| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: ufs-qcom: Fix UFS OCP issue during UFS power down (PC=3)
According to UFS specifications, the power-off sequence for a UFS device
includes:
- Sending an SSU command with Power_Condition=3 and await a response.
- Asserting RST_N low.
- Turning off REF_CLK.
- Turning off VCC.
- Turning off VCCQ/VCCQ2.
As part of ufs shutdown, after the SSU command completion, asserting
hardware reset (HWRST) triggers the device firmware to wake up and
execute its reset routine. This routine initializes hardware blocks and
takes a few milliseconds to complete. During this time, the ICCQ draws a
large current.
This large ICCQ current may cause issues for the regulator which is
supplying power to UFS, because the turn off request from UFS driver to
the regulator framework will be immediately followed by low power
mode(LPM) request by regulator framework. This is done by framework
because UFS which is the only client is requesting for disable. So if
the rail is still in the process of shutting down while ICCQ exceeds LPM
current thresholds, and LPM mode is activated in hardware during this
state, it may trigger an overcurrent protection (OCP) fault in the
regulator.
To prevent this, a 10ms delay is added after asserting HWRST. This
allows the reset operation to complete while power rails remain active
and in high-power mode.
Currently there is no way for Host to query whether the reset is
completed or not and hence this the delay is based on experiments with
Qualcomm UFS controllers across multiple UFS vendors. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: bus: verify partner exists in typec_altmode_attention
Some usb hubs will negotiate DisplayPort Alt mode with the device
but will then negotiate a data role swap after entering the alt
mode. The data role swap causes the device to unregister all alt
modes, however the usb hub will still send Attention messages
even after failing to reregister the Alt Mode. type_altmode_attention
currently does not verify whether or not a device's altmode partner
exists, which results in a NULL pointer error when dereferencing
the typec_altmode and typec_altmode_ops belonging to the altmode
partner.
Verify the presence of a device's altmode partner before sending
the Attention message to the Alt Mode driver. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: zoned: fix memory leak after finding block group with super blocks
At exclude_super_stripes(), if we happen to find a block group that has
super blocks mapped to it and we are on a zoned filesystem, we error out
as this is not supposed to happen, indicating either a bug or maybe some
memory corruption for example. However we are exiting the function without
freeing the memory allocated for the logical address of the super blocks.
Fix this by freeing the logical address. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: spi-nor: Fix shift-out-of-bounds in spi_nor_set_erase_type
spi_nor_set_erase_type() was used either to set or to mask out an erase
type. When we used it to mask out an erase type a shift-out-of-bounds
was hit:
UBSAN: shift-out-of-bounds in drivers/mtd/spi-nor/core.c:2237:24
shift exponent 4294967295 is too large for 32-bit type 'int'
The setting of the size_{shift, mask} and of the opcode are unnecessary
when the erase size is zero, as throughout the code just the erase size
is considered to determine whether an erase type is supported or not.
Setting the opcode to 0xFF was wrong too as nobody guarantees that 0xFF
is an unused opcode. Thus when masking out an erase type, just set the
erase size to zero. This will fix the shift-out-of-bounds.
[ta: refine changes, new commit message, fix compilation error] |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Fix data race on CQP completion stats
CQP completion statistics is read lockesly in irdma_wait_event and
irdma_check_cqp_progress while it can be updated in the completion
thread irdma_sc_ccq_get_cqe_info on another CPU as KCSAN reports.
Make completion statistics an atomic variable to reflect coherent updates
to it. This will also avoid load/store tearing logic bug potentially
possible by compiler optimizations.
