| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: avoid uninit memory read in ath9k_htc_rx_msg()
syzbot is reporting uninit value at ath9k_htc_rx_msg() [1], for
ioctl(USB_RAW_IOCTL_EP_WRITE) can call ath9k_hif_usb_rx_stream() with
pkt_len = 0 but ath9k_hif_usb_rx_stream() uses
__dev_alloc_skb(pkt_len + 32, GFP_ATOMIC) based on an assumption that
pkt_len is valid. As a result, ath9k_hif_usb_rx_stream() allocates skb
with uninitialized memory and ath9k_htc_rx_msg() is reading from
uninitialized memory.
Since bytes accessed by ath9k_htc_rx_msg() is not known until
ath9k_htc_rx_msg() is called, it would be difficult to check minimal valid
pkt_len at "if (pkt_len > 2 * MAX_RX_BUF_SIZE) {" line in
ath9k_hif_usb_rx_stream().
We have two choices. One is to workaround by adding __GFP_ZERO so that
ath9k_htc_rx_msg() sees 0 if pkt_len is invalid. The other is to let
ath9k_htc_rx_msg() validate pkt_len before accessing. This patch chose
the latter.
Note that I'm not sure threshold condition is correct, for I can't find
details on possible packet length used by this protocol. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921e: fix rmmod crash in driver reload test
In insmod/rmmod stress test, the following crash dump shows up immediately.
The problem is caused by missing mt76_dev in mt7921_pci_remove(). We
should make sure the drvdata is ready before probe() finished.
[168.862789] ==================================================================
[168.862797] BUG: KASAN: user-memory-access in try_to_grab_pending+0x59/0x480
[168.862805] Write of size 8 at addr 0000000000006df0 by task rmmod/5361
[168.862812] CPU: 7 PID: 5361 Comm: rmmod Tainted: G OE 5.19.0-rc6 #1
[168.862816] Hardware name: Intel(R) Client Systems NUC8i7BEH/NUC8BEB, 05/04/2020
[168.862820] Call Trace:
[168.862822] <TASK>
[168.862825] dump_stack_lvl+0x49/0x63
[168.862832] print_report.cold+0x493/0x6b7
[168.862845] kasan_report+0xa7/0x120
[168.862857] kasan_check_range+0x163/0x200
[168.862861] __kasan_check_write+0x14/0x20
[168.862866] try_to_grab_pending+0x59/0x480
[168.862870] __cancel_work_timer+0xbb/0x340
[168.862898] cancel_work_sync+0x10/0x20
[168.862902] mt7921_pci_remove+0x61/0x1c0 [mt7921e]
[168.862909] pci_device_remove+0xa3/0x1d0
[168.862914] device_remove+0xc4/0x170
[168.862920] device_release_driver_internal+0x163/0x300
[168.862925] driver_detach+0xc7/0x1a0
[168.862930] bus_remove_driver+0xeb/0x2d0
[168.862935] driver_unregister+0x71/0xb0
[168.862939] pci_unregister_driver+0x30/0x230
[168.862944] mt7921_pci_driver_exit+0x10/0x1b [mt7921e]
[168.862949] __x64_sys_delete_module+0x2f9/0x4b0
[168.862968] do_syscall_64+0x38/0x90
[168.862973] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Test steps:
1. insmode
2. do not ifup
3. rmmod quickly (within 1 second) |
| In the Linux kernel, the following vulnerability has been resolved:
x86/apic: Don't disable x2APIC if locked
The APIC supports two modes, legacy APIC (or xAPIC), and Extended APIC
(or x2APIC). X2APIC mode is mostly compatible with legacy APIC, but
it disables the memory-mapped APIC interface in favor of one that uses
MSRs. The APIC mode is controlled by the EXT bit in the APIC MSR.
The MMIO/xAPIC interface has some problems, most notably the APIC LEAK
[1]. This bug allows an attacker to use the APIC MMIO interface to
extract data from the SGX enclave.
Introduce support for a new feature that will allow the BIOS to lock
the APIC in x2APIC mode. If the APIC is locked in x2APIC mode and the
kernel tries to disable the APIC or revert to legacy APIC mode a GP
fault will occur.
Introduce support for a new MSR (IA32_XAPIC_DISABLE_STATUS) and handle
the new locked mode when the LEGACY_XAPIC_DISABLED bit is set by
preventing the kernel from trying to disable the x2APIC.
