| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
RISC-V: KVM: Write hgatp register with valid mode bits
According to the RISC-V Privileged Architecture Spec, when MODE=Bare
is selected,software must write zero to the remaining fields of hgatp.
We have detected the valid mode supported by the HW before, So using a
valid mode to detect how many vmid bits are supported. |
| In the Linux kernel, the following vulnerability has been resolved:
mailbox: zynqmp-ipi: Fix out-of-bounds access in mailbox cleanup loop
The cleanup loop was starting at the wrong array index, causing
out-of-bounds access.
Start the loop at the correct index for zero-indexed arrays to prevent
accessing memory beyond the allocated array bounds. |
| In the Linux kernel, the following vulnerability has been resolved:
can: gs_usb: gs_usb_receive_bulk_callback(): check actual_length before accessing data
The URB received in gs_usb_receive_bulk_callback() contains a struct
gs_host_frame. The length of the data after the header depends on the
gs_host_frame hf::flags and the active device features (e.g. time
stamping).
Introduce a new function gs_usb_get_minimum_length() and check that we have
at least received the required amount of data before accessing it. Only
copy the data to that skb that has actually been received.
[mkl: rename gs_usb_get_minimum_length() -> +gs_usb_get_minimum_rx_length()] |
| In the Linux kernel, the following vulnerability has been resolved:
md: avoid repeated calls to del_gendisk
There is a uaf problem which is found by case 23rdev-lifetime:
Oops: general protection fault, probably for non-canonical address 0xdead000000000122
RIP: 0010:bdi_unregister+0x4b/0x170
Call Trace:
<TASK>
__del_gendisk+0x356/0x3e0
mddev_unlock+0x351/0x360
rdev_attr_store+0x217/0x280
kernfs_fop_write_iter+0x14a/0x210
vfs_write+0x29e/0x550
ksys_write+0x74/0xf0
do_syscall_64+0xbb/0x380
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7ff5250a177e
The sequence is:
1. rdev remove path gets reconfig_mutex
2. rdev remove path release reconfig_mutex in mddev_unlock
3. md stop calls do_md_stop and sets MD_DELETED
4. rdev remove path calls del_gendisk because MD_DELETED is set
5. md stop path release reconfig_mutex and calls del_gendisk again
So there is a race condition we should resolve. This patch adds a
flag MD_DO_DELETE to avoid the race condition. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86: Fix NULL event access and potential PEBS record loss
When intel_pmu_drain_pebs_icl() is called to drain PEBS records, the
perf_event_overflow() could be called to process the last PEBS record.
While perf_event_overflow() could trigger the interrupt throttle and
stop all events of the group, like what the below call-chain shows.
perf_event_overflow()
-> __perf_event_overflow()
->__perf_event_account_interrupt()
-> perf_event_throttle_group()
-> perf_event_throttle()
-> event->pmu->stop()
-> x86_pmu_stop()
The side effect of stopping the events is that all corresponding event
pointers in cpuc->events[] array are cleared to NULL.
Assume there are two PEBS events (event a and event b) in a group. When
intel_pmu_drain_pebs_icl() calls perf_event_overflow() to process the
last PEBS record of PEBS event a, interrupt throttle is triggered and
all pointers of event a and event b are cleared to NULL. Then
intel_pmu_drain_pebs_icl() tries to process the last PEBS record of
event b and encounters NULL pointer access.
To avoid this issue, move cpuc->events[] clearing from x86_pmu_stop()
to x86_pmu_del(). It's safe since cpuc->active_mask or
cpuc->pebs_enabled is always checked before access the event pointer
from cpuc->events[]. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: core: Fix data race in CPU latency PM QoS request handling
The cpu_latency_qos_add/remove/update_request interfaces lack internal
synchronization by design, requiring the caller to ensure thread safety.
The current implementation relies on the 'pm_qos_enabled' flag, which is
insufficient to prevent concurrent access and cannot serve as a proper
synchronization mechanism. This has led to data races and list
corruption issues.
