| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: wan: farsync: Fix use-after-free bugs caused by unfinished tasklets
When the FarSync T-series card is being detached, the fst_card_info is
deallocated in fst_remove_one(). However, the fst_tx_task or fst_int_task
may still be running or pending, leading to use-after-free bugs when the
already freed fst_card_info is accessed in fst_process_tx_work_q() or
fst_process_int_work_q().
A typical race condition is depicted below:
CPU 0 (cleanup) | CPU 1 (tasklet)
| fst_start_xmit()
fst_remove_one() | tasklet_schedule()
unregister_hdlc_device()|
| fst_process_tx_work_q() //handler
kfree(card) //free | do_bottom_half_tx()
| card-> //use
The following KASAN trace was captured:
==================================================================
BUG: KASAN: slab-use-after-free in do_bottom_half_tx+0xb88/0xd00
Read of size 4 at addr ffff88800aad101c by task ksoftirqd/3/32
...
Call Trace:
<IRQ>
dump_stack_lvl+0x55/0x70
print_report+0xcb/0x5d0
? do_bottom_half_tx+0xb88/0xd00
kasan_report+0xb8/0xf0
? do_bottom_half_tx+0xb88/0xd00
do_bottom_half_tx+0xb88/0xd00
? _raw_spin_lock_irqsave+0x85/0xe0
? __pfx__raw_spin_lock_irqsave+0x10/0x10
? __pfx___hrtimer_run_queues+0x10/0x10
fst_process_tx_work_q+0x67/0x90
tasklet_action_common+0x1fa/0x720
? hrtimer_interrupt+0x31f/0x780
handle_softirqs+0x176/0x530
__irq_exit_rcu+0xab/0xe0
sysvec_apic_timer_interrupt+0x70/0x80
...
Allocated by task 41 on cpu 3 at 72.330843s:
kasan_save_stack+0x24/0x50
kasan_save_track+0x17/0x60
__kasan_kmalloc+0x7f/0x90
fst_add_one+0x1a5/0x1cd0
local_pci_probe+0xdd/0x190
pci_device_probe+0x341/0x480
really_probe+0x1c6/0x6a0
__driver_probe_device+0x248/0x310
driver_probe_device+0x48/0x210
__device_attach_driver+0x160/0x320
bus_for_each_drv+0x101/0x190
__device_attach+0x198/0x3a0
device_initial_probe+0x78/0xa0
pci_bus_add_device+0x81/0xc0
pci_bus_add_devices+0x7e/0x190
enable_slot+0x9b9/0x1130
acpiphp_check_bridge.part.0+0x2e1/0x460
acpiphp_hotplug_notify+0x36c/0x3c0
acpi_device_hotplug+0x203/0xb10
acpi_hotplug_work_fn+0x59/0x80
...
Freed by task 41 on cpu 1 at 75.138639s:
kasan_save_stack+0x24/0x50
kasan_save_track+0x17/0x60
kasan_save_free_info+0x3b/0x60
__kasan_slab_free+0x43/0x70
kfree+0x135/0x410
fst_remove_one+0x2ca/0x540
pci_device_remove+0xa6/0x1d0
device_release_driver_internal+0x364/0x530
pci_stop_bus_device+0x105/0x150
pci_stop_and_remove_bus_device+0xd/0x20
disable_slot+0x116/0x260
acpiphp_disable_and_eject_slot+0x4b/0x190
acpiphp_hotplug_notify+0x230/0x3c0
acpi_device_hotplug+0x203/0xb10
acpi_hotplug_work_fn+0x59/0x80
...
The buggy address belongs to the object at ffff88800aad1000
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 28 bytes inside of
freed 1024-byte region
The buggy address belongs to the physical page:
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0xaad0
head: order:3 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0
flags: 0x100000000000040(head|node=0|zone=1)
page_type: f5(slab)
raw: 0100000000000040 ffff888007042dc0 dead000000000122 0000000000000000
raw: 0000000000000000 0000000080100010 00000000f5000000 0000000000000000
head: 0100000000000040 ffff888007042dc0 dead000000000122 0000000000000000
head: 0000000000000000 0000000080100010 00000000f5000000 0000000000000000
head: 0100000000000003 ffffea00002ab401 00000000ffffffff 00000000ffffffff
head: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88800aad0f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88800aad0f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88800aad1000: fa fb
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
padata: Fix possible divide-by-0 panic in padata_mt_helper()
We are hit with a not easily reproducible divide-by-0 panic in padata.c at
bootup time.
