| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| A flaw was found in AMQ Broker. This issue can cause a partial interruption to the availability of AMQ Broker via an Out of memory (OOM) condition. This flaw allows an attacker to partially disrupt availability to the broker through a sustained attack of maliciously crafted messages. The highest threat from this vulnerability is system availability. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath5k: do not access array OOB
Vincent reports:
> The ath5k driver seems to do an array-index-out-of-bounds access as
> shown by the UBSAN kernel message:
> UBSAN: array-index-out-of-bounds in drivers/net/wireless/ath/ath5k/base.c:1741:20
> index 4 is out of range for type 'ieee80211_tx_rate [4]'
> ...
> Call Trace:
> <TASK>
> dump_stack_lvl+0x5d/0x80
> ubsan_epilogue+0x5/0x2b
> __ubsan_handle_out_of_bounds.cold+0x46/0x4b
> ath5k_tasklet_tx+0x4e0/0x560 [ath5k]
> tasklet_action_common+0xb5/0x1c0
It is real. 'ts->ts_final_idx' can be 3 on 5212, so:
info->status.rates[ts->ts_final_idx + 1].idx = -1;
with the array defined as:
struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
while the size is:
#define IEEE80211_TX_MAX_RATES 4
is indeed bogus.
Set this 'idx = -1' sentinel only if the array index is less than the
array size. As mac80211 will not look at rates beyond the size
(IEEE80211_TX_MAX_RATES).
Note: The effect of the OOB write is negligible. It just overwrites the
next member of info->status, i.e. ack_signal. |
| Out-of-bounds write in Windows Hotpatch Monitoring Service allows an authorized attacker to elevate privileges locally. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rsi: Fix memory corruption due to not set vif driver data size
The struct ieee80211_vif contains trailing space for vif driver data,
when struct ieee80211_vif is allocated, the total memory size that is
allocated is sizeof(struct ieee80211_vif) + size of vif driver data.
The size of vif driver data is set by each WiFi driver as needed.
The RSI911x driver does not set vif driver data size, no trailing space
for vif driver data is therefore allocated past struct ieee80211_vif .
The RSI911x driver does however use the vif driver data to store its
vif driver data structure "struct vif_priv". An access to vif->drv_priv
leads to access out of struct ieee80211_vif bounds and corruption of
some memory.
In case of the failure observed locally, rsi_mac80211_add_interface()
would write struct vif_priv *vif_info = (struct vif_priv *)vif->drv_priv;
vif_info->vap_id = vap_idx. This write corrupts struct fq_tin member
struct list_head new_flows . The flow = list_first_entry(head, struct
fq_flow, flowchain); in fq_tin_reset() then reports non-NULL bogus
address, which when accessed causes a crash.
The trigger is very simple, boot the machine with init=/bin/sh , mount
devtmpfs, sysfs, procfs, and then do "ip link set wlan0 up", "sleep 1",
"ip link set wlan0 down" and the crash occurs.
Fix this by setting the correct size of vif driver data, which is the
size of "struct vif_priv", so that memory is allocated and the driver
can store its driver data in it, instead of corrupting memory around
it. |
| In the Linux kernel, the following vulnerability has been resolved:
atm: clip: Fix infinite recursive call of clip_push().
syzbot reported the splat below. [0]
This happens if we call ioctl(ATMARP_MKIP) more than once.
During the first call, clip_mkip() sets clip_push() to vcc->push(),
and the second call copies it to clip_vcc->old_push().
Later, when the socket is close()d, vcc_destroy_socket() passes
NULL skb to clip_push(), which calls clip_vcc->old_push(),
triggering the infinite recursion.
Let's prevent the second ioctl(ATMARP_MKIP) by checking
vcc->user_back, which is allocated by the first call as clip_vcc.
Note also that we use lock_sock() to prevent racy calls.
