| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
mmc: vub300: fix NULL-deref on disconnect
Make sure to deregister the controller before dropping the reference to
the driver data on disconnect to avoid NULL-pointer dereferences or
use-after-free. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: Add HID_CLAIMED_INPUT guards in raw_event callbacks missing them
In commit 2ff5baa9b527 ("HID: appleir: Fix potential NULL dereference at
raw event handle"), we handle the fact that raw event callbacks
can happen even for a HID device that has not been "claimed" causing a
crash if a broken device were attempted to be connected to the system.
Fix up the remaining in-tree HID drivers that forgot to add this same
check to resolve the same issue. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bridge: fix nd_tbl NULL dereference when IPv6 is disabled
When booting with the 'ipv6.disable=1' parameter, the nd_tbl is never
initialized because inet6_init() exits before ndisc_init() is called
which initializes it. Then, if neigh_suppress is enabled and an ICMPv6
Neighbor Discovery packet reaches the bridge, br_do_suppress_nd() will
dereference ipv6_stub->nd_tbl which is NULL, passing it to
neigh_lookup(). This causes a kernel NULL pointer dereference.
BUG: kernel NULL pointer dereference, address: 0000000000000268
Oops: 0000 [#1] PREEMPT SMP NOPTI
[...]
RIP: 0010:neigh_lookup+0x16/0xe0
[...]
Call Trace:
<IRQ>
? neigh_lookup+0x16/0xe0
br_do_suppress_nd+0x160/0x290 [bridge]
br_handle_frame_finish+0x500/0x620 [bridge]
br_handle_frame+0x353/0x440 [bridge]
__netif_receive_skb_core.constprop.0+0x298/0x1110
__netif_receive_skb_one_core+0x3d/0xa0
process_backlog+0xa0/0x140
__napi_poll+0x2c/0x170
net_rx_action+0x2c4/0x3a0
handle_softirqs+0xd0/0x270
do_softirq+0x3f/0x60
Fix this by replacing IS_ENABLED(IPV6) call with ipv6_mod_enabled() in
the callers. This is in essence disabling NS/NA suppression when IPv6 is
disabled. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: i801: Revert "i2c: i801: replace acpi_lock with I2C bus lock"
This reverts commit f707d6b9e7c18f669adfdb443906d46cfbaaa0c1.
Under rare circumstances, multiple udev threads can collect i801 device
info on boot and walk i801_acpi_io_handler somewhat concurrently. The
first will note the area is reserved by acpi to prevent further touches.
This ultimately causes the area to be deregistered. The second will
enter i801_acpi_io_handler after the area is unregistered but before a
check can be made that the area is unregistered. i2c_lock_bus relies on
the now unregistered area containing lock_ops to lock the bus. The end
result is a kernel panic on boot with the following backtrace;
[ 14.971872] ioatdma 0000:09:00.2: enabling device (0100 -> 0102)
[ 14.971873] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 14.971880] #PF: supervisor read access in kernel mode
[ 14.971884] #PF: error_code(0x0000) - not-present page
[ 14.971887] PGD 0 P4D 0
[ 14.971894] Oops: 0000 [#1] PREEMPT SMP PTI
[ 14.971900] CPU: 5 PID: 956 Comm: systemd-udevd Not tainted 5.14.0-611.5.1.el9_7.x86_64 #1
[ 14.971905] Hardware name: XXXXXXXXXXXXXXXXXXXXXXX BIOS 1.20.10.SV91 01/30/2023
[ 14.971908] RIP: 0010:i801_acpi_io_handler+0x2d/0xb0 [i2c_i801]
[ 14.971929] Code: 00 00 49 8b 40 20 41 57 41 56 4d 8b b8 30 04 00 00 49 89 ce 41 55 41 89 d5 41 54 49 89 f4 be 02 00 00 00 55 4c 89 c5 53 89 fb <48> 8b 00 4c 89 c7 e8 18 61 54 e9 80 bd 80 04 00 00 00 75 09 4c 3b