[77346.170861] BUG: KCSAN: data-race in irdma_handle_cqp_op [irdma] / irdma_sc_ccq_get_cqe_info [irdma]
[77346.171383] write to 0xffff8a3250b108e0 of 8 bytes by task 9544 on cpu 4:
[77346.171483] irdma_sc_ccq_get_cqe_info+0x27a/0x370 [irdma]
[77346.171658] irdma_cqp_ce_handler+0x164/0x270 [irdma]
[77346.171835] cqp_compl_worker+0x1b/0x20 [irdma]
[77346.172009] process_one_work+0x4d1/0xa40
[77346.172024] worker_thread+0x319/0x700
[77346.172037] kthread+0x180/0x1b0
[77346.172054] ret_from_fork+0x22/0x30
[77346.172136] read to 0xffff8a3250b108e0 of 8 bytes by task 9838 on cpu 2:
[77346.172234] irdma_handle_cqp_op+0xf4/0x4b0 [irdma]
[77346.172413] irdma_cqp_aeq_cmd+0x75/0xa0 [irdma]
[77346.172592] irdma_create_aeq+0x390/0x45a [irdma]
[77346.172769] irdma_rt_init_hw.cold+0x212/0x85d [irdma]
[77346.172944] irdma_probe+0x54f/0x620 [irdma]
[77346.173122] auxiliary_bus_probe+0x66/0xa0
[77346.173137] really_probe+0x140/0x540
[77346.173154] __driver_probe_device+0xc7/0x220
[77346.173173] driver_probe_device+0x5f/0x140
[77346.173190] __driver_attach+0xf0/0x2c0
[77346.173208] bus_for_each_dev+0xa8/0xf0
[77346.173225] driver_attach+0x29/0x30
[77346.173240] bus_add_driver+0x29c/0x2f0
[77346.173255] driver_register+0x10f/0x1a0
[77346.173272] __auxiliary_driver_register+0xbc/0x140
[77346.173287] irdma_init_module+0x55/0x1000 [irdma]
[77346.173460] do_one_initcall+0x7d/0x410
[77346.173475] do_init_module+0x81/0x2c0
[77346.173491] load_module+0x1232/0x12c0
[77346.173506] __do_sys_finit_module+0x101/0x180
[77346.173522] __x64_sys_finit_module+0x3c/0x50
[77346.173538] do_syscall_64+0x39/0x90
[77346.173553] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[77346.173634] value changed: 0x0000000000000094 -> 0x0000000000000095 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qedf: Fix NULL dereference in error handling
Smatch reported:
drivers/scsi/qedf/qedf_main.c:3056 qedf_alloc_global_queues()
warn: missing unwind goto?
At this point in the function, nothing has been allocated so we can return
directly. In particular the "qedf->global_queues" have not been allocated
so calling qedf_free_global_queues() will lead to a NULL dereference when
we check if (!gl[i]) and "gl" is NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
media: uvcvideo: Fix memory leak in uvc_gpio_parse
Previously the unit buffer was allocated before checking the IRQ for
privacy GPIO. In case of error, the unit buffer was leaked.
Allocate the unit buffer after the IRQ to avoid it.
Addresses-Coverity-ID: 1474639 ("Resource leak") |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: s32cc: fix uninitialized memory in s32_pinctrl_desc
s32_pinctrl_desc is allocated with devm_kmalloc(), but not all of its
fields are initialized. Notably, num_custom_params is used in
pinconf_generic_parse_dt_config(), resulting in intermittent allocation
errors, such as the following splat when probing i2c-imx:
WARNING: CPU: 0 PID: 176 at mm/page_alloc.c:4795 __alloc_pages_noprof+0x290/0x300
[...]
Hardware name: NXP S32G3 Reference Design Board 3 (S32G-VNP-RDB3) (DT)
[...]
Call trace:
__alloc_pages_noprof+0x290/0x300 (P)
___kmalloc_large_node+0x84/0x168
__kmalloc_large_node_noprof+0x34/0x120
__kmalloc_noprof+0x2ac/0x378
pinconf_generic_parse_dt_config+0x68/0x1a0
s32_dt_node_to_map+0x104/0x248
dt_to_map_one_config+0x154/0x1d8
pinctrl_dt_to_map+0x12c/0x280
create_pinctrl+0x6c/0x270
pinctrl_get+0xc0/0x170
devm_pinctrl_get+0x50/0xa0
pinctrl_bind_pins+0x60/0x2a0
really_probe+0x60/0x3a0
[...]
__platform_driver_register+0x2c/0x40
i2c_adap_imx_init+0x28/0xff8 [i2c_imx]
[...]