On platforms with the IA32_XAPIC_DISABLE_STATUS MSR, if SGX or TDX are
enabled the LEGACY_XAPIC_DISABLED will be set by the BIOS. If
legacy APIC is required, then it SGX and TDX need to be disabled in the
BIOS.
[1]: https://aepicleak.com/aepicleak.pdf |
| In the Linux kernel, the following vulnerability has been resolved:
media: ipu3-imgu: Fix NULL pointer dereference in active selection access
What the IMGU driver did was that it first acquired the pointers to active
and try V4L2 subdev state, and only then figured out which one to use.
The problem with that approach and a later patch (see Fixes: tag) is that
as sd_state argument to v4l2_subdev_get_try_crop() et al is NULL, there is
now an attempt to dereference that.
Fix this.
Also rewrap lines a little. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: core: fix resource leak in regulator_register()
I got some resource leak reports while doing fault injection test:
OF: ERROR: memory leak, expected refcount 1 instead of 100,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /i2c/pmic@64/regulators/buck1
unreferenced object 0xffff88810deea000 (size 512):
comm "490-i2c-rt5190a", pid 253, jiffies 4294859840 (age 5061.046s)
hex dump (first 32 bytes):
00 00 00 00 ad 4e ad de ff ff ff ff 00 00 00 00 .....N..........
ff ff ff ff ff ff ff ff a0 1e 00 a1 ff ff ff ff ................
backtrace:
[<00000000d78541e2>] kmalloc_trace+0x21/0x110
[<00000000b343d153>] device_private_init+0x32/0xd0
[<00000000be1f0c70>] device_add+0xb2d/0x1030
[<00000000e3e6344d>] regulator_register+0xaf2/0x12a0
[<00000000e2f5e754>] devm_regulator_register+0x57/0xb0
[<000000008b898197>] rt5190a_probe+0x52a/0x861 [rt5190a_regulator]
unreferenced object 0xffff88810b617b80 (size 32):
comm "490-i2c-rt5190a", pid 253, jiffies 4294859904 (age 5060.983s)
hex dump (first 32 bytes):
72 65 67 75 6c 61 74 6f 72 2e 32 38 36 38 2d 53 regulator.2868-S
55 50 50 4c 59 00 ff ff 29 00 00 00 2b 00 00 00 UPPLY...)...+...
backtrace:
[<000000009da9280d>] __kmalloc_node_track_caller+0x44/0x1b0
[<0000000025c6a4e5>] kstrdup+0x3a/0x70
[<00000000790efb69>] create_regulator+0xc0/0x4e0
[<0000000005ed203a>] regulator_resolve_supply+0x2d4/0x440
[<0000000045796214>] regulator_register+0x10b3/0x12a0
[<00000000e2f5e754>] devm_regulator_register+0x57/0xb0
[<000000008b898197>] rt5190a_probe+0x52a/0x861 [rt5190a_regulator]
After calling regulator_resolve_supply(), the 'rdev->supply' is set
by set_supply(), after this set, in the error path, the resources
need be released, so call regulator_put() to avoid the leaks. |
| In the Linux kernel, the following vulnerability has been resolved:
media: vidtv: Fix use-after-free in vidtv_bridge_dvb_init()
KASAN reports a use-after-free:
BUG: KASAN: use-after-free in dvb_dmxdev_release+0x4d5/0x5d0 [dvb_core]
Call Trace:
...
dvb_dmxdev_release+0x4d5/0x5d0 [dvb_core]
vidtv_bridge_probe+0x7bf/0xa40 [dvb_vidtv_bridge]
platform_probe+0xb6/0x170
...
Allocated by task 1238:
...
dvb_register_device+0x1a7/0xa70 [dvb_core]
dvb_dmxdev_init+0x2af/0x4a0 [dvb_core]
vidtv_bridge_probe+0x766/0xa40 [dvb_vidtv_bridge]
...
Freed by task 1238:
dvb_register_device+0x6d2/0xa70 [dvb_core]
dvb_dmxdev_init+0x2af/0x4a0 [dvb_core]
vidtv_bridge_probe+0x766/0xa40 [dvb_vidtv_bridge]
...
It is because the error handling in vidtv_bridge_dvb_init() is wrong.