[ 14.971933] RSP: 0018:ffffbaa841483838 EFLAGS: 00010282
[ 14.971938] RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffff9685e01ba568
[ 14.971941] RDX: 0000000000000008 RSI: 0000000000000002 RDI: 0000000000000000
[ 14.971944] RBP: ffff9685ca22f028 R08: ffff9685ca22f028 R09: ffff9685ca22f028
[ 14.971948] R10: 000000000000000b R11: 0000000000000580 R12: 0000000000000580
[ 14.971951] R13: 0000000000000008 R14: ffff9685e01ba568 R15: ffff9685c222f000
[ 14.971954] FS: 00007f8287c0ab40(0000) GS:ffff96a47f940000(0000) knlGS:0000000000000000
[ 14.971959] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 14.971963] CR2: 0000000000000000 CR3: 0000000168090001 CR4: 00000000003706f0
[ 14.971966] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 14.971968] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 14.971972] Call Trace:
[ 14.971977] <TASK>
[ 14.971981] ? show_trace_log_lvl+0x1c4/0x2df
[ 14.971994] ? show_trace_log_lvl+0x1c4/0x2df
[ 14.972003] ? acpi_ev_address_space_dispatch+0x16e/0x3c0
[ 14.972014] ? __die_body.cold+0x8/0xd
[ 14.972021] ? page_fault_oops+0x132/0x170
[ 14.972028] ? exc_page_fault+0x61/0x150
[ 14.972036] ? asm_exc_page_fault+0x22/0x30
[ 14.972045] ? i801_acpi_io_handler+0x2d/0xb0 [i2c_i801]
[ 14.972061] acpi_ev_address_space_dispatch+0x16e/0x3c0
[ 14.972069] ? __pfx_i801_acpi_io_handler+0x10/0x10 [i2c_i801]
[ 14.972085] acpi_ex_access_region+0x5b/0xd0
[ 14.972093] acpi_ex_field_datum_io+0x73/0x2e0
[ 14.972100] acpi_ex_read_data_from_field+0x8e/0x230
[ 14.972106] acpi_ex_resolve_node_to_value+0x23d/0x310
[ 14.972114] acpi_ds_evaluate_name_path+0xad/0x110
[ 14.972121] acpi_ds_exec_end_op+0x321/0x510
[ 14.972127] acpi_ps_parse_loop+0xf7/0x680
[ 14.972136] acpi_ps_parse_aml+0x17a/0x3d0
[ 14.972143] acpi_ps_execute_method+0x137/0x270
[ 14.972150] acpi_ns_evaluate+0x1f4/0x2e0
[ 14.972158] acpi_evaluate_object+0x134/0x2f0
[ 14.972164] acpi_evaluate_integer+0x50/0xe0
[ 14.972173] ? vsnprintf+0x24b/0x570
[ 14.972181] acpi_ac_get_state.part.0+0x23/0x70
[ 14.972189] get_ac_property+0x4e/0x60
[ 14.972195] power_supply_show_property+0x90/0x1f0
[ 14.972205] add_prop_uevent+0x29/0x90
[ 14.972213] power_supply_uevent+0x109/0x1d0
[ 14.972222] dev_uevent+0x10e/0x2f0
[ 14.972228] uevent_show+0x8e/0x100
[ 14.972236] dev_attr_show+0x19
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix NULL deref in mesh_matches_local()
mesh_matches_local() unconditionally dereferences ie->mesh_config to
compare mesh configuration parameters. When called from
mesh_rx_csa_frame(), the parsed action-frame elements may not contain a
Mesh Configuration IE, leaving ie->mesh_config NULL and triggering a
kernel NULL pointer dereference.
The other two callers are already safe:
- ieee80211_mesh_rx_bcn_presp() checks !elems->mesh_config before
calling mesh_matches_local()
- mesh_plink_get_event() is only reached through
mesh_process_plink_frame(), which checks !elems->mesh_config, too
mesh_rx_csa_frame() is the only caller that passes raw parsed elements
to mesh_matches_local() without guarding mesh_config. An adjacent
attacker can exploit this by sending a crafted CSA action frame that
includes a valid Mesh ID IE but omits the Mesh Configuration IE,
crashing the kernel.
The captured crash log:
Oops: general protection fault, probably for non-canonical address ...
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
Workqueue: events_unbound cfg80211_wiphy_work
[...]