This results in later parse failures that can cause issues in dependent
drivers:
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c0-pins/i2c0-grp0: could not parse node property
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c0-pins/i2c0-grp0: could not parse node property
[...]
pca953x 0-0022: failed writing register: -6
i2c i2c-0: IMX I2C adapter registered
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c2-pins/i2c2-grp0: could not parse node property
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c2-pins/i2c2-grp0: could not parse node property
i2c i2c-1: IMX I2C adapter registered
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c4-pins/i2c4-grp0: could not parse node property
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c4-pins/i2c4-grp0: could not parse node property
i2c i2c-2: IMX I2C adapter registered
Fix this by initializing s32_pinctrl_desc with devm_kzalloc() instead of
devm_kmalloc() in s32_pinctrl_probe(), which sets the previously
uninitialized fields to zero. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Address KCSAN report on bpf_lru_list
KCSAN reported a data-race when accessing node->ref.
Although node->ref does not have to be accurate,
take this chance to use a more common READ_ONCE() and WRITE_ONCE()
pattern instead of data_race().
There is an existing bpf_lru_node_is_ref() and bpf_lru_node_set_ref().
This patch also adds bpf_lru_node_clear_ref() to do the
WRITE_ONCE(node->ref, 0) also.
==================================================================
BUG: KCSAN: data-race in __bpf_lru_list_rotate / __htab_lru_percpu_map_update_elem
write to 0xffff888137038deb of 1 bytes by task 11240 on cpu 1:
__bpf_lru_node_move kernel/bpf/bpf_lru_list.c:113 [inline]
__bpf_lru_list_rotate_active kernel/bpf/bpf_lru_list.c:149 [inline]
__bpf_lru_list_rotate+0x1bf/0x750 kernel/bpf/bpf_lru_list.c:240
bpf_lru_list_pop_free_to_local kernel/bpf/bpf_lru_list.c:329 [inline]
bpf_common_lru_pop_free kernel/bpf/bpf_lru_list.c:447 [inline]
bpf_lru_pop_free+0x638/0xe20 kernel/bpf/bpf_lru_list.c:499
prealloc_lru_pop kernel/bpf/hashtab.c:290 [inline]
__htab_lru_percpu_map_update_elem+0xe7/0x820 kernel/bpf/hashtab.c:1316
bpf_percpu_hash_update+0x5e/0x90 kernel/bpf/hashtab.c:2313
bpf_map_update_value+0x2a9/0x370 kernel/bpf/syscall.c:200
generic_map_update_batch+0x3ae/0x4f0 kernel/bpf/syscall.c:1687
bpf_map_do_batch+0x2d9/0x3d0 kernel/bpf/syscall.c:4534
__sys_bpf+0x338/0x810
__do_sys_bpf kernel/bpf/syscall.c:5096 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5094 [inline]
__x64_sys_bpf+0x43/0x50 kernel/bpf/syscall.c:5094
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
read to 0xffff888137038deb of 1 bytes by task 11241 on cpu 0:
bpf_lru_node_set_ref kernel/bpf/bpf_lru_list.h:70 [inline]
__htab_lru_percpu_map_update_elem+0x2f1/0x820 kernel/bpf/hashtab.c:1332
bpf_percpu_hash_update+0x5e/0x90 kernel/bpf/hashtab.c:2313
bpf_map_update_value+0x2a9/0x370 kernel/bpf/syscall.c:200
generic_map_update_batch+0x3ae/0x4f0 kernel/bpf/syscall.c:1687
bpf_map_do_batch+0x2d9/0x3d0 kernel/bpf/syscall.c:4534
__sys_bpf+0x338/0x810
__do_sys_bpf kernel/bpf/syscall.c:5096 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5094 [inline]
__x64_sys_bpf+0x43/0x50 kernel/bpf/syscall.c:5094
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x01 -> 0x00
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 11241 Comm: syz-executor.3 Not tainted 6.3.0-rc7-syzkaller-00136-g6a66fdd29ea1 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/30/2023
================================================================== |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: udlfb: Fix endpoint check
The syzbot fuzzer detected a problem in the udlfb driver, caused by an
endpoint not having the expected type:
usb 1-1: Read EDID byte 0 failed: -71
usb 1-1: Unable to get valid EDID from device/display
------------[ cut here ]------------
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 9 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880
drivers/usb/core/urb.c:504
Modules linked in:
CPU: 0 PID: 9 Comm: kworker/0:1 Not tainted
6.4.0-rc1-syzkaller-00016-ga4422ff22142 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
04/28/2023
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
...