[ 10.017908] Oops: divide error: 0000 1 PREEMPT SMP NOPTI
[ 10.017908] CPU: 26 PID: 2627 Comm: kworker/u1666:1 Not tainted 6.10.0-15.el10.x86_64 #1
[ 10.017908] Hardware name: Lenovo ThinkSystem SR950 [7X12CTO1WW]/[7X12CTO1WW], BIOS [PSE140J-2.30] 07/20/2021
[ 10.017908] Workqueue: events_unbound padata_mt_helper
[ 10.017908] RIP: 0010:padata_mt_helper+0x39/0xb0
:
[ 10.017963] Call Trace:
[ 10.017968] <TASK>
[ 10.018004] ? padata_mt_helper+0x39/0xb0
[ 10.018084] process_one_work+0x174/0x330
[ 10.018093] worker_thread+0x266/0x3a0
[ 10.018111] kthread+0xcf/0x100
[ 10.018124] ret_from_fork+0x31/0x50
[ 10.018138] ret_from_fork_asm+0x1a/0x30
[ 10.018147] </TASK>
Looking at the padata_mt_helper() function, the only way a divide-by-0
panic can happen is when ps->chunk_size is 0. The way that chunk_size is
initialized in padata_do_multithreaded(), chunk_size can be 0 when the
min_chunk in the passed-in padata_mt_job structure is 0.
Fix this divide-by-0 panic by making sure that chunk_size will be at least
1 no matter what the input parameters are. |
| In the Linux kernel, the following vulnerability has been resolved:
media: ccs: Avoid possible division by zero
Calculating maximum M for scaler configuration involves dividing by
MIN_X_OUTPUT_SIZE limit register's value. Albeit the value is presumably
non-zero, the driver was missing the check it in fact was. Fix this. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: fix potential race in tcp_v6_syn_recv_sock()
Code in tcp_v6_syn_recv_sock() after the call to tcp_v4_syn_recv_sock()
is done too late.
After tcp_v4_syn_recv_sock(), the child socket is already visible
from TCP ehash table and other cpus might use it.
Since newinet->pinet6 is still pointing to the listener ipv6_pinfo
bad things can happen as syzbot found.
Move the problematic code in tcp_v6_mapped_child_init()
and call this new helper from tcp_v4_syn_recv_sock() before
the ehash insertion.
This allows the removal of one tcp_sync_mss(), since
tcp_v4_syn_recv_sock() will call it with the correct
context. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (occ) Fix division by zero in occ_show_power_1()
In occ_show_power_1() case 1, the accumulator is divided by
update_tag without checking for zero. If no samples have been
collected yet (e.g. during early boot when the sensor block is
included but hasn't been updated), update_tag is zero, causing
a kernel divide-by-zero crash.
The 2019 fix in commit 211186cae14d ("hwmon: (occ) Fix division by
zero issue") only addressed occ_get_powr_avg() used by
occ_show_power_2() and occ_show_power_a0(). This separate code
path in occ_show_power_1() was missed.
Fix this by reusing the existing occ_get_powr_avg() helper, which
already handles the zero-sample case and uses mul_u64_u32_div()
to multiply before dividing for better precision. Move the helper
above occ_show_power_1() so it is visible at the call site.
[groeck: Fix alignment problems reported by checkpatch] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915/dsi: Don't do DSC horizontal timing adjustments in command mode
Stop adjusting the horizontal timing values based on the
compression ratio in command mode. Bspec seems to be telling
us to do this only in video mode, and this is also how the
Windows driver does things.
This should also fix a div-by-zero on some machines because
the adjusted htotal ends up being so small that we end up with
line_time_us==0 when trying to determine the vtotal value in
command mode.
Note that this doesn't actually make the display on the
Huawei Matebook E work, but at least the kernel no longer
explodes when the driver loads.
(cherry picked from commit 0b475e91ecc2313207196c6d7fd5c53e1a878525) |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: core: Flush exception handling work when RPM level is zero
Ensure that the exception event handling work is explicitly flushed during
suspend when the runtime power management level is set to UFS_PM_LVL_0.