A typical race condition call trace is:
[Thread A]
ufshcd_pm_qos_exit()
--> cpu_latency_qos_remove_request()
--> cpu_latency_qos_apply();
--> pm_qos_update_target()
--> plist_del <--(1) delete plist node
--> memset(req, 0, sizeof(*req));
--> hba->pm_qos_enabled = false;
[Thread B]
ufshcd_devfreq_target
--> ufshcd_devfreq_scale
--> ufshcd_scale_clks
--> ufshcd_pm_qos_update <--(2) pm_qos_enabled is true
--> cpu_latency_qos_update_request
--> pm_qos_update_target
--> plist_del <--(3) plist node use-after-free
Introduces a dedicated mutex to serialize PM QoS operations, preventing
data races and ensuring safe access to PM QoS resources, including sysfs
interface reads. |
| In the Linux kernel, the following vulnerability has been resolved:
xen/events: Return -EEXIST for bound VIRQs
Change find_virq() to return -EEXIST when a VIRQ is bound to a
different CPU than the one passed in. With that, remove the BUG_ON()
from bind_virq_to_irq() to propogate the error upwards.
Some VIRQs are per-cpu, but others are per-domain or global. Those must
be bound to CPU0 and can then migrate elsewhere. The lookup for
per-domain and global will probably fail when migrated off CPU 0,
especially when the current CPU is tracked. This now returns -EEXIST
instead of BUG_ON().
A second call to bind a per-domain or global VIRQ is not expected, but
make it non-fatal to avoid trying to look up the irq, since we don't
know which per_cpu(virq_to_irq) it will be in. |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: client: fix memory leak in smb3_fs_context_parse_param
The user calls fsconfig twice, but when the program exits, free() only
frees ctx->source for the second fsconfig, not the first.
Regarding fc->source, there is no code in the fs context related to its
memory reclamation.
To fix this memory leak, release the source memory corresponding to ctx
or fc before each parsing.
syzbot reported:
BUG: memory leak
unreferenced object 0xffff888128afa360 (size 96):
backtrace (crc 79c9c7ba):
kstrdup+0x3c/0x80 mm/util.c:84
smb3_fs_context_parse_param+0x229b/0x36c0 fs/smb/client/fs_context.c:1444
BUG: memory leak
unreferenced object 0xffff888112c7d900 (size 96):
backtrace (crc 79c9c7ba):
smb3_fs_context_fullpath+0x70/0x1b0 fs/smb/client/fs_context.c:629
smb3_fs_context_parse_param+0x2266/0x36c0 fs/smb/client/fs_context.c:1438 |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Shutdown FW DMA in bnxt_shutdown()
The netif_close() call in bnxt_shutdown() only stops packet DMA. There
may be FW DMA for trace logging (recently added) that will continue. If
we kexec to a new kernel, the DMA will corrupt memory in the new kernel.
Add bnxt_hwrm_func_drv_unrgtr() to unregister the driver from the FW.
This will stop the FW DMA. In case the call fails, call pcie_flr() to
reset the function and stop the DMA. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid0, raid10: Don't set discard sectors for request queue
It should use disk_stack_limits to get a proper max_discard_sectors
rather than setting a value by stack drivers.