Call Trace:
<TASK>
? __pfx_mesh_matches_local (net/mac80211/mesh.c:65)
ieee80211_mesh_rx_queued_mgmt (net/mac80211/mesh.c:1686)
[...]
ieee80211_iface_work (net/mac80211/iface.c:1754 net/mac80211/iface.c:1802)
[...]
cfg80211_wiphy_work (net/wireless/core.c:426)
process_one_work (net/kernel/workqueue.c:3280)
? assign_work (net/kernel/workqueue.c:1219)
worker_thread (net/kernel/workqueue.c:3352)
? __pfx_worker_thread (net/kernel/workqueue.c:3385)
kthread (net/kernel/kthread.c:436)
[...]
ret_from_fork_asm (net/arch/x86/entry/entry_64.S:255)
</TASK>
This patch adds a NULL check for ie->mesh_config at the top of
mesh_matches_local() to return false early when the Mesh Configuration
IE is absent. |
| In the Linux kernel, the following vulnerability has been resolved:
icmp: fix NULL pointer dereference in icmp_tag_validation()
icmp_tag_validation() unconditionally dereferences the result of
rcu_dereference(inet_protos[proto]) without checking for NULL.
The inet_protos[] array is sparse -- only about 15 of 256 protocol
numbers have registered handlers. When ip_no_pmtu_disc is set to 3
(hardened PMTU mode) and the kernel receives an ICMP Fragmentation
Needed error with a quoted inner IP header containing an unregistered
protocol number, the NULL dereference causes a kernel panic in
softirq context.
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000002: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
RIP: 0010:icmp_unreach (net/ipv4/icmp.c:1085 net/ipv4/icmp.c:1143)
Call Trace:
<IRQ>
icmp_rcv (net/ipv4/icmp.c:1527)
ip_protocol_deliver_rcu (net/ipv4/ip_input.c:207)
ip_local_deliver_finish (net/ipv4/ip_input.c:242)
ip_local_deliver (net/ipv4/ip_input.c:262)
ip_rcv (net/ipv4/ip_input.c:573)
__netif_receive_skb_one_core (net/core/dev.c:6164)
process_backlog (net/core/dev.c:6628)
handle_softirqs (kernel/softirq.c:561)
</IRQ>
Add a NULL check before accessing icmp_strict_tag_validation. If the
protocol has no registered handler, return false since it cannot
perform strict tag validation. |
| There is a NULL pointer dereference at function sixel_helper_set_additional_message (status.c) in libsixel 1.8.2 that will cause a denial of service. |
| In the Linux kernel, the following vulnerability has been resolved:
net: mvpp2: guard flow control update with global_tx_fc in buffer switching
mvpp2_bm_switch_buffers() unconditionally calls
mvpp2_bm_pool_update_priv_fc() when switching between per-cpu and
shared buffer pool modes. This function programs CM3 flow control
registers via mvpp2_cm3_read()/mvpp2_cm3_write(), which dereference
priv->cm3_base without any NULL check.
When the CM3 SRAM resource is not present in the device tree (the
third reg entry added by commit 60523583b07c ("dts: marvell: add CM3
SRAM memory to cp11x ethernet device tree")), priv->cm3_base remains
NULL and priv->global_tx_fc is false. Any operation that triggers
mvpp2_bm_switch_buffers(), for example an MTU change that crosses
the jumbo frame threshold, will crash:
Unable to handle kernel NULL pointer dereference at
virtual address 0000000000000000
Mem abort info:
ESR = 0x0000000096000006
EC = 0x25: DABT (current EL), IL = 32 bits
pc : readl+0x0/0x18
lr : mvpp2_cm3_read.isra.0+0x14/0x20
Call trace:
readl+0x0/0x18
mvpp2_bm_pool_update_fc+0x40/0x12c
mvpp2_bm_pool_update_priv_fc+0x94/0xd8
mvpp2_bm_switch_buffers.isra.0+0x80/0x1c0
mvpp2_change_mtu+0x140/0x380
__dev_set_mtu+0x1c/0x38
dev_set_mtu_ext+0x78/0x118
dev_set_mtu+0x48/0xa8
dev_ifsioc+0x21c/0x43c
dev_ioctl+0x2d8/0x42c
sock_ioctl+0x314/0x378
Every other flow control call site in the driver already guards
hardware access with either priv->global_tx_fc or port->tx_fc.
mvpp2_bm_switch_buffers() is the only place that omits this check.