First, vidtv_bridge_dmx(dev)_init() will clean themselves when fail, but
goto fail_dmx(_dev): calls release functions again, which causes
use-after-free.
Also, in fail_fe, fail_tuner_probe and fail_demod_probe, j = i will cause
out-of-bound when i finished its loop (i == NUM_FE). And the loop
releasing is wrong, although now NUM_FE is 1 so it won't cause problem.
Fix this by correctly releasing everything. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/lcs: Fix return type of lcs_start_xmit()
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/lcs.c:2090:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = lcs_start_xmit,
^~~~~~~~~~~~~~
drivers/s390/net/lcs.c:2097:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = lcs_start_xmit,
^~~~~~~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of lcs_start_xmit() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: silence the warning when evicting inode with dioread_nolock
When evicting an inode with default dioread_nolock, it could be raced by
the unwritten extents converting kworker after writeback some new
allocated dirty blocks. It convert unwritten extents to written, the
extents could be merged to upper level and free extent blocks, so it
could mark the inode dirty again even this inode has been marked
I_FREEING. But the inode->i_io_list check and warning in
ext4_evict_inode() missing this corner case. Fortunately,
ext4_evict_inode() will wait all extents converting finished before this
check, so it will not lead to inode use-after-free problem, every thing
is OK besides this warning. The WARN_ON_ONCE was originally designed
for finding inode use-after-free issues in advance, but if we add
current dioread_nolock case in, it will become not quite useful, so fix
this warning by just remove this check.
======
WARNING: CPU: 7 PID: 1092 at fs/ext4/inode.c:227
ext4_evict_inode+0x875/0xc60
...
RIP: 0010:ext4_evict_inode+0x875/0xc60
...
Call Trace:
<TASK>
evict+0x11c/0x2b0
iput+0x236/0x3a0
do_unlinkat+0x1b4/0x490
__x64_sys_unlinkat+0x4c/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7fa933c1115b
======
rm kworker
ext4_end_io_end()
vfs_unlink()
ext4_unlink()
ext4_convert_unwritten_io_end_vec()
ext4_convert_unwritten_extents()
ext4_map_blocks()
ext4_ext_map_blocks()
ext4_ext_try_to_merge_up()
__mark_inode_dirty()
check !I_FREEING
locked_inode_to_wb_and_lock_list()
iput()
iput_final()
evict()
ext4_evict_inode()
truncate_inode_pages_final() //wait release io_end
inode_io_list_move_locked()
ext4_release_io_end()
trigger WARN_ON_ONCE() |
| In the Linux kernel, the following vulnerability has been resolved:
usb: idmouse: fix an uninit-value in idmouse_open
In idmouse_create_image, if any ftip_command fails, it will
go to the reset label. However, this leads to the data in
bulk_in_buffer[HEADER..IMGSIZE] uninitialized. And the check
for valid image incurs an uninitialized dereference.
Fix this by moving the check before reset label since this
check only be valid if the data after bulk_in_buffer[HEADER]
has concrete data.
Note that this is found by KMSAN, so only kernel compilation
is tested. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: do not run mt76u_status_worker if the device is not running
Fix the following NULL pointer dereference avoiding to run
mt76u_status_worker thread if the device is not running yet.