And there is a bug. If all member disks are rotational devices,
raid0/raid10 set max_discard_sectors. So the member devices are
not ssd/nvme, but raid0/raid10 export the wrong value. It reports
warning messages in function __blkdev_issue_discard when mkfs.xfs
like this:
[ 4616.022599] ------------[ cut here ]------------
[ 4616.027779] WARNING: CPU: 4 PID: 99634 at block/blk-lib.c:50 __blkdev_issue_discard+0x16a/0x1a0
[ 4616.140663] RIP: 0010:__blkdev_issue_discard+0x16a/0x1a0
[ 4616.146601] Code: 24 4c 89 20 31 c0 e9 fe fe ff ff c1 e8 09 8d 48 ff 4c 89 f0 4c 09 e8 48 85 c1 0f 84 55 ff ff ff b8 ea ff ff ff e9 df fe ff ff <0f> 0b 48 8d 74 24 08 e8 ea d6 00 00 48 c7 c6 20 1e 89 ab 48 c7 c7
[ 4616.167567] RSP: 0018:ffffaab88cbffca8 EFLAGS: 00010246
[ 4616.173406] RAX: ffff9ba1f9e44678 RBX: 0000000000000000 RCX: ffff9ba1c9792080
[ 4616.181376] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9ba1c9792080
[ 4616.189345] RBP: 0000000000000cc0 R08: ffffaab88cbffd10 R09: 0000000000000000
[ 4616.197317] R10: 0000000000000012 R11: 0000000000000000 R12: 0000000000000000
[ 4616.205288] R13: 0000000000400000 R14: 0000000000000cc0 R15: ffff9ba1c9792080
[ 4616.213259] FS: 00007f9a5534e980(0000) GS:ffff9ba1b7c80000(0000) knlGS:0000000000000000
[ 4616.222298] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 4616.228719] CR2: 000055a390a4c518 CR3: 0000000123e40006 CR4: 00000000001706e0
[ 4616.236689] Call Trace:
[ 4616.239428] blkdev_issue_discard+0x52/0xb0
[ 4616.244108] blkdev_common_ioctl+0x43c/0xa00
[ 4616.248883] blkdev_ioctl+0x116/0x280
[ 4616.252977] __x64_sys_ioctl+0x8a/0xc0
[ 4616.257163] do_syscall_64+0x5c/0x90
[ 4616.261164] ? handle_mm_fault+0xc5/0x2a0
[ 4616.265652] ? do_user_addr_fault+0x1d8/0x690
[ 4616.270527] ? do_syscall_64+0x69/0x90
[ 4616.274717] ? exc_page_fault+0x62/0x150
[ 4616.279097] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[ 4616.284748] RIP: 0033:0x7f9a55398c6b |
| In the Linux kernel, the following vulnerability has been resolved:
misc: pci_endpoint_test: Fix pci_endpoint_test_{copy,write,read}() panic
The dma_map_single() doesn't permit zero length mapping. It causes a follow
panic.
A panic was reported on arm64:
[ 60.137988] ------------[ cut here ]------------
[ 60.142630] kernel BUG at kernel/dma/swiotlb.c:624!
[ 60.147508] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 60.152992] Modules linked in: dw_hdmi_cec crct10dif_ce simple_bridge rcar_fdp1 vsp1 rcar_vin videobuf2_vmalloc rcar_csi2 v4l
2_mem2mem videobuf2_dma_contig videobuf2_memops pci_endpoint_test videobuf2_v4l2 videobuf2_common rcar_fcp v4l2_fwnode v4l2_asyn
c videodev mc gpio_bd9571mwv max9611 pwm_rcar ccree at24 authenc libdes phy_rcar_gen3_usb3 usb_dmac display_connector pwm_bl
[ 60.186252] CPU: 0 PID: 508 Comm: pcitest Not tainted 6.0.0-rc1rpci-dev+ #237
[ 60.193387] Hardware name: Renesas Salvator-X 2nd version board based on r8a77951 (DT)
[ 60.201302] pstate: 00000005 (nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 60.208263] pc : swiotlb_tbl_map_single+0x2c0/0x590
[ 60.213149] lr : swiotlb_map+0x88/0x1f0
[ 60.216982] sp : ffff80000a883bc0
[ 60.220292] x29: ffff80000a883bc0 x28: 0000000000000000 x27: 0000000000000000
[ 60.227430] x26: 0000000000000000 x25: ffff0004c0da20d0 x24: ffff80000a1f77c0
[ 60.234567] x23: 0000000000000002 x22: 0001000040000010 x21: 000000007a000000
[ 60.241703] x20: 0000000000200000 x19: 0000000000000000 x18: 0000000000000000
[ 60.248840] x17: 0000000000000000 x16: 0000000000000000 x15: ffff0006ff7b9180
[ 60.255977] x14: ffff0006ff7b9180 x13: 0000000000000000 x12: 0000000000000000
[ 60.263113] x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000