[0]:
BUG: TASK stack guard page was hit at ffffc9000d66fff8 (stack is ffffc9000d670000..ffffc9000d678000)
Oops: stack guard page: 0000 [#1] SMP KASAN NOPTI
CPU: 0 UID: 0 PID: 5322 Comm: syz.0.0 Not tainted 6.16.0-rc4-syzkaller #0 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
RIP: 0010:clip_push+0x5/0x720 net/atm/clip.c:191
Code: e0 8f aa 8c e8 1c ad 5b fa eb ae 66 2e 0f 1f 84 00 00 00 00 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 0f 1e fa 55 <41> 57 41 56 41 55 41 54 53 48 83 ec 20 48 89 f3 49 89 fd 48 bd 00
RSP: 0018:ffffc9000d670000 EFLAGS: 00010246
RAX: 1ffff1100235a4a5 RBX: ffff888011ad2508 RCX: ffff8880003c0000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff888037f01000
RBP: dffffc0000000000 R08: ffffffff8fa104f7 R09: 1ffffffff1f4209e
R10: dffffc0000000000 R11: ffffffff8a99b300 R12: ffffffff8a99b300
R13: ffff888037f01000 R14: ffff888011ad2500 R15: ffff888037f01578
FS: 000055557ab6d500(0000) GS:ffff88808d250000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffc9000d66fff8 CR3: 0000000043172000 CR4: 0000000000352ef0
Call Trace:
<TASK>
clip_push+0x6dc/0x720 net/atm/clip.c:200
clip_push+0x6dc/0x720 net/atm/clip.c:200
clip_push+0x6dc/0x720 net/atm/clip.c:200
...
clip_push+0x6dc/0x720 net/atm/clip.c:200
clip_push+0x6dc/0x720 net/atm/clip.c:200
clip_push+0x6dc/0x720 net/atm/clip.c:200
vcc_destroy_socket net/atm/common.c:183 [inline]
vcc_release+0x157/0x460 net/atm/common.c:205
__sock_release net/socket.c:647 [inline]
sock_close+0xc0/0x240 net/socket.c:1391
__fput+0x449/0xa70 fs/file_table.c:465
task_work_run+0x1d1/0x260 kernel/task_work.c:227
resume_user_mode_work include/linux/resume_user_mode.h:50 [inline]
exit_to_user_mode_loop+0xec/0x110 kernel/entry/common.c:114
exit_to_user_mode_prepare include/linux/entry-common.h:330 [inline]
syscall_exit_to_user_mode_work include/linux/entry-common.h:414 [inline]
syscall_exit_to_user_mode include/linux/entry-common.h:449 [inline]
do_syscall_64+0x2bd/0x3b0 arch/x86/entry/syscall_64.c:100
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7ff31c98e929
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fffb5aa1f78 EFLAGS: 00000246 ORIG_RAX: 00000000000001b4
RAX: 0000000000000000 RBX: 0000000000012747 RCX: 00007ff31c98e929
RDX: 0000000000000000 RSI: 000000000000001e RDI: 0000000000000003
RBP: 00007ff31cbb7ba0 R08: 0000000000000001 R09: 0000000db5aa226f
R10: 00007ff31c7ff030 R11: 0000000000000246 R12: 00007ff31cbb608c
R13: 00007ff31cbb6080 R14: ffffffffffffffff R15: 00007fffb5aa2090
</TASK>
Modules linked in: |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mana: Validate rx_hash_key_len
Sashiko points out that rx_hash_key_len comes from a uAPI structure and is
blindly passed to memcpy, allowing the userspace to trash kernel
memory. Bounds check it so the memcpy cannot overflow. |
| In the Linux kernel, the following vulnerability has been resolved:
vsock: fix buffer size clamping order
In vsock_update_buffer_size(), the buffer size was being clamped to the
maximum first, and then to the minimum. If a user sets a minimum buffer
size larger than the maximum, the minimum check overrides the maximum
check, inverting the constraint.
This breaks the intended socket memory boundaries by allowing the
vsk->buffer_size to grow beyond the configured vsk->buffer_max_size.
