| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: nsh: Use correct mac_offset to unwind gso skb in nsh_gso_segment()
As the call trace shows, skb_panic was caused by wrong skb->mac_header
in nsh_gso_segment():
invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 3 PID: 2737 Comm: syz Not tainted 6.3.0-next-20230505 #1
RIP: 0010:skb_panic+0xda/0xe0
call Trace:
skb_push+0x91/0xa0
nsh_gso_segment+0x4f3/0x570
skb_mac_gso_segment+0x19e/0x270
__skb_gso_segment+0x1e8/0x3c0
validate_xmit_skb+0x452/0x890
validate_xmit_skb_list+0x99/0xd0
sch_direct_xmit+0x294/0x7c0
__dev_queue_xmit+0x16f0/0x1d70
packet_xmit+0x185/0x210
packet_snd+0xc15/0x1170
packet_sendmsg+0x7b/0xa0
sock_sendmsg+0x14f/0x160
The root cause is:
nsh_gso_segment() use skb->network_header - nhoff to reset mac_header
in skb_gso_error_unwind() if inner-layer protocol gso fails.
However, skb->network_header may be reset by inner-layer protocol
gso function e.g. mpls_gso_segment. skb->mac_header reset by the
inaccurate network_header will be larger than skb headroom.
nsh_gso_segment
nhoff = skb->network_header - skb->mac_header;
__skb_pull(skb,nsh_len)
skb_mac_gso_segment
mpls_gso_segment
skb_reset_network_header(skb);//skb->network_header+=nsh_len
return -EINVAL;
skb_gso_error_unwind
skb_push(skb, nsh_len);
skb->mac_header = skb->network_header - nhoff;
// skb->mac_header > skb->headroom, cause skb_push panic
Use correct mac_offset to restore mac_header and get rid of nhoff. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/dcssblk: fix kernel crash with list_add corruption
Commit fb08a1908cb1 ("dax: simplify the dax_device <-> gendisk
association") introduced new logic for gendisk association, requiring
drivers to explicitly call dax_add_host() and dax_remove_host().
For dcssblk driver, some dax_remove_host() calls were missing, e.g. in
device remove path. The commit also broke error handling for out_dax case
in device add path, resulting in an extra put_device() w/o the previous
get_device() in that case.
This lead to stale xarray entries after device add / remove cycles. In the
case when a previously used struct gendisk pointer (xarray index) would be
used again, because blk_alloc_disk() happened to return such a pointer, the
xa_insert() in dax_add_host() would fail and go to out_dax, doing the extra
put_device() in the error path. In combination with an already flawed error
handling in dcssblk (device_register() cleanup), which needs to be
addressed in a separate patch, this resulted in a missing device_del() /
klist_del(), and eventually in the kernel crash with list_add corruption on
a subsequent device_add() / klist_add().
Fix this by adding the missing dax_remove_host() calls, and also move the
put_device() in the error path to restore the previous logic. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: safexcel - Cleanup ring IRQ workqueues on load failure
A failure loading the safexcel driver results in the following warning
on boot, because the IRQ affinity has not been correctly cleaned up.
Ensure we clean up the affinity and workqueues on a failure to load the
driver.
