registers
Unable to handle kernel paging request at virtual address ffff800082f70000
Mem abort info:
ESR = 0x0000000096000007
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x07: level 3 translation fault
[...]
Call trace:
regmap_mmio_read32le+0x10/0x30
_regmap_bus_reg_read+0x74/0xc0
_regmap_read+0x68/0x198
regmap_read+0x54/0x88
regmap_read_debugfs+0x140/0x380
regmap_map_read_file+0x30/0x48
full_proxy_read+0x68/0xc8
vfs_read+0xcc/0x310
ksys_read+0x7c/0x120
__arm64_sys_read+0x24/0x40
invoke_syscall.constprop.0+0x64/0x108
do_el0_svc+0xb0/0xd8
el0_svc+0x38/0x130
el0t_64_sync_handler+0x120/0x138
el0t_64_sync+0x194/0x198
Code: aa1e03e9 d503201f f9400000 8b214000 (b9400000)
---[ end trace 0000000000000000 ]---
note: tail[1217] exited with irqs disabled
note: tail[1217] exited with preempt_count 1
Segmentation fault |
| In the Linux kernel, the following vulnerability has been resolved:
net: netpoll: fix incorrect refcount handling causing incorrect cleanup
commit efa95b01da18 ("netpoll: fix use after free") incorrectly
ignored the refcount and prematurely set dev->npinfo to NULL during
netpoll cleanup, leading to improper behavior and memory leaks.
Scenario causing lack of proper cleanup:
1) A netpoll is associated with a NIC (e.g., eth0) and netdev->npinfo is
allocated, and refcnt = 1
- Keep in mind that npinfo is shared among all netpoll instances. In
this case, there is just one.
2) Another netpoll is also associated with the same NIC and
npinfo->refcnt += 1.
- Now dev->npinfo->refcnt = 2;
- There is just one npinfo associated to the netdev.
3) When the first netpolls goes to clean up:
- The first cleanup succeeds and clears np->dev->npinfo, ignoring
refcnt.
- It basically calls `RCU_INIT_POINTER(np->dev->npinfo, NULL);`
- Set dev->npinfo = NULL, without proper cleanup
- No ->ndo_netpoll_cleanup() is either called
4) Now the second target tries to clean up
- The second cleanup fails because np->dev->npinfo is already NULL.
* In this case, ops->ndo_netpoll_cleanup() was never called, and
the skb pool is not cleaned as well (for the second netpoll
instance)
- This leaks npinfo and skbpool skbs, which is clearly reported by
kmemleak.
Revert commit efa95b01da18 ("netpoll: fix use after free") and adds
clarifying comments emphasizing that npinfo cleanup should only happen
once the refcount reaches zero, ensuring stable and correct netpoll
behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
can: gs_usb: gs_usb_receive_bulk_callback(): check actual_length before accessing data
The URB received in gs_usb_receive_bulk_callback() contains a struct
gs_host_frame. The length of the data after the header depends on the
gs_host_frame hf::flags and the active device features (e.g. time
stamping).
Introduce a new function gs_usb_get_minimum_length() and check that we have
at least received the required amount of data before accessing it. Only
copy the data to that skb that has actually been received.
[mkl: rename gs_usb_get_minimum_length() -> +gs_usb_get_minimum_rx_length()] |
| In the Linux kernel, the following vulnerability has been resolved:
md: avoid repeated calls to del_gendisk
There is a uaf problem which is found by case 23rdev-lifetime:
Oops: general protection fault, probably for non-canonical address 0xdead000000000122
RIP: 0010:bdi_unregister+0x4b/0x170
Call Trace:
<TASK>
__del_gendisk+0x356/0x3e0
mddev_unlock+0x351/0x360
rdev_attr_store+0x217/0x280
kernfs_fop_write_iter+0x14a/0x210
vfs_write+0x29e/0x550
ksys_write+0x74/0xf0
do_syscall_64+0xbb/0x380
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7ff5250a177e
The sequence is:
1. rdev remove path gets reconfig_mutex
2. rdev remove path release reconfig_mutex in mddev_unlock
3. md stop calls do_md_stop and sets MD_DELETED
4. rdev remove path calls del_gendisk because MD_DELETED is set
5. md stop path release reconfig_mutex and calls del_gendisk again
So there is a race condition we should resolve. This patch adds a
flag MD_DO_DELETE to avoid the race condition. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86: Fix NULL event access and potential PEBS record loss
When intel_pmu_drain_pebs_icl() is called to drain PEBS records, the
perf_event_overflow() could be called to process the last PEBS record.