Fix this by checking the minimum first, and then the maximum. This
ensures the buffer size never exceeds the buffer_max_size. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/gem: Fix inconsistent plane dimension calculation in drm_gem_fb_init_with_funcs()
drm_gem_fb_init_with_funcs() computes sub-sampled plane dimensions
using plain integer division:
unsigned int width = mode_cmd->width / (i ? info->hsub : 1);
unsigned int height = mode_cmd->height / (i ? info->vsub : 1);
However, the ioctl-level framebuffer_check() in drm_framebuffer.c uses
drm_format_info_plane_width/height() which round up dimensions via
DIV_ROUND_UP(). This inconsistency corrupts the subsequent GEM object
size check for certain pixel format and dimension combinations.
For example, with NV12 (vsub=2) and a 1-pixel-tall framebuffer the
GEM size validation path sees height=0 instead of height=1. The
expression (height - 1) then wraps to UINT_MAX as an unsigned int,
causing min_size to overflow and wrap back to a small value. A tiny
GEM object therefore passes the size guard, yet when the GPU accesses
the chroma plane it will read or write memory beyond the object's
bounds.
Fix by replacing the open-coded divisions with drm_format_info_plane_width()
and drm_format_info_plane_height(), which use DIV_ROUND_UP() and match
the calculation already used in framebuffer_check(). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: validate SVM ioctl nattr against buffer size
Validate nattr field against the buffer size, preventing
out-of-bounds buffer access via user-controlled attribute count.
(cherry picked from commit 5eca8bfdfa456c3304ca77523718fe24254c172f) |
| In the Linux kernel, the following vulnerability has been resolved:
pstore/ram: fix buffer overflow in persistent_ram_save_old()
persistent_ram_save_old() can be called multiple times for the same
persistent_ram_zone (e.g., via ramoops_pstore_read -> ramoops_get_next_prz
for PSTORE_TYPE_DMESG records).
Currently, the function only allocates prz->old_log when it is NULL,
but it unconditionally updates prz->old_log_size to the current buffer
size and then performs memcpy_fromio() using this new size. If the
buffer size has grown since the first allocation (which can happen
across different kernel boot cycles), this leads to:
1. A heap buffer overflow (OOB write) in the memcpy_fromio() calls
2. A subsequent OOB read when ramoops_pstore_read() accesses the buffer
using the incorrect (larger) old_log_size
The KASAN splat would look similar to:
BUG: KASAN: slab-out-of-bounds in ramoops_pstore_read+0x...
Read of size N at addr ... by task ...
The conditions are likely extremely hard to hit:
0. Crash with a ramoops write of less-than-record-max-size bytes.
1. Reboot: ramoops registers, pstore_get_records(0) reads old crash,
allocates old_log with size X
2. Crash handler registered, timer started (if pstore_update_ms >= 0)
3. Oops happens (non-fatal, system continues)
4. pstore_dump() writes oops via ramoops_pstore_write() size Y (>X)
5. pstore_new_entry = 1, pstore_timer_kick() called
6. System continues running (not a panic oops)
7. Timer fires after pstore_update_ms milliseconds
8. pstore_timefunc() → schedule_work() → pstore_dowork() → pstore_get_records(1)
9. ramoops_get_next_prz() → persistent_ram_save_old()
10. buffer_size() returns Y, but old_log is X bytes
11. Y > X: memcpy_fromio() overflows heap
Requirements:
- a prior crash record exists that did not fill the record size
(almost impossible since the crash handler writes as much as it
can possibly fit into the record, capped by max record size and
the kmsg buffer almost always exceeds the max record size)
- pstore_update_ms >= 0 (disabled by default)
- Non-fatal oops (system survives)
Free and reallocate the buffer when the new size differs from the
previously allocated size. This ensures old_log always has sufficient
space for the data being copied. |
| Issue summary: Parsing CMS AuthEnvelopedData or EnvelopedData message with
maliciously crafted AEAD parameters can trigger a stack buffer overflow.
Impact summary: A stack buffer overflow may lead to a crash, causing Denial
of Service, or potentially remote code execution.