When the RPM level is zero, the device power mode and link state both
remain active. Previously, the UFS core driver bypassed flushing exception
event handling jobs in this configuration. This created a race condition
where the driver could attempt to access the host controller to handle an
exception after the system had already entered a deep power-down state,
resulting in a system crash.
Explicitly flush this work and disable auto BKOPs before the suspend
callback proceeds. This guarantees that pending exception tasks complete
and prevents illegal hardware access during the power-down sequence. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: gyro: mpu3050: Move iio_device_register() to correct location
iio_device_register() should be at the end of the probe function to
prevent race conditions.
Place iio_device_register() at the end of the probe function and place
iio_device_unregister() accordingly. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Flush dev-IOTLB only when PCIe device is accessible in scalable mode
Commit 4fc82cd907ac ("iommu/vt-d: Don't issue ATS Invalidation
request when device is disconnected") relies on
pci_dev_is_disconnected() to skip ATS invalidation for
safely-removed devices, but it does not cover link-down caused
by faults, which can still hard-lock the system.
For example, if a VM fails to connect to the PCIe device,
"virsh destroy" is executed to release resources and isolate
the fault, but a hard-lockup occurs while releasing the group fd.
Call Trace:
qi_submit_sync
qi_flush_dev_iotlb
intel_pasid_tear_down_entry
device_block_translation
blocking_domain_attach_dev
__iommu_attach_device
__iommu_device_set_domain
__iommu_group_set_domain_internal
iommu_detach_group
vfio_iommu_type1_detach_group
vfio_group_detach_container
vfio_group_fops_release
__fput
Although pci_device_is_present() is slower than
pci_dev_is_disconnected(), it still takes only ~70 µs on a
ConnectX-5 (8 GT/s, x2) and becomes even faster as PCIe speed
and width increase.
Besides, devtlb_invalidation_with_pasid() is called only in the
paths below, which are far less frequent than memory map/unmap.
1. mm-struct release
2. {attach,release}_dev
3. set/remove PASID
4. dirty-tracking setup
The gain in system stability far outweighs the negligible cost
of using pci_device_is_present() instead of pci_dev_is_disconnected()
to decide when to skip ATS invalidation, especially under GDR
high-load conditions. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: SCO: fix race conditions in sco_sock_connect()
sco_sock_connect() checks sk_state and sk_type without holding
the socket lock. Two concurrent connect() syscalls on the same
socket can both pass the check and enter sco_connect(), leading
to use-after-free.
The buggy scenario involves three participants and was confirmed
with additional logging instrumentation:
Thread A (connect): HCI disconnect: Thread B (connect):
sco_sock_connect(sk) sco_sock_connect(sk)
sk_state==BT_OPEN sk_state==BT_OPEN
(pass, no lock) (pass, no lock)
sco_connect(sk): sco_connect(sk):
hci_dev_lock hci_dev_lock
hci_connect_sco <- blocked
-> hcon1
sco_conn_add->conn1
lock_sock(sk)
sco_chan_add:
conn1->sk = sk
sk->conn = conn1
sk_state=BT_CONNECT
release_sock
hci_dev_unlock
hci_dev_lock
sco_conn_del:
lock_sock(sk)
sco_chan_del:
sk->conn=NULL
conn1->sk=NULL
sk_state=
BT_CLOSED
SOCK_ZAPPED
release_sock
hci_dev_unlock
(unblocked)
hci_connect_sco
-> hcon2
sco_conn_add
-> conn2
lock_sock(sk)
sco_chan_add:
sk->conn=conn2
sk_state=
BT_CONNECT
// zombie sk!
release_sock
hci_dev_unlock
Thread B revives a BT_CLOSED + SOCK_ZAPPED socket back to
BT_CONNECT. Subsequent cleanup triggers double sock_put() and
use-after-free. Meanwhile conn1 is leaked as it was orphaned
when sco_conn_del() cleared the association.