Add the missing priv->global_tx_fc guard to both the disable and
re-enable calls in mvpp2_bm_switch_buffers(), consistent with the
rest of the driver. |
| In the Linux kernel, the following vulnerability has been resolved:
udp_tunnel: fix NULL deref caused by udp_sock_create6 when CONFIG_IPV6=n
When CONFIG_IPV6 is disabled, the udp_sock_create6() function returns 0
(success) without actually creating a socket. Callers such as
fou_create() then proceed to dereference the uninitialized socket
pointer, resulting in a NULL pointer dereference.
The captured NULL deref crash:
BUG: kernel NULL pointer dereference, address: 0000000000000018
RIP: 0010:fou_nl_add_doit (net/ipv4/fou_core.c:590 net/ipv4/fou_core.c:764)
[...]
Call Trace:
<TASK>
genl_family_rcv_msg_doit.constprop.0 (net/netlink/genetlink.c:1114)
genl_rcv_msg (net/netlink/genetlink.c:1194 net/netlink/genetlink.c:1209)
[...]
netlink_rcv_skb (net/netlink/af_netlink.c:2550)
genl_rcv (net/netlink/genetlink.c:1219)
netlink_unicast (net/netlink/af_netlink.c:1319 net/netlink/af_netlink.c:1344)
netlink_sendmsg (net/netlink/af_netlink.c:1894)
__sock_sendmsg (net/socket.c:727 (discriminator 1) net/socket.c:742 (discriminator 1))
__sys_sendto (./include/linux/file.h:62 (discriminator 1) ./include/linux/file.h:83 (discriminator 1) net/socket.c:2183 (discriminator 1))
__x64_sys_sendto (net/socket.c:2213 (discriminator 1) net/socket.c:2209 (discriminator 1) net/socket.c:2209 (discriminator 1))
do_syscall_64 (arch/x86/entry/syscall_64.c:63 (discriminator 1) arch/x86/entry/syscall_64.c:94 (discriminator 1))
entry_SYSCALL_64_after_hwframe (net/arch/x86/entry/entry_64.S:130)
This patch makes udp_sock_create6 return -EPFNOSUPPORT instead, so
callers correctly take their error paths. There is only one caller of
the vulnerable function and only privileged users can trigger it. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: allow MDIO bus PM ops to start/stop state machine for phylink-controlled PHY
DSA has 2 kinds of drivers:
1. Those who call dsa_switch_suspend() and dsa_switch_resume() from
their device PM ops: qca8k-8xxx, bcm_sf2, microchip ksz
2. Those who don't: all others. The above methods should be optional.
For type 1, dsa_switch_suspend() calls dsa_user_suspend() -> phylink_stop(),
and dsa_switch_resume() calls dsa_user_resume() -> phylink_start().
These seem good candidates for setting mac_managed_pm = true because
that is essentially its definition [1], but that does not seem to be the
biggest problem for now, and is not what this change focuses on.
Talking strictly about the 2nd category of DSA drivers here (which
do not have MAC managed PM, meaning that for their attached PHYs,
mdio_bus_phy_suspend() and mdio_bus_phy_resume() should run in full),
I have noticed that the following warning from mdio_bus_phy_resume() is
triggered:
WARN_ON(phydev->state != PHY_HALTED && phydev->state != PHY_READY &&
phydev->state != PHY_UP);
because the PHY state machine is running.
It's running as a result of a previous dsa_user_open() -> ... ->
phylink_start() -> phy_start() having been initiated by the user.
The previous mdio_bus_phy_suspend() was supposed to have called
phy_stop_machine(), but it didn't. So this is why the PHY is in state
PHY_NOLINK by the time mdio_bus_phy_resume() runs.
mdio_bus_phy_suspend() did not call phy_stop_machine() because for
phylink, the phydev->adjust_link function pointer is NULL. This seems a
technicality introduced by commit fddd91016d16 ("phylib: fix PAL state
machine restart on resume"). That commit was written before phylink
existed, and was intended to avoid crashing with consumer drivers which
don't use the PHY state machine - phylink always does, when using a PHY.
But phylink itself has historically not been developed with
suspend/resume in mind, and apparently not tested too much in that
scenario, allowing this bug to exist unnoticed for so long. Plus, prior
to the WARN_ON(), it would have likely been invisible.