When parsing CMS (Auth)EnvelopedData structures that use AEAD ciphers such as
AES-GCM, the IV (Initialization Vector) encoded in the ASN.1 parameters is
copied into a fixed-size stack buffer without verifying that its length fits
the destination. An attacker can supply a crafted CMS message with an
oversized IV, causing a stack-based out-of-bounds write before any
authentication or tag verification occurs.
Applications and services that parse untrusted CMS or PKCS#7 content using
AEAD ciphers (e.g., S/MIME (Auth)EnvelopedData with AES-GCM) are vulnerable.
Because the overflow occurs prior to authentication, no valid key material
is required to trigger it. While exploitability to remote code execution
depends on platform and toolchain mitigations, the stack-based write
primitive represents a severe risk.
The FIPS modules in 3.6, 3.5, 3.4, 3.3 and 3.0 are not affected by this
issue, as the CMS implementation is outside the OpenSSL FIPS module
boundary.
OpenSSL 3.6, 3.5, 3.4, 3.3 and 3.0 are vulnerable to this issue.
OpenSSL 1.1.1 and 1.0.2 are not affected by this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
dm: fix a buffer overflow in ioctl processing
Tony Asleson (using Claude) found a buffer overflow in dm-ioctl in the
function retrieve_status:
1. The code in retrieve_status checks that the output string fits into
the output buffer and writes the output string there
2. Then, the code aligns the "outptr" variable to the next 8-byte
boundary:
outptr = align_ptr(outptr);
3. The alignment doesn't check overflow, so outptr could point past the
buffer end
4. The "for" loop is iterated again, it executes:
remaining = len - (outptr - outbuf);
5. If "outptr" points past "outbuf + len", the arithmetics wraps around
and the variable "remaining" contains unusually high number
6. With "remaining" being high, the code writes more data past the end of
the buffer
Luckily, this bug has no security implications because:
1. Only root can issue device mapper ioctls
2. The commonly used libraries that communicate with device mapper
(libdevmapper and devicemapper-rs) use buffer size that is aligned to
8 bytes - thus, "outptr = align_ptr(outptr)" can't overshoot the input
buffer and the bug can't happen accidentally |
| Linaro/OP-TEE OP-TEE Prior to version v3.4.0 is affected by: Boundary checks. The impact is: This could lead to corruption of any memory which the TA can access. The component is: optee_os. The fixed version is: v3.4.0. |
| Linaro/OP-TEE OP-TEE 3.3.0 and earlier is affected by: Buffer Overflow. The impact is: Code execution in the context of TEE core (kernel). The component is: optee_os. The fixed version is: 3.4.0 and later. |
| Linaro/OP-TEE OP-TEE 3.3.0 and earlier is affected by: Buffer Overflow. The impact is: Execution of code in TEE core (kernel) context. The component is: optee_os. The fixed version is: 3.4.0 and later. |
| Linaro/OP-TEE OP-TEE 3.3.0 and earlier is affected by: Buffer Overflow. The impact is: Code execution in context of TEE core (kernel). The component is: optee_os. The fixed version is: 3.4.0 and later. |
| Linaro/OP-TEE OP-TEE 3.3.0 and earlier is affected by: Boundary crossing. The impact is: Memory corruption of the TEE itself. The component is: optee_os. The fixed version is: 3.4.0 and later. |
| Linaro/OP-TEE OP-TEE 3.3.0 and earlier is affected by: Buffer Overflow. The impact is: Memory corruption and disclosure of memory content. The component is: optee_os. The fixed version is: 3.4.0 and later. |
| Out-of-bounds write vulnerability in Samsung Open Source Escargot allows Overflow Buffers.
This issue affects Escargot: 36f5fb58366a67b713c02f6fd985e924fcc09e31. |
| A stack-based buffer overflow vulnerability was found inside ADM when using WebDAV due to the lack of data size validation. An attacker can exploit this vulnerability to run arbitrary code. Affected ADM versions include: 3.5.9.RUE3 and below, 4.0.5.RVI1 and below as well as 4.1.0.RJD1 and below. |