Fix this by:
- Moving lock_sock() before the sk_state/sk_type checks in
sco_sock_connect() to serialize concurrent connect attempts
- Fixing the sk_type != SOCK_SEQPACKET check to actually
return the error instead of just assigning it
- Adding a state re-check in sco_connect() after lock_sock()
to catch state changes during the window between the locks
- Adding sco_pi(sk)->conn check in sco_chan_add() to prevent
double-attach of a socket to multiple connections
- Adding hci_conn_drop() on sco_chan_add failure to prevent
HCI connection leaks |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: dt2815: add hardware detection to prevent crash
The dt2815 driver crashes when attached to I/O ports without actual
hardware present. This occurs because syzkaller or users can attach
the driver to arbitrary I/O addresses via COMEDI_DEVCONFIG ioctl.
When no hardware exists at the specified port, inb() operations return
0xff (floating bus), but outb() operations can trigger page faults due
to undefined behavior, especially under race conditions:
BUG: unable to handle page fault for address: 000000007fffff90
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
RIP: 0010:dt2815_attach+0x6e0/0x1110
Add hardware detection by reading the status register before attempting
any write operations. If the read returns 0xff, assume no hardware is
present and fail the attach with -ENODEV. This prevents crashes from
outb() operations on non-existent hardware. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/huge_memory: fix folio isn't locked in softleaf_to_folio()
On arm64 server, we found folio that get from migration entry isn't locked
in softleaf_to_folio(). This issue triggers when mTHP splitting and
zap_nonpresent_ptes() races, and the root cause is lack of memory barrier
in softleaf_to_folio(). The race is as follows:
CPU0 CPU1
deferred_split_scan() zap_nonpresent_ptes()
lock folio
split_folio()
unmap_folio()
change ptes to migration entries
__split_folio_to_order() softleaf_to_folio()
set flags(including PG_locked) for tail pages folio = pfn_folio(softleaf_to_pfn(entry))
smp_wmb() VM_WARN_ON_ONCE(!folio_test_locked(folio))
prep_compound_page() for tail pages
In __split_folio_to_order(), smp_wmb() guarantees page flags of tail pages
are visible before the tail page becomes non-compound. smp_wmb() should
be paired with smp_rmb() in softleaf_to_folio(), which is missed. As a
result, if zap_nonpresent_ptes() accesses migration entry that stores tail
pfn, softleaf_to_folio() may see the updated compound_head of tail page
before page->flags.
This issue will trigger VM_WARN_ON_ONCE() in pfn_swap_entry_folio()
because of the race between folio split and zap_nonpresent_ptes()
leading to a folio incorrectly undergoing modification without a folio
lock being held.
This is a BUG_ON() before commit 93976a20345b ("mm: eliminate further
swapops predicates"), which in merged in v6.19-rc1.
To fix it, add missing smp_rmb() if the softleaf entry is migration entry
in softleaf_to_folio() and softleaf_to_page().
[tujinjiang@huawei.com: update function name and comments] |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: uvc: fix NULL pointer dereference during unbind race
Commit b81ac4395bbe ("usb: gadget: uvc: allow for application to cleanly
shutdown") introduced two stages of synchronization waits totaling 1500ms
in uvc_function_unbind() to prevent several types of kernel panics.
However, this timing-based approach is insufficient during power
management (PM) transitions.
When the PM subsystem starts freezing user space processes, the
wait_event_interruptible_timeout() is aborted early, which allows the
unbind thread to proceed and nullify the gadget pointer
(cdev->gadget = NULL):
[ 814.123447][ T947] configfs-gadget.g1 gadget.0: uvc: uvc_function_unbind()
[ 814.178583][ T3173] PM: suspend entry (deep)
[ 814.192487][ T3173] Freezing user space processes
[ 814.197668][ T947] configfs-gadget.g1 gadget.0: uvc: uvc_function_unbind no clean disconnect, wait for release
When the PM subsystem resumes or aborts the suspend and tasks are
restarted, the V4L2 release path is executed and attempts to access the
already nullified gadget pointer, triggering a kernel panic:
[ 814.292597][ C0] PM: pm_system_irq_wakeup: 479 triggered dhdpcie_host_wake
[ 814.386727][ T3173] Restarting tasks ...