crypto-safexcel: probe of f2800000.crypto failed with error -2
------------[ cut here ]------------
WARNING: CPU: 1 PID: 232 at kernel/irq/manage.c:1913 free_irq+0x300/0x340
Modules linked in: hwmon mdio_i2c crypto_safexcel(+) md5 sha256_generic libsha256 authenc libdes omap_rng rng_core nft_masq nft_nat nft_chain_nat nf_nat nft_ct nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables libcrc32c nfnetlink fuse autofs4
CPU: 1 PID: 232 Comm: systemd-udevd Tainted: G W 6.1.6-00002-g9d4898824677 #3
Hardware name: MikroTik RB5009 (DT)
pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : free_irq+0x300/0x340
lr : free_irq+0x2e0/0x340
sp : ffff800008fa3890
x29: ffff800008fa3890 x28: 0000000000000000 x27: 0000000000000000
x26: ffff8000008e6dc0 x25: ffff000009034cac x24: ffff000009034d50
x23: 0000000000000000 x22: 000000000000004a x21: ffff0000093e0d80
x20: ffff000009034c00 x19: ffff00000615fc00 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 000075f5c1584c5e
x14: 0000000000000017 x13: 0000000000000000 x12: 0000000000000040
x11: ffff000000579b60 x10: ffff000000579b62 x9 : ffff800008bbe370
x8 : ffff000000579dd0 x7 : 0000000000000000 x6 : ffff000000579e18
x5 : ffff000000579da8 x4 : ffff800008ca0000 x3 : ffff800008ca0188
x2 : 0000000013033204 x1 : ffff000009034c00 x0 : ffff8000087eadf0
Call trace:
free_irq+0x300/0x340
devm_irq_release+0x14/0x20
devres_release_all+0xa0/0x100
device_unbind_cleanup+0x14/0x60
really_probe+0x198/0x2d4
__driver_probe_device+0x74/0xdc
driver_probe_device+0x3c/0x110
__driver_attach+0x8c/0x190
bus_for_each_dev+0x6c/0xc0
driver_attach+0x20/0x30
bus_add_driver+0x148/0x1fc
driver_register+0x74/0x120
__platform_driver_register+0x24/0x30
safexcel_init+0x48/0x1000 [crypto_safexcel]
do_one_initcall+0x4c/0x1b0
do_init_module+0x44/0x1cc
load_module+0x1724/0x1be4
__do_sys_finit_module+0xbc/0x110
__arm64_sys_finit_module+0x1c/0x24
invoke_syscall+0x44/0x110
el0_svc_common.constprop.0+0xc0/0xe0
do_el0_svc+0x20/0x80
el0_svc+0x14/0x4c
el0t_64_sync_handler+0xb0/0xb4
el0t_64_sync+0x148/0x14c
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rt2x00: Fix memory leak when handling surveys
When removing a rt2x00 device, its associated channel surveys
are not freed, causing a memory leak observable with kmemleak:
unreferenced object 0xffff9620f0881a00 (size 512):
comm "systemd-udevd", pid 2290, jiffies 4294906974 (age 33.768s)
hex dump (first 32 bytes):
70 44 12 00 00 00 00 00 92 8a 00 00 00 00 00 00 pD..............
00 00 00 00 00 00 00 00 ab 87 01 00 00 00 00 00 ................
backtrace:
[<ffffffffb0ed858b>] __kmalloc+0x4b/0x130
[<ffffffffc1b0f29b>] rt2800_probe_hw+0xc2b/0x1380 [rt2800lib]
[<ffffffffc1a9496e>] rt2800usb_probe_hw+0xe/0x60 [rt2800usb]
[<ffffffffc1ae491a>] rt2x00lib_probe_dev+0x21a/0x7d0 [rt2x00lib]
[<ffffffffc1b3b83e>] rt2x00usb_probe+0x1be/0x980 [rt2x00usb]
[<ffffffffc05981e2>] usb_probe_interface+0xe2/0x310 [usbcore]
[<ffffffffb13be2d5>] really_probe+0x1a5/0x410
[<ffffffffb13be5c8>] __driver_probe_device+0x78/0x180
[<ffffffffb13be6fe>] driver_probe_device+0x1e/0x90
[<ffffffffb13be972>] __driver_attach+0xd2/0x1c0
[<ffffffffb13bbc57>] bus_for_each_dev+0x77/0xd0
[<ffffffffb13bd2a2>] bus_add_driver+0x112/0x210
[<ffffffffb13bfc6c>] driver_register+0x5c/0x120
[<ffffffffc0596ae8>] usb_register_driver+0x88/0x150 [usbcore]
[<ffffffffb0c011c4>] do_one_initcall+0x44/0x220
[<ffffffffb0d6134c>] do_init_module+0x4c/0x220
Fix this by freeing the channel surveys on device removal.
Tested with a RT3070 based USB wireless adapter. |
| In the Linux kernel, the following vulnerability has been resolved:
vfio/type1: fix cap_migration information leak
Fix an information leak where an uninitialized hole in struct
vfio_iommu_type1_info_cap_migration on the stack is exposed to userspace.