This issue is not in fact restricted to type 2 DSA drivers (according to
the above ad-hoc classification), but can be extrapolated to any MAC
driver with phylink and MDIO-bus-managed PHY PM ops. DSA is just where
the issue was reported. Assuming mac_managed_pm is set correctly, a
quick search indicates the following other drivers might be affected:
$ grep -Zlr PHYLINK_NETDEV drivers/ | xargs -0 grep -L mac_managed_pm
drivers/net/ethernet/atheros/ag71xx.c
drivers/net/ethernet/microchip/sparx5/sparx5_main.c
drivers/net/ethernet/microchip/lan966x/lan966x_main.c
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c
drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c
drivers/net/ethernet/freescale/ucc_geth.c
drivers/net/ethernet/freescale/enetc/enetc_pf_common.c
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
drivers/net/ethernet/marvell/mvneta.c
drivers/net/ethernet/marvell/prestera/prestera_main.c
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/altera/altera_tse_main.c
drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
drivers/net/ethernet/meta/fbnic/fbnic_phylink.c
drivers/net/ethernet/tehuti/tn40_phy.c
drivers/net/ethernet/mscc/ocelot_net.c
Make the existing conditions dependent on the PHY device having a
phydev->phy_link_change() implementation equal to the default
phy_link_change() provided by phylib. Otherwise, we implicitly know that
the phydev has the phylink-provided phylink_phy_change() callback, and
when phylink is used, the PHY state machine always needs to be stopped/
started on the suspend/resume path. The code is structured as such that
if phydev->phy_link_change() is absent, it is a matter of time until the
kernel will crash - no need to further complicate the test.
Thus, for the situation where the PM is not managed b
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: endpoint: Avoid creating sub-groups asynchronously
The asynchronous creation of sub-groups by a delayed work could lead to a
NULL pointer dereference when the driver directory is removed before the
work completes.
The crash can be easily reproduced with the following commands:
# cd /sys/kernel/config/pci_ep/functions/pci_epf_test
# for i in {1..20}; do mkdir test && rmdir test; done
BUG: kernel NULL pointer dereference, address: 0000000000000088
...
Call Trace:
configfs_register_group+0x3d/0x190
pci_epf_cfs_work+0x41/0x110
process_one_work+0x18f/0x350
worker_thread+0x25a/0x3a0
Fix this issue by using configfs_add_default_group() API which does not
have the deadlock problem as configfs_register_group() and does not require
the delayed work handler.
[mani: slightly reworded the description and added stable list] |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix null pointer dereference error in generate_encryptionkey
If client send two session setups with krb5 authenticate to ksmbd,
null pointer dereference error in generate_encryptionkey could happen.
sess->Preauth_HashValue is set to NULL if session is valid.
So this patch skip generate encryption key if session is valid. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: TC, delete flows only for existing peers
When deleting TC steering flows, iterate only over actual devcom
peers instead of assuming all possible ports exist. This avoids
touching non-existent peers and ensures cleanup is limited to
devices the driver is currently connected to.