Call Trace:
<TASK>
dlfb_submit_urb+0x92/0x180 drivers/video/fbdev/udlfb.c:1980
dlfb_set_video_mode+0x21f0/0x2950 drivers/video/fbdev/udlfb.c:315
dlfb_ops_set_par+0x2a7/0x8d0 drivers/video/fbdev/udlfb.c:1111
dlfb_usb_probe+0x149a/0x2710 drivers/video/fbdev/udlfb.c:1743
The current approach for this issue failed to catch the problem
because it only checks for the existence of a bulk-OUT endpoint; it
doesn't check whether this endpoint is the one that the driver will
actually use.
We can fix the problem by instead checking that the endpoint used by
the driver does exist and is bulk-OUT. |
| In the Linux kernel, the following vulnerability has been resolved:
media: af9005: Fix null-ptr-deref in af9005_i2c_xfer
In af9005_i2c_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach af9005_i2c_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen.
We add check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd769a
("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()") |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/srpt: Add a check for valid 'mad_agent' pointer
When unregistering MAD agent, srpt module has a non-null check
for 'mad_agent' pointer before invoking ib_unregister_mad_agent().
This check can pass if 'mad_agent' variable holds an error value.
The 'mad_agent' can have an error value for a short window when
srpt_add_one() and srpt_remove_one() is executed simultaneously.
In srpt module, added a valid pointer check for 'sport->mad_agent'
before unregistering MAD agent.
This issue can hit when RoCE driver unregisters ib_device
Stack Trace:
------------
BUG: kernel NULL pointer dereference, address: 000000000000004d
PGD 145003067 P4D 145003067 PUD 2324fe067 PMD 0
Oops: 0002 [#1] PREEMPT SMP NOPTI
CPU: 10 PID: 4459 Comm: kworker/u80:0 Kdump: loaded Tainted: P
Hardware name: Dell Inc. PowerEdge R640/06NR82, BIOS 2.5.4 01/13/2020
Workqueue: bnxt_re bnxt_re_task [bnxt_re]
RIP: 0010:_raw_spin_lock_irqsave+0x19/0x40
Call Trace:
ib_unregister_mad_agent+0x46/0x2f0 [ib_core]
IPv6: ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
? __schedule+0x20b/0x560
srpt_unregister_mad_agent+0x93/0xd0 [ib_srpt]
srpt_remove_one+0x20/0x150 [ib_srpt]
remove_client_context+0x88/0xd0 [ib_core]
bond0: (slave p2p1): link status definitely up, 100000 Mbps full duplex
disable_device+0x8a/0x160 [ib_core]
bond0: active interface up!
? kernfs_name_hash+0x12/0x80
(NULL device *): Bonding Info Received: rdev: 000000006c0b8247
__ib_unregister_device+0x42/0xb0 [ib_core]
(NULL device *): Master: mode: 4 num_slaves:2
ib_unregister_device+0x22/0x30 [ib_core]
(NULL device *): Slave: id: 105069936 name:p2p1 link:0 state:0
bnxt_re_stopqps_and_ib_uninit+0x83/0x90 [bnxt_re]
bnxt_re_alloc_lag+0x12e/0x4e0 [bnxt_re] |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: Fix a possible null-pointer dereference in ni_clear()
In a previous commit c1006bd13146, ni->mi.mrec in ni_write_inode()
could be NULL, and thus a NULL check is added for this variable.