[ 814.403522][ T4558] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000030
[ 814.404021][ T4558] pc : usb_gadget_deactivate+0x14/0xf4
[ 814.404031][ T4558] lr : usb_function_deactivate+0x54/0x94
[ 814.404078][ T4558] Call trace:
[ 814.404080][ T4558] usb_gadget_deactivate+0x14/0xf4
[ 814.404083][ T4558] usb_function_deactivate+0x54/0x94
[ 814.404087][ T4558] uvc_function_disconnect+0x1c/0x5c
[ 814.404092][ T4558] uvc_v4l2_release+0x44/0xac
[ 814.404095][ T4558] v4l2_release+0xcc/0x130
Address the race condition and NULL pointer dereference by:
1. State Synchronization (flag + mutex)
Introduce a 'func_unbound' flag in struct uvc_device. This allows
uvc_function_disconnect() to safely skip accessing the nullified
cdev->gadget pointer. As suggested by Alan Stern, this flag is protected
by a new mutex (uvc->lock) to ensure proper memory ordering and prevent
instruction reordering or speculative loads. This mutex is also used to
protect 'func_connected' for consistent state management.
2. Explicit Synchronization (completion)
Use a completion to synchronize uvc_function_unbind() with the
uvc_vdev_release() callback. This prevents Use-After-Free (UAF) by
ensuring struct uvc_device is freed after all video device resources
are released. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: u_ether: Fix race between gether_disconnect and eth_stop
A race condition between gether_disconnect() and eth_stop() leads to a
NULL pointer dereference. Specifically, if eth_stop() is triggered
concurrently while gether_disconnect() is tearing down the endpoints,
eth_stop() attempts to access the cleared endpoint descriptor, causing
the following NPE:
Unable to handle kernel NULL pointer dereference
Call trace:
__dwc3_gadget_ep_enable+0x60/0x788
dwc3_gadget_ep_enable+0x70/0xe4
usb_ep_enable+0x60/0x15c
eth_stop+0xb8/0x108
Because eth_stop() crashes while holding the dev->lock, the thread
running gether_disconnect() fails to acquire the same lock and spins
forever, resulting in a hardlockup:
Core - Debugging Information for Hardlockup core(7)
Call trace:
queued_spin_lock_slowpath+0x94/0x488
_raw_spin_lock+0x64/0x6c
gether_disconnect+0x19c/0x1e8
ncm_set_alt+0x68/0x1a0
composite_setup+0x6a0/0xc50
The root cause is that the clearing of dev->port_usb in
gether_disconnect() is delayed until the end of the function.
Move the clearing of dev->port_usb to the very beginning of
gether_disconnect() while holding dev->lock. This cuts off the link
immediately, ensuring eth_stop() will see dev->port_usb as NULL and
safely bail out. |
| In the Linux kernel, the following vulnerability has been resolved:
openvswitch: defer tunnel netdev_put to RCU release
ovs_netdev_tunnel_destroy() may run after NETDEV_UNREGISTER already
detached the device. Dropping the netdev reference in destroy can race
with concurrent readers that still observe vport->dev.
Do not release vport->dev in ovs_netdev_tunnel_destroy(). Instead, let
vport_netdev_free() drop the reference from the RCU callback, matching
the non-tunnel destroy path and avoiding additional synchronization
under RTNL. |
| OpenClaw before 2026.4.4 contains a race condition vulnerability in shared-secret authentication that allows concurrent asynchronous requests to bypass the per-key rate-limit budget. Attackers can exploit this by sending multiple simultaneous authentication attempts to circumvent intended rate-limiting protections on Tailscale-capable paths. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: set BTRFS_ROOT_ORPHAN_CLEANUP during subvol create
We have recently observed a number of subvolumes with broken dentries.
ls-ing the parent dir looks like:
drwxrwxrwt 1 root root 16 Jan 23 16:49 .
drwxr-xr-x 1 root root 24 Jan 23 16:48 ..
d????????? ? ? ? ? ? broken_subvol
and similarly stat-ing the file fails.
In this state, deleting the subvol fails with ENOENT, but attempting to
create a new file or subvol over it errors out with EEXIST and even
aborts the fs. Which leaves us a bit stuck.
dmesg contains a single notable error message reading:
"could not do orphan cleanup -2"
2 is ENOENT and the error comes from the failure handling path of
btrfs_orphan_cleanup(), with the stack leading back up to
btrfs_lookup().
btrfs_lookup
btrfs_lookup_dentry
btrfs_orphan_cleanup // prints that message and returns -ENOENT
After some detailed inspection of the internal state, it became clear
that:
- there are no orphan items for the subvol
- the subvol is otherwise healthy looking, it is not half-deleted or
anything, there is no drop progress, etc.