The definition of struct vfio_iommu_type1_info_cap_migration contains a hole as
shown in this pahole(1) output:
struct vfio_iommu_type1_info_cap_migration {
struct vfio_info_cap_header header; /* 0 8 */
__u32 flags; /* 8 4 */
/* XXX 4 bytes hole, try to pack */
__u64 pgsize_bitmap; /* 16 8 */
__u64 max_dirty_bitmap_size; /* 24 8 */
/* size: 32, cachelines: 1, members: 4 */
/* sum members: 28, holes: 1, sum holes: 4 */
/* last cacheline: 32 bytes */
};
The cap_mig variable is filled in without initializing the hole:
static int vfio_iommu_migration_build_caps(struct vfio_iommu *iommu,
struct vfio_info_cap *caps)
{
struct vfio_iommu_type1_info_cap_migration cap_mig;
cap_mig.header.id = VFIO_IOMMU_TYPE1_INFO_CAP_MIGRATION;
cap_mig.header.version = 1;
cap_mig.flags = 0;
/* support minimum pgsize */
cap_mig.pgsize_bitmap = (size_t)1 << __ffs(iommu->pgsize_bitmap);
cap_mig.max_dirty_bitmap_size = DIRTY_BITMAP_SIZE_MAX;
return vfio_info_add_capability(caps, &cap_mig.header, sizeof(cap_mig));
}
The structure is then copied to a temporary location on the heap. At this point
it's already too late and ioctl(VFIO_IOMMU_GET_INFO) copies it to userspace
later:
int vfio_info_add_capability(struct vfio_info_cap *caps,
struct vfio_info_cap_header *cap, size_t size)
{
struct vfio_info_cap_header *header;
header = vfio_info_cap_add(caps, size, cap->id, cap->version);
if (IS_ERR(header))
return PTR_ERR(header);
memcpy(header + 1, cap + 1, size - sizeof(*header));
return 0;
}
This issue was found by code inspection. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: fix NULL-deref on irq uninstall
In case of early initialisation errors and on platforms that do not use
the DPU controller, the deinitilisation code can be called with the kms
pointer set to NULL.
Patchwork: https://patchwork.freedesktop.org/patch/525104/ |
| In the Linux kernel, the following vulnerability has been resolved:
media: mediatek: vcodec: fix resource leaks in vdec_msg_queue_init()
If we encounter any error in the vdec_msg_queue_init() then we need
to set "msg_queue->wdma_addr.size = 0;". Normally, this is done
inside the vdec_msg_queue_deinit() function. However, if the
first call to allocate &msg_queue->wdma_addr fails, then the
vdec_msg_queue_deinit() function is a no-op. For that situation, just
set the size to zero explicitly and return.
There were two other error paths which did not clean up before returning.
Change those error paths to goto mem_alloc_err. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Fix kernel warning during topology setup
This patch fixes the following kernel warning seen during
driver load by correctly initializing the p2plink attr before
creating the sysfs file:
[ +0.002865] ------------[ cut here ]------------
[ +0.002327] kobject: '(null)' (0000000056260cfb): is not initialized, yet kobject_put() is being called.
[ +0.004780] WARNING: CPU: 32 PID: 1006 at lib/kobject.c:718 kobject_put+0xaa/0x1c0
[ +0.001361] Call Trace:
[ +0.001234] <TASK>
[ +0.001067] kfd_remove_sysfs_node_entry+0x24a/0x2d0 [amdgpu]
[ +0.003147] kfd_topology_update_sysfs+0x3d/0x750 [amdgpu]
[ +0.002890] kfd_topology_add_device+0xbd7/0xc70 [amdgpu]
[ +0.002844] ? lock_release+0x13c/0x2e0
[ +0.001936] ? smu_cmn_send_smc_msg_with_param+0x1e8/0x2d0 [amdgpu]
[ +0.003313] ? amdgpu_dpm_get_mclk+0x54/0x60 [amdgpu]
[ +0.002703] kgd2kfd_device_init.cold+0x39f/0x4ed [amdgpu]
[ +0.002930] amdgpu_amdkfd_device_init+0x13d/0x1f0 [amdgpu]
[ +0.002944] amdgpu_device_init.cold+0x1464/0x17b4 [amdgpu]
[ +0.002970] ? pci_bus_read_config_word+0x43/0x80
[ +0.002380] amdgpu_driver_load_kms+0x15/0x100 [amdgpu]
[ +0.002744] amdgpu_pci_probe+0x147/0x370 [amdgpu]
[ +0.002522] local_pci_probe+0x40/0x80
[ +0.001896] work_for_cpu_fn+0x10/0x20
[ +0.001892] process_one_work+0x26e/0x5a0
[ +0.002029] worker_thread+0x1fd/0x3e0
[ +0.001890] ? process_one_work+0x5a0/0x5a0
[ +0.002115] kthread+0xea/0x110
[ +0.001618] ? kthread_complete_and_exit+0x20/0x20
[ +0.002422] ret_from_fork+0x1f/0x30
[ +0.001808] </TASK>
[ +0.001103] irq event stamp: 59837
[ +0.001718] hardirqs last enabled at (59849): [<ffffffffb30fab12>] __up_console_sem+0x52/0x60
[ +0.004414] hardirqs last disabled at (59860): [<ffffffffb30faaf7>] __up_console_sem+0x37/0x60
[ +0.004414] softirqs last enabled at (59654): [<ffffffffb307d9c7>] irq_exit_rcu+0xd7/0x130
[ +0.004205] softirqs last disabled at (59649): [<ffffffffb307d9c7>] irq_exit_rcu+0xd7/0x130
[ +0.004203] ---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
media: platform: mtk-mdp3: Add missing check and free for ida_alloc
Add the check for the return value of the ida_alloc in order to avoid
NULL pointer dereference.