[ 60.270249] x8 : 0001000000000010 x7 : ffff0004c6754b20 x6 : 0000000000000000
[ 60.277385] x5 : ffff0004c0da2090 x4 : 0000000000000000 x3 : 0000000000000001
[ 60.284521] x2 : 0000000040000000 x1 : 0000000000000000 x0 : 0000000040000010
[ 60.291658] Call trace:
[ 60.294100] swiotlb_tbl_map_single+0x2c0/0x590
[ 60.298629] swiotlb_map+0x88/0x1f0
[ 60.302115] dma_map_page_attrs+0x188/0x230
[ 60.306299] pci_endpoint_test_ioctl+0x5e4/0xd90 [pci_endpoint_test]
[ 60.312660] __arm64_sys_ioctl+0xa8/0xf0
[ 60.316583] invoke_syscall+0x44/0x108
[ 60.320334] el0_svc_common.constprop.0+0xcc/0xf0
[ 60.325038] do_el0_svc+0x2c/0xb8
[ 60.328351] el0_svc+0x2c/0x88
[ 60.331406] el0t_64_sync_handler+0xb8/0xc0
[ 60.335587] el0t_64_sync+0x18c/0x190
[ 60.339251] Code: 52800013 d2e00414 35fff45c d503201f (d4210000)
[ 60.345344] ---[ end trace 0000000000000000 ]---
To fix it, this patch adds a checking the payload length if it is zero. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: core: Use different devices for resource allocation and DT lookup
Following by the below discussion, there's the potential UAF issue
between regulator and mfd.
https://lore.kernel.org/all/20221128143601.1698148-1-yangyingliang@huawei.com/
From the analysis of Yingliang
CPU A |CPU B
mt6370_probe() |
devm_mfd_add_devices() |
|mt6370_regulator_probe()
| regulator_register()
| //allocate init_data and add it to devres
| regulator_of_get_init_data()
i2c_unregister_device() |
device_del() |
devres_release_all() |
// init_data is freed |
release_nodes() |
| // using init_data causes UAF
| regulator_register()
It's common to use mfd core to create child device for the regulator.
In order to do the DT lookup for init data, the child that registered
the regulator would pass its parent as the parameter. And this causes
init data resource allocated to its parent, not itself. The issue happen
when parent device is going to release and regulator core is still doing
some operation of init data constraint for the regulator of child device.
To fix it, this patch expand 'regulator_register' API to use the
different devices for init data allocation and DT lookup. |
| In the Linux kernel, the following vulnerability has been resolved:
dm: verity-loadpin: Only trust verity targets with enforcement
Verity targets can be configured to ignore corrupted data blocks.
LoadPin must only trust verity targets that are configured to
perform some kind of enforcement when data corruption is detected,
like returning an error, restarting the system or triggering a
panic. |
| In the Linux kernel, the following vulnerability has been resolved:
media: dvb-usb: fix memory leak in dvb_usb_adapter_init()
Syzbot reports a memory leak in "dvb_usb_adapter_init()".
The leak is due to not accounting for and freeing current iteration's
adapter->priv in case of an error. Currently if an error occurs,
it will exit before incrementing "num_adapters_initalized",
which is used as a reference counter to free all adap->priv
in "dvb_usb_adapter_exit()". There are multiple error paths that
can exit from before incrementing the counter. Including the
error handling paths for "dvb_usb_adapter_stream_init()",
"dvb_usb_adapter_dvb_init()" and "dvb_usb_adapter_frontend_init()"
within "dvb_usb_adapter_init()".
This means that in case of an error in any of these functions the
current iteration is not accounted for and the current iteration's
adap->priv is not freed.
Fix this by freeing the current iteration's adap->priv in the
"stream_init_err:" label in the error path. The rest of the
(accounted for) adap->priv objects are freed in dvb_usb_adapter_exit()
as expected using the num_adapters_initalized variable.