However, in the same call stack, ni->mi.mrec can be also dereferenced
in ni_clear():
ntfs_evict_inode(inode)
ni_write_inode(inode, ...)
ni = ntfs_i(inode);
is_rec_inuse(ni->mi.mrec) -> Add a NULL check by previous commit
ni_clear(ntfs_i(inode))
is_rec_inuse(ni->mi.mrec) -> No check
Thus, a possible null-pointer dereference may exist in ni_clear().
To fix it, a NULL check is added in this function. |
| In the Linux kernel, the following vulnerability has been resolved:
security: Restrict CONFIG_ZERO_CALL_USED_REGS to gcc or clang > 15.0.6
A bad bug in clang's implementation of -fzero-call-used-regs can result
in NULL pointer dereferences (see the links above the check for more
information). Restrict CONFIG_CC_HAS_ZERO_CALL_USED_REGS to either a
supported GCC version or a clang newer than 15.0.6, which will catch
both a theoretical 15.0.7 and the upcoming 16.0.0, which will both have
the bug fixed. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/pseries: Rework lppaca_shared_proc() to avoid DEBUG_PREEMPT
lppaca_shared_proc() takes a pointer to the lppaca which is typically
accessed through get_lppaca(). With DEBUG_PREEMPT enabled, this leads
to checking if preemption is enabled, for example:
BUG: using smp_processor_id() in preemptible [00000000] code: grep/10693
caller is lparcfg_data+0x408/0x19a0
CPU: 4 PID: 10693 Comm: grep Not tainted 6.5.0-rc3 #2
Call Trace:
dump_stack_lvl+0x154/0x200 (unreliable)
check_preemption_disabled+0x214/0x220
lparcfg_data+0x408/0x19a0
...
This isn't actually a problem however, as it does not matter which
lppaca is accessed, the shared proc state will be the same.
vcpudispatch_stats_procfs_init() already works around this by disabling
preemption, but the lparcfg code does not, erroring any time
/proc/powerpc/lparcfg is accessed with DEBUG_PREEMPT enabled.
Instead of disabling preemption on the caller side, rework
lppaca_shared_proc() to not take a pointer and instead directly access
the lppaca, bypassing any potential preemption checks.
[mpe: Rework to avoid needing a definition in paca.h and lppaca.h] |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: Fix an uninit variable access bug in __ip6_make_skb()
Syzbot reported a bug as following:
=====================================================
BUG: KMSAN: uninit-value in arch_atomic64_inc arch/x86/include/asm/atomic64_64.h:88 [inline]
BUG: KMSAN: uninit-value in arch_atomic_long_inc include/linux/atomic/atomic-long.h:161 [inline]
BUG: KMSAN: uninit-value in atomic_long_inc include/linux/atomic/atomic-instrumented.h:1429 [inline]
BUG: KMSAN: uninit-value in __ip6_make_skb+0x2f37/0x30f0 net/ipv6/ip6_output.c:1956
arch_atomic64_inc arch/x86/include/asm/atomic64_64.h:88 [inline]
arch_atomic_long_inc include/linux/atomic/atomic-long.h:161 [inline]
atomic_long_inc include/linux/atomic/atomic-instrumented.h:1429 [inline]
__ip6_make_skb+0x2f37/0x30f0 net/ipv6/ip6_output.c:1956
ip6_finish_skb include/net/ipv6.h:1122 [inline]
ip6_push_pending_frames+0x10e/0x550 net/ipv6/ip6_output.c:1987
rawv6_push_pending_frames+0xb12/0xb90 net/ipv6/raw.c:579
rawv6_sendmsg+0x297e/0x2e60 net/ipv6/raw.c:922
inet_sendmsg+0x101/0x180 net/ipv4/af_inet.c:827
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg net/socket.c:734 [inline]
____sys_sendmsg+0xa8e/0xe70 net/socket.c:2476
___sys_sendmsg+0x2a1/0x3f0 net/socket.c:2530
__sys_sendmsg net/socket.c:2559 [inline]
__do_sys_sendmsg net/socket.c:2568 [inline]
__se_sys_sendmsg net/socket.c:2566 [inline]
__x64_sys_sendmsg+0x367/0x540 net/socket.c:2566
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Uninit was created at:
slab_post_alloc_hook mm/slab.h:766 [inline]