While perf_event_overflow() could trigger the interrupt throttle and
stop all events of the group, like what the below call-chain shows.
perf_event_overflow()
-> __perf_event_overflow()
->__perf_event_account_interrupt()
-> perf_event_throttle_group()
-> perf_event_throttle()
-> event->pmu->stop()
-> x86_pmu_stop()
The side effect of stopping the events is that all corresponding event
pointers in cpuc->events[] array are cleared to NULL.
Assume there are two PEBS events (event a and event b) in a group. When
intel_pmu_drain_pebs_icl() calls perf_event_overflow() to process the
last PEBS record of PEBS event a, interrupt throttle is triggered and
all pointers of event a and event b are cleared to NULL. Then
intel_pmu_drain_pebs_icl() tries to process the last PEBS record of
event b and encounters NULL pointer access.
To avoid this issue, move cpuc->events[] clearing from x86_pmu_stop()
to x86_pmu_del(). It's safe since cpuc->active_mask or
cpuc->pebs_enabled is always checked before access the event pointer
from cpuc->events[]. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: bcsp: receive data only if registered
Currently, bcsp_recv() can be called even when the BCSP protocol has not
been registered. This leads to a NULL pointer dereference, as shown in
the following stack trace:
KASAN: null-ptr-deref in range [0x0000000000000108-0x000000000000010f]
RIP: 0010:bcsp_recv+0x13d/0x1740 drivers/bluetooth/hci_bcsp.c:590
Call Trace:
<TASK>
hci_uart_tty_receive+0x194/0x220 drivers/bluetooth/hci_ldisc.c:627
tiocsti+0x23c/0x2c0 drivers/tty/tty_io.c:2290
tty_ioctl+0x626/0xde0 drivers/tty/tty_io.c:2706
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl+0xfc/0x170 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
To prevent this, ensure that the HCI_UART_REGISTERED flag is set before
processing received data. If the protocol is not registered, return
-EUNATCH. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: hda/ca0132: fixup buffer overrun at tuning_ctl_set()
tuning_ctl_set() might have buffer overrun at (X) if it didn't break
from loop by matching (A).
static int tuning_ctl_set(...)
{
for (i = 0; i < TUNING_CTLS_COUNT; i++)
(A) if (nid == ca0132_tuning_ctls[i].nid)
break;
snd_hda_power_up(...);
(X) dspio_set_param(..., ca0132_tuning_ctls[i].mid, ...);
snd_hda_power_down(...); ^
return 1;
}
We will get below error by cppcheck
sound/pci/hda/patch_ca0132.c:4229:2: note: After for loop, i has value 12
for (i = 0; i < TUNING_CTLS_COUNT; i++)
^
sound/pci/hda/patch_ca0132.c:4234:43: note: Array index out of bounds
dspio_set_param(codec, ca0132_tuning_ctls[i].mid, 0x20,
^
This patch cares non match case. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: cdns3: gadget: Use-after-free during failed initialization and exit of cdnsp gadget
In the __cdnsp_gadget_init() and cdnsp_gadget_exit() functions, the gadget
structure (pdev->gadget) was freed before its endpoints.
The endpoints are linked via the ep_list in the gadget structure.
Freeing the gadget first leaves dangling pointers in the endpoint list.
When the endpoints are subsequently freed, this results in a use-after-free.
Fix:
By separating the usb_del_gadget_udc() operation into distinct "del" and
"put" steps, cdnsp_gadget_free_endpoints() can be executed prior to the
final release of the gadget structure with usb_put_gadget().
A patch similar to bb9c74a5bd14("usb: dwc3: gadget: Free gadget structure
only after freeing endpoints"). |
| In the Linux kernel, the following vulnerability has been resolved:
cpufreq: intel_pstate: Fix object lifecycle issue in update_qos_request()
The cpufreq_cpu_put() call in update_qos_request() takes place too early
because the latter subsequently calls freq_qos_update_request() that
indirectly accesses the policy object in question through the QoS request
object passed to it.
Fortunately, update_qos_request() is called under intel_pstate_driver_lock,
so this issue does not matter for changing the intel_pstate operation
mode, but it theoretically can cause a crash to occur on CPU device hot
removal (which currently can only happen in virt, but it is formally
supported nevertheless).
Address this issue by modifying update_qos_request() to drop the
reference to the policy later. |
| In the Linux kernel, the following vulnerability has been resolved:
mailbox: zynqmp-ipi: Fix out-of-bounds access in mailbox cleanup loop
The cleanup loop was starting at the wrong array index, causing
out-of-bounds access.
Start the loop at the correct index for zero-indexed arrays to prevent
accessing memory beyond the allocated array bounds. |
| In the Linux kernel, the following vulnerability has been resolved:
arch_topology: Fix incorrect error check in topology_parse_cpu_capacity()
Fix incorrect use of PTR_ERR_OR_ZERO() in topology_parse_cpu_capacity()
which causes the code to proceed with NULL clock pointers. The current
logic uses !PTR_ERR_OR_ZERO(cpu_clk) which evaluates to true for both
valid pointers and NULL, leading to potential NULL pointer dereference
in clk_get_rate().