BUG: kernel NULL pointer dereference, address: 0000000000000008
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 133c8a067 P4D 0
Oops: Oops: 0002 [#1] SMP
CPU: 19 UID: 0 PID: 2169 Comm: tc Not tainted 6.18.0+ #156 NONE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
RIP: 0010:mlx5e_tc_del_fdb_peers_flow+0xbe/0x200 [mlx5_core]
Code: 00 00 a8 08 74 a8 49 8b 46 18 f6 c4 02 74 9f 4c 8d bf a0 12 00 00 4c 89 ff e8 0e e7 96 e1 49 8b 44 24 08 49 8b 0c 24 4c 89 ff <48> 89 41 08 48 89 08 49 89 2c 24 49 89 5c 24 08 e8 7d ce 96 e1 49
RSP: 0018:ff11000143867528 EFLAGS: 00010246
RAX: 0000000000000000 RBX: dead000000000122 RCX: 0000000000000000
RDX: ff11000143691580 RSI: ff110001026e5000 RDI: ff11000106f3d2a0
RBP: dead000000000100 R08: 00000000000003fd R09: 0000000000000002
R10: ff11000101c75690 R11: ff1100085faea178 R12: ff11000115f0ae78
R13: 0000000000000000 R14: ff11000115f0a800 R15: ff11000106f3d2a0
FS: 00007f35236bf740(0000) GS:ff110008dc809000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 0000000157a01001 CR4: 0000000000373eb0
Call Trace:
<TASK>
mlx5e_tc_del_flow+0x46/0x270 [mlx5_core]
mlx5e_flow_put+0x25/0x50 [mlx5_core]
mlx5e_delete_flower+0x2a6/0x3e0 [mlx5_core]
tc_setup_cb_reoffload+0x20/0x80
fl_reoffload+0x26f/0x2f0 [cls_flower]
? mlx5e_tc_reoffload_flows_work+0xc0/0xc0 [mlx5_core]
? mlx5e_tc_reoffload_flows_work+0xc0/0xc0 [mlx5_core]
tcf_block_playback_offloads+0x9e/0x1c0
tcf_block_unbind+0x7b/0xd0
tcf_block_setup+0x186/0x1d0
tcf_block_offload_cmd.isra.0+0xef/0x130
tcf_block_offload_unbind+0x43/0x70
__tcf_block_put+0x85/0x160
ingress_destroy+0x32/0x110 [sch_ingress]
__qdisc_destroy+0x44/0x100
qdisc_graft+0x22b/0x610
tc_get_qdisc+0x183/0x4d0
rtnetlink_rcv_msg+0x2d7/0x3d0
? rtnl_calcit.isra.0+0x100/0x100
netlink_rcv_skb+0x53/0x100
netlink_unicast+0x249/0x320
? __alloc_skb+0x102/0x1f0
netlink_sendmsg+0x1e3/0x420
__sock_sendmsg+0x38/0x60
____sys_sendmsg+0x1ef/0x230
? copy_msghdr_from_user+0x6c/0xa0
___sys_sendmsg+0x7f/0xc0
? ___sys_recvmsg+0x8a/0xc0
? __sys_sendto+0x119/0x180
__sys_sendmsg+0x61/0xb0
do_syscall_64+0x55/0x640
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f35238bb764
Code: 15 b9 86 0c 00 f7 d8 64 89 02 b8 ff ff ff ff eb bf 0f 1f 44 00 00 f3 0f 1e fa 80 3d e5 08 0d 00 00 74 13 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 4c c3 0f 1f 00 55 48 89 e5 48 83 ec 20 89 55
RSP: 002b:00007ffed4c35638 EFLAGS: 00000202 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 000055a2efcc75e0 RCX: 00007f35238bb764
RDX: 0000000000000000 RSI: 00007ffed4c356a0 RDI: 0000000000000003
RBP: 00007ffed4c35710 R08: 0000000000000010 R09: 00007f3523984b20
R10: 0000000000000004 R11: 0000000000000202 R12: 00007ffed4c35790
R13: 000000006947df8f R14: 000055a2efcc75e0 R15: 00007ffed4c35780 |
| iccDEV provides a set of libraries and tools for working with ICC color management profiles. Versions 2.3.1.1 and below are prone to have Undefined Behavior (UB) and Out of Memory errors. This issue is fixed in version 2.3.1.2. |
| ImageMagick is free and open-source software used for editing and manipulating digital images. Versions 14.10.1 and below have a NULL pointer dereference vulnerability in the MSL (Magick Scripting Language) parser when processing <comment> tags before images are loaded. This can lead to DoS attack due to assertion failure (debug builds) or NULL pointer dereference (release builds). This issue is fixed in version 14.10.2. |
| In the Linux kernel, the following vulnerability has been resolved:
net: mscc: ocelot: Fix crash when adding interface under a lag
Commit 15faa1f67ab4 ("lan966x: Fix crash when adding interface under a lag")
fixed a similar issue in the lan966x driver caused by a NULL pointer dereference.
The ocelot_set_aggr_pgids() function in the ocelot driver has similar logic
and is susceptible to the same crash.
This issue specifically affects the ocelot_vsc7514.c frontend, which leaves
unused ports as NULL pointers. The felix_vsc9959.c frontend is unaffected as
it uses the DSA framework which registers all ports.