slab_alloc_node mm/slub.c:3452 [inline]
__kmem_cache_alloc_node+0x71f/0xce0 mm/slub.c:3491
__do_kmalloc_node mm/slab_common.c:967 [inline]
__kmalloc_node_track_caller+0x114/0x3b0 mm/slab_common.c:988
kmalloc_reserve net/core/skbuff.c:492 [inline]
__alloc_skb+0x3af/0x8f0 net/core/skbuff.c:565
alloc_skb include/linux/skbuff.h:1270 [inline]
__ip6_append_data+0x51c1/0x6bb0 net/ipv6/ip6_output.c:1684
ip6_append_data+0x411/0x580 net/ipv6/ip6_output.c:1854
rawv6_sendmsg+0x2882/0x2e60 net/ipv6/raw.c:915
inet_sendmsg+0x101/0x180 net/ipv4/af_inet.c:827
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg net/socket.c:734 [inline]
____sys_sendmsg+0xa8e/0xe70 net/socket.c:2476
___sys_sendmsg+0x2a1/0x3f0 net/socket.c:2530
__sys_sendmsg net/socket.c:2559 [inline]
__do_sys_sendmsg net/socket.c:2568 [inline]
__se_sys_sendmsg net/socket.c:2566 [inline]
__x64_sys_sendmsg+0x367/0x540 net/socket.c:2566
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
It is because icmp6hdr does not in skb linear region under the scenario
of SOCK_RAW socket. Access icmp6_hdr(skb)->icmp6_type directly will
trigger the uninit variable access bug.
Use a local variable icmp6_type to carry the correct value in different
scenarios. |
| In the Linux kernel, the following vulnerability has been resolved:
lib/test_kho: check if KHO is enabled
We must check whether KHO is enabled prior to issuing KHO commands,
otherwise KHO internal data structures are not initialized. |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: Fix lost destroy smbd connection when MR allocate failed
If the MR allocate failed, the smb direct connection info is NULL,
then smbd_destroy() will directly return, then the connection info
will be leaked.
Let's set the smb direct connection info to the server before call
smbd_destroy(). |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: zstd - fix double-free in per-CPU stream cleanup
The crypto/zstd module has a double-free bug that occurs when multiple
tfms are allocated and freed.
The issue happens because zstd_streams (per-CPU contexts) are freed in
zstd_exit() during every tfm destruction, rather than being managed at
the module level. When multiple tfms exist, each tfm exit attempts to
free the same shared per-CPU streams, resulting in a double-free.
This leads to a stack trace similar to:
BUG: Bad page state in process kworker/u16:1 pfn:106fd93
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x106fd93
flags: 0x17ffffc0000000(node=0|zone=2|lastcpupid=0x1fffff)
page_type: 0xffffffff()
raw: 0017ffffc0000000 dead000000000100 dead000000000122 0000000000000000
raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: nonzero entire_mapcount
Modules linked in: ...
CPU: 3 UID: 0 PID: 2506 Comm: kworker/u16:1 Kdump: loaded Tainted: G B
Hardware name: ...
Workqueue: btrfs-delalloc btrfs_work_helper
Call Trace:
<TASK>
dump_stack_lvl+0x5d/0x80
bad_page+0x71/0xd0
free_unref_page_prepare+0x24e/0x490
free_unref_page+0x60/0x170
crypto_acomp_free_streams+0x5d/0xc0
crypto_acomp_exit_tfm+0x23/0x50
crypto_destroy_tfm+0x60/0xc0
...
Change the lifecycle management of zstd_streams to free the streams only
once during module cleanup. |
| In the Linux kernel, the following vulnerability has been resolved:
mtdchar: fix integer overflow in read/write ioctls
The "req.start" and "req.len" variables are u64 values that come from the
user at the start of the function. We mask away the high 32 bits of
"req.len" so that's capped at U32_MAX but the "req.start" variable can go
up to U64_MAX which means that the addition can still integer overflow.
Use check_add_overflow() to fix this bug. |