- the subvol was created a while ago and does the meaningful first
btrfs_orphan_cleanup() call that sets BTRFS_ROOT_ORPHAN_CLEANUP much
later.
- after btrfs_orphan_cleanup() fails, btrfs_lookup_dentry() returns -ENOENT,
which results in a negative dentry for the subvolume via
d_splice_alias(NULL, dentry), leading to the observed behavior. The
bug can be mitigated by dropping the dentry cache, at which point we
can successfully delete the subvolume if we want.
i.e.,
btrfs_lookup()
btrfs_lookup_dentry()
if (!sb_rdonly(inode->vfs_inode)->vfs_inode)
btrfs_orphan_cleanup(sub_root)
test_and_set_bit(BTRFS_ROOT_ORPHAN_CLEANUP)
btrfs_search_slot() // finds orphan item for inode N
...
prints "could not do orphan cleanup -2"
if (inode == ERR_PTR(-ENOENT))
inode = NULL;
return d_splice_alias(NULL, dentry) // NEGATIVE DENTRY for valid subvolume
btrfs_orphan_cleanup() does test_and_set_bit(BTRFS_ROOT_ORPHAN_CLEANUP)
on the root when it runs, so it cannot run more than once on a given
root, so something else must run concurrently. However, the obvious
routes to deleting an orphan when nlinks goes to 0 should not be able to
run without first doing a lookup into the subvolume, which should run
btrfs_orphan_cleanup() and set the bit.
The final important observation is that create_subvol() calls
d_instantiate_new() but does not set BTRFS_ROOT_ORPHAN_CLEANUP, so if
the dentry cache gets dropped, the next lookup into the subvolume will
make a real call into btrfs_orphan_cleanup() for the first time. This
opens up the possibility of concurrently deleting the inode/orphan items
but most typical evict() paths will be holding a reference on the parent
dentry (child dentry holds parent->d_lockref.count via dget in
d_alloc(), released in __dentry_kill()) and prevent the parent from
being removed from the dentry cache.
The one exception is delayed iputs. Ordered extent creation calls
igrab() on the inode. If the file is unlinked and closed while those
refs are held, iput() in __dentry_kill() decrements i_count but does
not trigger eviction (i_count > 0). The child dentry is freed and the
subvol dentry's d_lockref.count drops to 0, making it evictable while
the inode is still alive.
Since there are two races (the race between writeback and unlink and
the race between lookup and delayed iputs), and there are too many moving
parts, the following three diagrams show the complete picture.
(Only the second and third are races)
Phase 1:
Create Subvol in dentry cache without BTRFS_ROOT_ORPHAN_CLEANUP set
btrfs_mksubvol()
lookup_one_len()
__lookup_slow()
d_alloc_parallel()
__d_alloc() // d_lockref.count = 1
create_subvol(dentry)
// doesn't touch the bit..
d_instantiate_new(dentry, inode) // dentry in cache with d_lockref.c
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-pci: ensure we're polling a polled queue
A user can change the polled queue count at run time. There's a brief
window during a reset where a hipri task may try to poll that queue
before the block layer has updated the queue maps, which would race with
the now interrupt driven queue and may cause double completions. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: prevent policy_hthresh.work from racing with netns teardown
A XFRM_MSG_NEWSPDINFO request can queue the per-net work item
policy_hthresh.work onto the system workqueue.
The queued callback, xfrm_hash_rebuild(), retrieves the enclosing
struct net via container_of(). If the net namespace is torn down
before that work runs, the associated struct net may already have
been freed, and xfrm_hash_rebuild() may then dereference stale memory.
xfrm_policy_fini() already flushes policy_hash_work during teardown,
but it does not synchronize policy_hthresh.work.
Synchronize policy_hthresh.work in xfrm_policy_fini() as well, so the
queued work cannot outlive the net namespace teardown and access a
freed struct net. |
| A race condition was addressed with additional validation. This issue is fixed in macOS Sequoia 15.3, macOS Sonoma 14.7.3, macOS Ventura 13.7.3. An app may be able to access user-sensitive data. |