KASAN: null-ptr-deref in range
[0x0000000000000000-0x0000000000000007]
CPU: 0 PID: 98 Comm: kworker/u2:2 Not tainted 5.14.0+ #78 Hardware
name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Workqueue: mt76 mt76u_tx_status_data
RIP: 0010:mt76x02_mac_fill_tx_status.isra.0+0x82c/0x9e0
Code: c5 48 b8 00 00 00 00 00 fc ff df 80 3c 02 00 0f 85 94 01 00 00
48 b8 00 00 00 00 00 fc ff df 4d 8b 34 24 4c 89 f2 48 c1 ea 03 <0f>
b6
04 02 84 c0 74 08 3c 03 0f 8e 89 01 00 00 41 8b 16 41 0f b7
RSP: 0018:ffffc900005af988 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffffc900005afae8 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff832fc661 RDI: ffffc900005afc2a
RBP: ffffc900005afae0 R08: 0000000000000001 R09: fffff520000b5f3c
R10: 0000000000000003 R11: fffff520000b5f3b R12: ffff88810b6132d8
R13: 000000000000ffff R14: 0000000000000000 R15: ffffc900005afc28
FS: 0000000000000000(0000) GS:ffff88811aa00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa0eda6a000 CR3: 0000000118f17000 CR4: 0000000000750ef0
PKRU: 55555554
Call Trace:
mt76x02_send_tx_status+0x1d2/0xeb0
mt76x02_tx_status_data+0x8e/0xd0
mt76u_tx_status_data+0xe1/0x240
process_one_work+0x92b/0x1460
worker_thread+0x95/0xe00
kthread+0x3a1/0x480
ret_from_fork+0x1f/0x30
Modules linked in:
--[ end trace 8df5d20fc5040f65 ]--
RIP: 0010:mt76x02_mac_fill_tx_status.isra.0+0x82c/0x9e0
Code: c5 48 b8 00 00 00 00 00 fc ff df 80 3c 02 00 0f 85 94 01 00 00
48 b8 00 00 00 00 00 fc ff df 4d 8b 34 24 4c 89 f2 48 c1 ea 03 <0f>
b6
04 02 84 c0 74 08 3c 03 0f 8e 89 01 00 00 41 8b 16 41 0f b7
RSP: 0018:ffffc900005af988 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffffc900005afae8 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff832fc661 RDI: ffffc900005afc2a
RBP: ffffc900005afae0 R08: 0000000000000001 R09: fffff520000b5f3c
R10: 0000000000000003 R11: fffff520000b5f3b R12: ffff88810b6132d8
R13: 000000000000ffff R14: 0000000000000000 R15: ffffc900005afc28
FS: 0000000000000000(0000) GS:ffff88811aa00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa0eda6a000 CR3: 0000000118f17000 CR4: 0000000000750ef0
PKRU: 55555554
Moreover move stat_work schedule out of the for loop. |
| In the Linux kernel, the following vulnerability has been resolved:
vhost-vdpa: fix an iotlb memory leak
Before commit 3d5698793897 ("vhost-vdpa: introduce asid based IOTLB")
we called vhost_vdpa_iotlb_unmap(v, iotlb, 0ULL, 0ULL - 1) during
release to free all the resources allocated when processing user IOTLB
messages through vhost_vdpa_process_iotlb_update().
That commit changed the handling of IOTLB a bit, and we accidentally
removed some code called during the release.
We partially fixed this with commit 037d4305569a ("vhost-vdpa: call
vhost_vdpa_cleanup during the release") but a potential memory leak is
still there as showed by kmemleak if the application does not send
VHOST_IOTLB_INVALIDATE or crashes:
unreferenced object 0xffff888007fbaa30 (size 16):
comm "blkio-bench", pid 914, jiffies 4294993521 (age 885.500s)
hex dump (first 16 bytes):
40 73 41 07 80 88 ff ff 00 00 00 00 00 00 00 00 @sA.............
backtrace:
[<0000000087736d2a>] kmem_cache_alloc_trace+0x142/0x1c0
[<0000000060740f50>] vhost_vdpa_process_iotlb_msg+0x68c/0x901 [vhost_vdpa]
[<0000000083e8e205>] vhost_chr_write_iter+0xc0/0x4a0 [vhost]
[<000000008f2f414a>] vhost_vdpa_chr_write_iter+0x18/0x20 [vhost_vdpa]
[<00000000de1cd4a0>] vfs_write+0x216/0x4b0
[<00000000a2850200>] ksys_write+0x71/0xf0
[<00000000de8e720b>] __x64_sys_write+0x19/0x20
[<0000000018b12cbb>] do_syscall_64+0x3f/0x90
[<00000000986ec465>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Let's fix this calling vhost_vdpa_iotlb_unmap() on the whole range in
vhost_vdpa_remove_as(). We move that call before vhost_dev_cleanup()
since we need a valid v->vdev.mm in vhost_vdpa_pa_unmap().
vhost_iotlb_reset() call can be removed, since vhost_vdpa_iotlb_unmap()
on the whole range removes all the entries.
The kmemleak log reported was observed with a vDPA device that has `use_va`
set to true (e.g. VDUSE). This patch has been tested with both types of
devices. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: hif_usb: fix memory leak of urbs in ath9k_hif_usb_dealloc_tx_urbs()
Syzkaller reports a long-known leak of urbs in
ath9k_hif_usb_dealloc_tx_urbs().