Per include/linux/err.h documentation, PTR_ERR_OR_ZERO(ptr) returns:
"The error code within @ptr if it is an error pointer; 0 otherwise."
This means PTR_ERR_OR_ZERO() returns 0 for both valid pointers AND NULL
pointers. Therefore !PTR_ERR_OR_ZERO(cpu_clk) evaluates to true (proceed)
when cpu_clk is either valid or NULL, causing clk_get_rate(NULL) to be
called when of_clk_get() returns NULL.
Replace with !IS_ERR_OR_NULL(cpu_clk) which only proceeds for valid
pointers, preventing potential NULL pointer dereference in clk_get_rate(). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: Fix memory leak in vmw_mksstat_add_ioctl()
If the copy of the description string from userspace fails, then the page
for the instance descriptor doesn't get freed before returning -EFAULT,
which leads to a memleak. |
| In the Linux kernel, the following vulnerability has been resolved:
RISC-V: KVM: Write hgatp register with valid mode bits
According to the RISC-V Privileged Architecture Spec, when MODE=Bare
is selected,software must write zero to the remaining fields of hgatp.
We have detected the valid mode supported by the HW before, So using a
valid mode to detect how many vmid bits are supported. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Cap MSIX used to online CPUs + 1
The irdma driver can use a maximum number of msix vectors equal
to num_online_cpus() + 1 and the kernel warning stack below is shown
if that number is exceeded.
The kernel throws a warning as the driver tries to update the affinity
hint with a CPU mask greater than the max CPU IDs. Fix this by capping
the MSIX vectors to num_online_cpus() + 1.
WARNING: CPU: 7 PID: 23655 at include/linux/cpumask.h:106 irdma_cfg_ceq_vector+0x34c/0x3f0 [irdma]
RIP: 0010:irdma_cfg_ceq_vector+0x34c/0x3f0 [irdma]
Call Trace:
irdma_rt_init_hw+0xa62/0x1290 [irdma]
? irdma_alloc_local_mac_entry+0x1a0/0x1a0 [irdma]
? __is_kernel_percpu_address+0x63/0x310
? rcu_read_lock_held_common+0xe/0xb0
? irdma_lan_unregister_qset+0x280/0x280 [irdma]
? irdma_request_reset+0x80/0x80 [irdma]
? ice_get_qos_params+0x84/0x390 [ice]
irdma_probe+0xa40/0xfc0 [irdma]
? rcu_read_lock_bh_held+0xd0/0xd0
? irdma_remove+0x140/0x140 [irdma]
? rcu_read_lock_sched_held+0x62/0xe0
? down_write+0x187/0x3d0
? auxiliary_match_id+0xf0/0x1a0
? irdma_remove+0x140/0x140 [irdma]
auxiliary_bus_probe+0xa6/0x100
__driver_probe_device+0x4a4/0xd50
? __device_attach_driver+0x2c0/0x2c0
driver_probe_device+0x4a/0x110
__driver_attach+0x1aa/0x350
bus_for_each_dev+0x11d/0x1b0
? subsys_dev_iter_init+0xe0/0xe0
bus_add_driver+0x3b1/0x610
driver_register+0x18e/0x410
? 0xffffffffc0b88000
irdma_init_module+0x50/0xaa [irdma]
do_one_initcall+0x103/0x5f0
? perf_trace_initcall_level+0x420/0x420
? do_init_module+0x4e/0x700
? __kasan_kmalloc+0x7d/0xa0
? kmem_cache_alloc_trace+0x188/0x2b0
? kasan_unpoison+0x21/0x50
do_init_module+0x1d1/0x700
load_module+0x3867/0x5260
? layout_and_allocate+0x3990/0x3990
? rcu_read_lock_held_common+0xe/0xb0
? rcu_read_lock_sched_held+0x62/0xe0
? rcu_read_lock_bh_held+0xd0/0xd0
? __vmalloc_node_range+0x46b/0x890
? lock_release+0x5c8/0xba0
? alloc_vm_area+0x120/0x120
? selinux_kernel_module_from_file+0x2a5/0x300
? __inode_security_revalidate+0xf0/0xf0
? __do_sys_init_module+0x1db/0x260
__do_sys_init_module+0x1db/0x260
? load_module+0x5260/0x5260
? do_syscall_64+0x22/0x450
do_syscall_64+0xa5/0x450
entry_SYSCALL_64_after_hwframe+0x66/0xdb |