Syzbot report:
BUG: memory leak
unreferenced object 0xffff8881172f1a00 (size 512):
comm "kworker/0:2", pid 139, jiffies 4294994873 (age 10.960s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff844af012>] dvb_usb_adapter_init drivers/media/usb/dvb-usb/dvb-usb-init.c:75 [inline]
[<ffffffff844af012>] dvb_usb_init drivers/media/usb/dvb-usb/dvb-usb-init.c:184 [inline]
[<ffffffff844af012>] dvb_usb_device_init.cold+0x4e5/0x79e drivers/media/usb/dvb-usb/dvb-usb-init.c:308
[<ffffffff830db21d>] dib0700_probe+0x8d/0x1b0 drivers/media/usb/dvb-usb/dib0700_core.c:883
[<ffffffff82d3fdc7>] usb_probe_interface+0x177/0x370 drivers/usb/core/driver.c:396
[<ffffffff8274ab37>] call_driver_probe drivers/base/dd.c:542 [inline]
[<ffffffff8274ab37>] really_probe.part.0+0xe7/0x310 drivers/base/dd.c:621
[<ffffffff8274ae6c>] really_probe drivers/base/dd.c:583 [inline]
[<ffffffff8274ae6c>] __driver_probe_device+0x10c/0x1e0 drivers/base/dd.c:752
[<ffffffff8274af6a>] driver_probe_device+0x2a/0x120 drivers/base/dd.c:782
[<ffffffff8274b786>] __device_attach_driver+0xf6/0x140 drivers/base/dd.c:899
[<ffffffff82747c87>] bus_for_each_drv+0xb7/0x100 drivers/base/bus.c:427
[<ffffffff8274b352>] __device_attach+0x122/0x260 drivers/base/dd.c:970
[<ffffffff827498f6>] bus_probe_device+0xc6/0xe0 drivers/base/bus.c:487
[<ffffffff82745cdb>] device_add+0x5fb/0xdf0 drivers/base/core.c:3405
[<ffffffff82d3d202>] usb_set_configuration+0x8f2/0xb80 drivers/usb/core/message.c:2170
[<ffffffff82d4dbfc>] usb_generic_driver_probe+0x8c/0xc0 drivers/usb/core/generic.c:238
[<ffffffff82d3f49c>] usb_probe_device+0x5c/0x140 drivers/usb/core/driver.c:293
[<ffffffff8274ab37>] call_driver_probe drivers/base/dd.c:542 [inline]
[<ffffffff8274ab37>] really_probe.part.0+0xe7/0x310 drivers/base/dd.c:621
[<ffffffff8274ae6c>] really_probe drivers/base/dd.c:583 [inline]
[<ffffffff8274ae6c>] __driver_probe_device+0x10c/0x1e0 drivers/base/dd.c:752 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/gud: Fix UBSAN warning
UBSAN complains about invalid value for bool:
[ 101.165172] [drm] Initialized gud 1.0.0 20200422 for 2-3.2:1.0 on minor 1
[ 101.213360] gud 2-3.2:1.0: [drm] fb1: guddrmfb frame buffer device
[ 101.213426] usbcore: registered new interface driver gud
[ 101.989431] ================================================================================
[ 101.989441] UBSAN: invalid-load in linux/include/linux/iosys-map.h:253:9
[ 101.989447] load of value 121 is not a valid value for type '_Bool'
[ 101.989451] CPU: 1 PID: 455 Comm: kworker/1:6 Not tainted 5.18.0-rc5-gud-5.18-rc5 #3
[ 101.989456] Hardware name: Hewlett-Packard HP EliteBook 820 G1/1991, BIOS L71 Ver. 01.44 04/12/2018
[ 101.989459] Workqueue: events_long gud_flush_work [gud]
[ 101.989471] Call Trace:
[ 101.989474] <TASK>
[ 101.989479] dump_stack_lvl+0x49/0x5f
[ 101.989488] dump_stack+0x10/0x12
[ 101.989493] ubsan_epilogue+0x9/0x3b
[ 101.989498] __ubsan_handle_load_invalid_value.cold+0x44/0x49
[ 101.989504] dma_buf_vmap.cold+0x38/0x3d
[ 101.989511] ? find_busiest_group+0x48/0x300
[ 101.989520] drm_gem_shmem_vmap+0x76/0x1b0 [drm_shmem_helper]