The cause of the leak is that usb_get_urb() is called but usb_free_urb()
(or usb_put_urb()) is not called inside usb_kill_urb() as urb->dev or
urb->ep fields have not been initialized and usb_kill_urb() returns
immediately.
The patch removes trying to kill urbs located in hif_dev->tx.tx_buf
because hif_dev->tx.tx_buf is not supposed to contain urbs which are in
pending state (the pending urbs are stored in hif_dev->tx.tx_pending).
The tx.tx_lock is acquired so there should not be any changes in the list.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: Fix pcluster memleak when its block address is zero
syzkaller reported a memleak:
https://syzkaller.appspot.com/bug?id=62f37ff612f0021641eda5b17f056f1668aa9aed
unreferenced object 0xffff88811009c7f8 (size 136):
...
backtrace:
[<ffffffff821db19b>] z_erofs_do_read_page+0x99b/0x1740
[<ffffffff821dee9e>] z_erofs_readahead+0x24e/0x580
[<ffffffff814bc0d6>] read_pages+0x86/0x3d0
...
syzkaller constructed a case: in z_erofs_register_pcluster(),
ztailpacking = false and map->m_pa = zero. This makes pcl->obj.index be
zero although pcl is not a inline pcluster.
Then following path adds refcount for grp, but the refcount won't be put
because pcl is inline.
z_erofs_readahead()
z_erofs_do_read_page() # for another page
z_erofs_collector_begin()
erofs_find_workgroup()
erofs_workgroup_get()
Since it's illegal for the block address of a non-inlined pcluster to
be zero, add check here to avoid registering the pcluster which would
be leaked. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs3: fix uninit memory after failed mi_read in mi_format_new
Fix a KMSAN un-init bug found by syzkaller.
ntfs_get_bh() expects a buffer from sb_getblk(), that buffer may not be
uptodate. We do not bring the buffer uptodate before setting it as
uptodate. If the buffer were to not be uptodate, it could mean adding a
buffer with un-init data to the mi record. Attempting to load that record
will trigger KMSAN.
Avoid this by setting the buffer as uptodate, if it’s not already, by
overwriting it. |
| In the Linux kernel, the following vulnerability has been resolved:
configfs: fix possible memory leak in configfs_create_dir()
kmemleak reported memory leaks in configfs_create_dir():
unreferenced object 0xffff888009f6af00 (size 192):
comm "modprobe", pid 3777, jiffies 4295537735 (age 233.784s)
backtrace:
kmem_cache_alloc (mm/slub.c:3250 mm/slub.c:3256 mm/slub.c:3263 mm/slub.c:3273)
new_fragment (./include/linux/slab.h:600 fs/configfs/dir.c:163)
configfs_register_subsystem (fs/configfs/dir.c:1857)
basic_write (drivers/hwtracing/stm/p_basic.c:14) stm_p_basic
do_one_initcall (init/main.c:1296)
do_init_module (kernel/module/main.c:2455)
...
unreferenced object 0xffff888003ba7180 (size 96):
comm "modprobe", pid 3777, jiffies 4295537735 (age 233.784s)
backtrace:
kmem_cache_alloc (mm/slub.c:3250 mm/slub.c:3256 mm/slub.c:3263 mm/slub.c:3273)
configfs_new_dirent (./include/linux/slab.h:723 fs/configfs/dir.c:194)
configfs_make_dirent (fs/configfs/dir.c:248)
configfs_create_dir (fs/configfs/dir.c:296)
configfs_attach_group.isra.28 (fs/configfs/dir.c:816 fs/configfs/dir.c:852)
configfs_register_subsystem (fs/configfs/dir.c:1881)
basic_write (drivers/hwtracing/stm/p_basic.c:14) stm_p_basic
do_one_initcall (init/main.c:1296)
do_init_module (kernel/module/main.c:2455)
...
This is because the refcount is not correct in configfs_make_dirent().
For normal stage, the refcount is changing as:
configfs_register_subsystem()
configfs_create_dir()
configfs_make_dirent()
configfs_new_dirent() # set s_count = 1
dentry->d_fsdata = configfs_get(sd); # s_count = 2
...
configfs_unregister_subsystem()
configfs_remove_dir()
remove_dir()
configfs_remove_dirent() # s_count = 1
dput() ...