Moreover, free allocated "ctx->id" if mdp_m2m_open fails later in order
to avoid memory leak. |
| In the Linux kernel, the following vulnerability has been resolved:
can: j1939: prevent deadlock by moving j1939_sk_errqueue()
This commit addresses a deadlock situation that can occur in certain
scenarios, such as when running data TP/ETP transfer and subscribing to
the error queue while receiving a net down event. The deadlock involves
locks in the following order:
3
j1939_session_list_lock -> active_session_list_lock
j1939_session_activate
...
j1939_sk_queue_activate_next -> sk_session_queue_lock
...
j1939_xtp_rx_eoma_one
2
j1939_sk_queue_drop_all -> sk_session_queue_lock
...
j1939_sk_netdev_event_netdown -> j1939_socks_lock
j1939_netdev_notify
1
j1939_sk_errqueue -> j1939_socks_lock
__j1939_session_cancel -> active_session_list_lock
j1939_tp_rxtimer
CPU0 CPU1
---- ----
lock(&priv->active_session_list_lock);
lock(&jsk->sk_session_queue_lock);
lock(&priv->active_session_list_lock);
lock(&priv->j1939_socks_lock);
The solution implemented in this commit is to move the
j1939_sk_errqueue() call out of the active_session_list_lock context,
thus preventing the deadlock situation. |
| In the Linux kernel, the following vulnerability has been resolved:
net: core: remove unnecessary frame_sz check in bpf_xdp_adjust_tail()
Syzkaller reported the following issue:
=======================================
Too BIG xdp->frame_sz = 131072
WARNING: CPU: 0 PID: 5020 at net/core/filter.c:4121
____bpf_xdp_adjust_tail net/core/filter.c:4121 [inline]
WARNING: CPU: 0 PID: 5020 at net/core/filter.c:4121
bpf_xdp_adjust_tail+0x466/0xa10 net/core/filter.c:4103
...
Call Trace:
<TASK>
bpf_prog_4add87e5301a4105+0x1a/0x1c
__bpf_prog_run include/linux/filter.h:600 [inline]
bpf_prog_run_xdp include/linux/filter.h:775 [inline]
bpf_prog_run_generic_xdp+0x57e/0x11e0 net/core/dev.c:4721
netif_receive_generic_xdp net/core/dev.c:4807 [inline]
do_xdp_generic+0x35c/0x770 net/core/dev.c:4866
tun_get_user+0x2340/0x3ca0 drivers/net/tun.c:1919
tun_chr_write_iter+0xe8/0x210 drivers/net/tun.c:2043
call_write_iter include/linux/fs.h:1871 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x650/0xe40 fs/read_write.c:584
ksys_write+0x12f/0x250 fs/read_write.c:637
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x38/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
xdp->frame_sz > PAGE_SIZE check was introduced in commit c8741e2bfe87
("xdp: Allow bpf_xdp_adjust_tail() to grow packet size"). But Jesper
Dangaard Brouer <jbrouer@redhat.com> noted that after introducing the
xdp_init_buff() which all XDP driver use - it's safe to remove this
check. The original intend was to catch cases where XDP drivers have
not been updated to use xdp.frame_sz, but that is not longer a concern
(since xdp_init_buff).