[ 101.989528] drm_gem_shmem_object_vmap+0x9/0xb [drm_shmem_helper]
[ 101.989535] drm_gem_vmap+0x26/0x60 [drm]
[ 101.989594] drm_gem_fb_vmap+0x47/0x150 [drm_kms_helper]
[ 101.989630] gud_prep_flush+0xc1/0x710 [gud]
[ 101.989639] ? _raw_spin_lock+0x17/0x40
[ 101.989648] gud_flush_work+0x1e0/0x430 [gud]
[ 101.989653] ? __switch_to+0x11d/0x470
[ 101.989664] process_one_work+0x21f/0x3f0
[ 101.989673] worker_thread+0x200/0x3e0
[ 101.989679] ? rescuer_thread+0x390/0x390
[ 101.989684] kthread+0xfd/0x130
[ 101.989690] ? kthread_complete_and_exit+0x20/0x20
[ 101.989696] ret_from_fork+0x22/0x30
[ 101.989706] </TASK>
[ 101.989708] ================================================================================
The source of this warning is in iosys_map_clear() called from
dma_buf_vmap(). It conditionally sets values based on map->is_iomem. The
iosys_map variables are allocated uninitialized on the stack leading to
->is_iomem having all kinds of values and not only 0/1.
Fix this by zeroing the iosys_map variables. |
| In the Linux kernel, the following vulnerability has been resolved:
net: netpoll: fix incorrect refcount handling causing incorrect cleanup
commit efa95b01da18 ("netpoll: fix use after free") incorrectly
ignored the refcount and prematurely set dev->npinfo to NULL during
netpoll cleanup, leading to improper behavior and memory leaks.
Scenario causing lack of proper cleanup:
1) A netpoll is associated with a NIC (e.g., eth0) and netdev->npinfo is
allocated, and refcnt = 1
- Keep in mind that npinfo is shared among all netpoll instances. In
this case, there is just one.
2) Another netpoll is also associated with the same NIC and
npinfo->refcnt += 1.
- Now dev->npinfo->refcnt = 2;
- There is just one npinfo associated to the netdev.
3) When the first netpolls goes to clean up:
- The first cleanup succeeds and clears np->dev->npinfo, ignoring
refcnt.
- It basically calls `RCU_INIT_POINTER(np->dev->npinfo, NULL);`
- Set dev->npinfo = NULL, without proper cleanup
- No ->ndo_netpoll_cleanup() is either called
4) Now the second target tries to clean up
- The second cleanup fails because np->dev->npinfo is already NULL.
* In this case, ops->ndo_netpoll_cleanup() was never called, and
the skb pool is not cleaned as well (for the second netpoll
instance)
- This leaks npinfo and skbpool skbs, which is clearly reported by
kmemleak.
Revert commit efa95b01da18 ("netpoll: fix use after free") and adds
clarifying comments emphasizing that npinfo cleanup should only happen
once the refcount reaches zero, ensuring stable and correct netpoll
behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/namespace: fix reference leak in grab_requested_mnt_ns
lookup_mnt_ns() already takes a reference on mnt_ns.
grab_requested_mnt_ns() doesn't need to take an extra reference. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btusb: mediatek: Fix kernel crash when releasing mtk iso interface
When performing reset tests and encountering abnormal card drop issues
that lead to a kernel crash, it is necessary to perform a null check
before releasing resources to avoid attempting to release a null pointer.