Fix this by checking if the port pointer is valid before accessing it. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Don't store mlx5e_priv in mlx5e_dev devlink priv
mlx5e_priv is an unstable structure that can be memset(0) if profile
attaching fails, mlx5e_priv in mlx5e_dev devlink private is used to
reference the netdev and mdev associated with that struct. Instead,
store netdev directly into mlx5e_dev and get mdev from the containing
mlx5_adev aux device structure.
This fixes a kernel oops in mlx5e_remove when switchdev mode fails due
to change profile failure.
$ devlink dev eswitch set pci/0000:00:03.0 mode switchdev
Error: mlx5_core: Failed setting eswitch to offloads.
dmesg:
workqueue: Failed to create a rescuer kthread for wq "mlx5e": -EINTR
mlx5_core 0012:03:00.1: mlx5e_netdev_init_profile:6214:(pid 37199): mlx5e_priv_init failed, err=-12
mlx5_core 0012:03:00.1 gpu3rdma1: mlx5e_netdev_change_profile: new profile init failed, -12
workqueue: Failed to create a rescuer kthread for wq "mlx5e": -EINTR
mlx5_core 0012:03:00.1: mlx5e_netdev_init_profile:6214:(pid 37199): mlx5e_priv_init failed, err=-12
mlx5_core 0012:03:00.1 gpu3rdma1: mlx5e_netdev_change_profile: failed to rollback to orig profile, -12
$ devlink dev reload pci/0000:00:03.0 ==> oops
BUG: kernel NULL pointer dereference, address: 0000000000000520
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: Oops: 0000 [#1] SMP NOPTI
CPU: 3 UID: 0 PID: 521 Comm: devlink Not tainted 6.18.0-rc5+ #117 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-2.fc40 04/01/2014
RIP: 0010:mlx5e_remove+0x68/0x130
RSP: 0018:ffffc900034838f0 EFLAGS: 00010246
RAX: ffff88810283c380 RBX: ffff888101874400 RCX: ffffffff826ffc45
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000000
RBP: ffff888102d789c0 R08: ffff8881007137f0 R09: ffff888100264e10
R10: ffffc90003483898 R11: ffffc900034838a0 R12: ffff888100d261a0
R13: ffff888100d261a0 R14: ffff8881018749a0 R15: ffff888101874400
FS: 00007f8565fea740(0000) GS:ffff88856a759000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000520 CR3: 000000010b11a004 CR4: 0000000000370ef0
Call Trace:
<TASK>
device_release_driver_internal+0x19c/0x200
bus_remove_device+0xc6/0x130
device_del+0x160/0x3d0
? devl_param_driverinit_value_get+0x2d/0x90
mlx5_detach_device+0x89/0xe0
mlx5_unload_one_devl_locked+0x3a/0x70
mlx5_devlink_reload_down+0xc8/0x220
devlink_reload+0x7d/0x260
devlink_nl_reload_doit+0x45b/0x5a0
genl_family_rcv_msg_doit+0xe8/0x140 |
| A security flaw has been discovered in GPAC up to 2.4.0. Affected by this vulnerability is the function DumpMovieInfo of the file applications/mp4box/filedump.c. The manipulation results in null pointer dereference. The attack must be initiated from a local position. The exploit has been released to the public and may be used for attacks. The patch is identified as d45c264c20addf0c1cc05124ede33f8ffa800e68. It is advisable to implement a patch to correct this issue. |
| Rekor is a software supply chain transparency log. In versions 1.4.3 and below, the entry implementation can panic on attacker-controlled input when canonicalizing a proposed entry with an empty spec.message, causing nil Pointer Dereference. Function validate() returns nil (success) when message is empty, leaving sign1Msg uninitialized, and Canonicalize() later dereferences v.sign1Msg.Payload. A malformed proposed entry of the cose/v0.0.1 type can cause a panic on a thread within the Rekor process. The thread is recovered so the client receives a 500 error message and service still continues, so the availability impact of this is minimal. This issue has been fixed in version 1.5.0. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: act_api: avoid dereferencing ERR_PTR in tcf_idrinfo_destroy
syzbot reported a crash in tc_act_in_hw() during netns teardown where
tcf_idrinfo_destroy() passed an ERR_PTR(-EBUSY) value as a tc_action
pointer, leading to an invalid dereference.
Guard against ERR_PTR entries when iterating the action IDR so teardown
does not call tc_act_in_hw() on an error pointer. |