Running the initial syzkaller repro it was discovered that the
contiguous physical memory allocation is used for both xdp paths in
tun_get_user(), e.g. tun_build_skb() and tun_alloc_skb(). It was also
stated by Jesper Dangaard Brouer <jbrouer@redhat.com> that XDP can
work on higher order pages, as long as this is contiguous physical
memory (e.g. a page). |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: wavefront: Fix integer overflow in sample size validation
The wavefront_send_sample() function has an integer overflow issue
when validating sample size. The header->size field is u32 but gets
cast to int for comparison with dev->freemem
Fix by using unsigned comparison to avoid integer overflow. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: core: Protect regulator_supply_alias_list with regulator_list_mutex
regulator_supply_alias_list was accessed without any locking in
regulator_supply_alias(), regulator_register_supply_alias(), and
regulator_unregister_supply_alias(). Concurrent registration,
unregistration and lookups can race, leading to:
1 use-after-free if an alias entry is removed while being read,
2 duplicate entries when two threads register the same alias,
3 inconsistent alias mappings observed by consumers.
Protect all traversals, insertions and deletions on
regulator_supply_alias_list with the existing regulator_list_mutex. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtl818x: rtl8187: Fix potential buffer underflow in rtl8187_rx_cb()
The rtl8187_rx_cb() calculates the rx descriptor header address
by subtracting its size from the skb tail pointer.
However, it does not validate if the received packet
(skb->len from urb->actual_length) is large enough to contain this
header.
If a truncated packet is received, this will lead to a buffer
underflow, reading memory before the start of the skb data area,
and causing a kernel panic.
Add length checks for both rtl8187 and rtl8187b descriptor headers
before attempting to access them, dropping the packet cleanly if the
check fails. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix stackmap overflow check in __bpf_get_stackid()
Syzkaller reported a KASAN slab-out-of-bounds write in __bpf_get_stackid()
when copying stack trace data. The issue occurs when the perf trace
contains more stack entries than the stack map bucket can hold,
leading to an out-of-bounds write in the bucket's data array. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix peer HE MCS assignment
In ath11k_wmi_send_peer_assoc_cmd(), peer's transmit MCS is sent to
firmware as receive MCS while peer's receive MCS sent as transmit MCS,
which goes against firmwire's definition.
While connecting to a misbehaved AP that advertises 0xffff (meaning not
supported) for 160 MHz transmit MCS map, firmware crashes due to 0xffff
is assigned to he_mcs->rx_mcs_set field.
Ext Tag: HE Capabilities
[...]
Supported HE-MCS and NSS Set
[...]
Rx and Tx MCS Maps 160 MHz
[...]
Tx HE-MCS Map 160 MHz: 0xffff
Swap the assignment to fix this issue.
As the HE rate control mask is meant to limit our own transmit MCS, it
needs to go via he_mcs->rx_mcs_set field. With the aforementioned swapping
done, change is needed as well to apply it to the peer's receive MCS.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs3: fix uninit memory after failed mi_read in mi_format_new
Fix a KMSAN un-init bug found by syzkaller.
ntfs_get_bh() expects a buffer from sb_getblk(), that buffer may not be
uptodate. We do not bring the buffer uptodate before setting it as
uptodate. If the buffer were to not be uptodate, it could mean adding a
buffer with un-init data to the mi record. Attempting to load that record
will trigger KMSAN.
Avoid this by setting the buffer as uptodate, if it’s not already, by
overwriting it. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/amdxdna: Fix an integer overflow in aie2_query_ctx_status_array()
The unpublished smatch static checker reported a warning.
drivers/accel/amdxdna/aie2_pci.c:904 aie2_query_ctx_status_array()
warn: potential user controlled sizeof overflow
'args->num_element * args->element_size' '1-u32max(user) * 1-u32max(user)'
Even this will not cause a real issue, it is better to put a reasonable
limitation for element_size and num_element. Add condition to make sure
the input element_size <= 4K and num_element <= 1K. |
| In the Linux kernel, the following vulnerability has been resolved:
PM / devfreq: hisi: Fix potential UAF in OPP handling
Ensure all required data is acquired before calling dev_pm_opp_put(opp)
to maintain correct resource acquisition and release order. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: fix null pointer deref in mt7996_conf_tx()
If a link does not have an assigned channel yet, mt7996_vif_link returns
NULL. We still need to store the updated queue settings in that case, and
apply them later.
Move the location of the queue params to within struct mt7996_vif_link. |