*dentry_unlink_inode()*
configfs_d_iput() # s_count = 0, release
However, if we failed in configfs_create():
configfs_register_subsystem()
configfs_create_dir()
configfs_make_dirent() # s_count = 2
...
configfs_create() # fail
->out_remove:
configfs_remove_dirent(dentry)
configfs_put(sd) # s_count = 1
return PTR_ERR(inode);
There is no inode in the error path, so the configfs_d_iput() is lost
and makes sd and fragment memory leaked.
To fix this, when we failed in configfs_create(), manually call
configfs_put(sd) to keep the refcount correct. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix peer HE MCS assignment
In ath11k_wmi_send_peer_assoc_cmd(), peer's transmit MCS is sent to
firmware as receive MCS while peer's receive MCS sent as transmit MCS,
which goes against firmwire's definition.
While connecting to a misbehaved AP that advertises 0xffff (meaning not
supported) for 160 MHz transmit MCS map, firmware crashes due to 0xffff
is assigned to he_mcs->rx_mcs_set field.
Ext Tag: HE Capabilities
[...]
Supported HE-MCS and NSS Set
[...]
Rx and Tx MCS Maps 160 MHz
[...]
Tx HE-MCS Map 160 MHz: 0xffff
Swap the assignment to fix this issue.
As the HE rate control mask is meant to limit our own transmit MCS, it
needs to go via he_mcs->rx_mcs_set field. With the aforementioned swapping
done, change is needed as well to apply it to the peer's receive MCS.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix stackmap overflow check in __bpf_get_stackid()
Syzkaller reported a KASAN slab-out-of-bounds write in __bpf_get_stackid()
when copying stack trace data. The issue occurs when the perf trace
contains more stack entries than the stack map bucket can hold,
leading to an out-of-bounds write in the bucket's data array. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Fix PCI device refcount leak in amdgpu_atrm_get_bios()
As comment of pci_get_class() says, it returns a pci_device with its
refcount increased and decreased the refcount for the input parameter
@from if it is not NULL.
If we break the loop in amdgpu_atrm_get_bios() with 'pdev' not NULL, we
need to call pci_dev_put() to decrease the refcount. Add the missing
pci_dev_put() to avoid refcount leak. |
| In the Linux kernel, the following vulnerability has been resolved:
RISC-V: kexec: Fix memory leak of elf header buffer
This is reported by kmemleak detector:
unreferenced object 0xff2000000403d000 (size 4096):
comm "kexec", pid 146, jiffies 4294900633 (age 64.792s)
hex dump (first 32 bytes):
7f 45 4c 46 02 01 01 00 00 00 00 00 00 00 00 00 .ELF............
04 00 f3 00 01 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000566ca97c>] kmemleak_vmalloc+0x3c/0xbe
[<00000000979283d8>] __vmalloc_node_range+0x3ac/0x560
[<00000000b4b3712a>] __vmalloc_node+0x56/0x62
[<00000000854f75e2>] vzalloc+0x2c/0x34
[<00000000e9a00db9>] crash_prepare_elf64_headers+0x80/0x30c
[<0000000067e8bf48>] elf_kexec_load+0x3e8/0x4ec
[<0000000036548e09>] kexec_image_load_default+0x40/0x4c
[<0000000079fbe1b4>] sys_kexec_file_load+0x1c4/0x322
[<0000000040c62c03>] ret_from_syscall+0x0/0x2
In elf_kexec_load(), a buffer is allocated via vzalloc() to store elf
headers. While it's not freed back to system when kdump kernel is
reloaded or unloaded, or when image->elf_header is successfully set and
then fails to load kdump kernel for some reason. Fix it by freeing the
buffer in arch_kimage_file_post_load_cleanup(). |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: set generation before calling btrfs_clean_tree_block in btrfs_init_new_buffer
syzbot is reporting uninit-value in btrfs_clean_tree_block() [1], for
commit bc877d285ca3dba2 ("btrfs: Deduplicate extent_buffer init code")
missed that btrfs_set_header_generation() in btrfs_init_new_buffer() must
not be moved to after clean_tree_block() because clean_tree_block() is
calling btrfs_header_generation() since commit 55c69072d6bd5be1 ("Btrfs:
Fix extent_buffer usage when nodesize != leafsize").
Since memzero_extent_buffer() will reset "struct btrfs_header" part, we
can't move btrfs_set_header_generation() to before memzero_extent_buffer().
Just re-add btrfs_set_header_generation() before btrfs_clean_tree_block(). |