<4>[ 29.158070] Hardware name: Google Quigon sku196612/196613 board (DT)
<4>[ 29.158076] Workqueue: hci0 hci_cmd_sync_work [bluetooth]
<4>[ 29.158154] pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
<4>[ 29.158162] pc : klist_remove+0x90/0x158
<4>[ 29.158174] lr : klist_remove+0x88/0x158
<4>[ 29.158180] sp : ffffffc0846b3c00
<4>[ 29.158185] pmr_save: 000000e0
<4>[ 29.158188] x29: ffffffc0846b3c30 x28: ffffff80cd31f880 x27: ffffff80c1bdc058
<4>[ 29.158199] x26: dead000000000100 x25: ffffffdbdc624ea3 x24: ffffff80c1bdc4c0
<4>[ 29.158209] x23: ffffffdbdc62a3e6 x22: ffffff80c6c07000 x21: ffffffdbdc829290
<4>[ 29.158219] x20: 0000000000000000 x19: ffffff80cd3e0648 x18: 000000031ec97781
<4>[ 29.158229] x17: ffffff80c1bdc4a8 x16: ffffffdc10576548 x15: ffffff80c1180428
<4>[ 29.158238] x14: 0000000000000000 x13: 000000000000e380 x12: 0000000000000018
<4>[ 29.158248] x11: ffffff80c2a7fd10 x10: 0000000000000000 x9 : 0000000100000000
<4>[ 29.158257] x8 : 0000000000000000 x7 : 7f7f7f7f7f7f7f7f x6 : 2d7223ff6364626d
<4>[ 29.158266] x5 : 0000008000000000 x4 : 0000000000000020 x3 : 2e7325006465636e
<4>[ 29.158275] x2 : ffffffdc11afeff8 x1 : 0000000000000000 x0 : ffffffdc11be4d0c
<4>[ 29.158285] Call trace:
<4>[ 29.158290] klist_remove+0x90/0x158
<4>[ 29.158298] device_release_driver_internal+0x20c/0x268
<4>[ 29.158308] device_release_driver+0x1c/0x30
<4>[ 29.158316] usb_driver_release_interface+0x70/0x88
<4>[ 29.158325] btusb_mtk_release_iso_intf+0x68/0xd8 [btusb (HASH:e8b6 5)]
<4>[ 29.158347] btusb_mtk_reset+0x5c/0x480 [btusb (HASH:e8b6 5)]
<4>[ 29.158361] hci_cmd_sync_work+0x10c/0x188 [bluetooth (HASH:a4fa 6)]
<4>[ 29.158430] process_scheduled_works+0x258/0x4e8
<4>[ 29.158441] worker_thread+0x300/0x428
<4>[ 29.158448] kthread+0x108/0x1d0
<4>[ 29.158455] ret_from_fork+0x10/0x20
<0>[ 29.158467] Code: 91343000 940139d1 f9400268 927ff914 (f9401297)
<4>[ 29.158474] ---[ end trace 0000000000000000 ]---
<0>[ 29.167129] Kernel panic - not syncing: Oops: Fatal exception
<2>[ 29.167144] SMP: stopping secondary CPUs
<4>[ 29.167158] ------------[ cut here ]------------ |
| In the Linux kernel, the following vulnerability has been resolved:
can: kvaser_usb: leaf: Fix potential infinite loop in command parsers
The `kvaser_usb_leaf_wait_cmd()` and `kvaser_usb_leaf_read_bulk_callback`
functions contain logic to zero-length commands. These commands are used
to align data to the USB endpoint's wMaxPacketSize boundary.
The driver attempts to skip these placeholders by aligning the buffer
position `pos` to the next packet boundary using `round_up()` function.
However, if zero-length command is found exactly on a packet boundary
(i.e., `pos` is a multiple of wMaxPacketSize, including 0), `round_up`
function will return the unchanged value of `pos`. This prevents `pos`
to be increased, causing an infinite loop in the parsing logic.
This patch fixes this in the function by using `pos + 1` instead.
This ensures that even if `pos` is on a boundary, the calculation is
based on `pos + 1`, forcing `round_up()` to always return the next
aligned boundary. |
| In the Linux kernel, the following vulnerability has been resolved:
block: fix memory leak in __blkdev_issue_zero_pages
Move the fatal signal check before bio_alloc() to prevent a memory
leak when BLKDEV_ZERO_KILLABLE is set and a fatal signal is pending.
Previously, the bio was allocated before checking for a fatal signal.
If a signal was pending, the code would break out of the loop without
freeing or chaining the just-allocated bio, causing a memory leak.
This matches the pattern already used in __blkdev_issue_write_zeroes()
where the signal check precedes the allocation. |
