| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| A vulnerability in the WebVPN service of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an authenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to improper management of authenticated sessions in the WebVPN portal. An attacker could exploit this vulnerability by authenticating with valid credentials and accessing a specific URL in the WebVPN portal. A successful exploit could allow the attacker to cause the device to reload, resulting in a temporary DoS condition. |
| A vulnerability in the SSL/TLS client of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an authenticated, remote attacker to cause a denial of service (DoS) condition on an affected device.
This vulnerability is due to improper memory management when a device initiates SSL/TLS connections. An attacker could exploit this vulnerability by ensuring that the device will connect to an SSL/TLS server that is using specific encryption parameters. A successful exploit could allow the attacker to cause the affected device to unexpectedly reload, resulting in a DoS condition. |
| A vulnerability in Cisco Secure Firewall Adaptive Security Appliance (ASA) Software and Cisco Secure Firewall Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to send traffic that should be denied through an affected device.
This vulnerability is due to improper error handling when an affected device that is joining a cluster runs out of memory while replicating access control rules. An attacker could exploit this vulnerability by sending traffic that should be blocked through the device. A successful exploit could allow the attacker to bypass access controls and reach devices in protected networks. |
| Multiple vulnerabilities in the Application Layer Protocol Inspection feature of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to trigger a reload of an affected device, resulting in a denial of service (DoS) condition. The vulnerabilities are due to logical errors during traffic inspection. An attacker could exploit these vulnerabilities by sending a high volume of malicious traffic across an affected device. An exploit could allow the attacker to cause a deadlock condition, resulting in a reload of an affected device. These vulnerabilities affect Cisco ASA Software and Cisco FTD Software configured for Application Layer Protocol Inspection running on the following Cisco products: 3000 Series Industrial Security Appliance (ISA), ASA 5500 Series Adaptive Security Appliances, ASA 5500-X Series Next-Generation Firewalls, ASA Services Module for Cisco Catalyst 6500 Series Switches and Cisco 7600 Series Routers, Adaptive Security Virtual Appliance (ASAv), Firepower 2100 Series Security Appliance, Firepower 4100 Series Security Appliance, Firepower 9300 ASA Security Module, FTD Virtual (FTDv). Cisco Bug IDs: CSCve61540, CSCvh23085, CSCvh95456. |
| A vulnerability in the geolocation access control feature of Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to bypass an access control policy.
This vulnerability is due to improper assignment of geolocation data. An attacker could exploit this vulnerability by sending traffic through an affected device. A successful exploit could allow the attacker to bypass a geolocation-based access control policy and successfully send traffic to a protected device. |
| A vulnerability in the remote access SSL VPN feature of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an authenticated, remote attacker to bypass a configured multiple certificate authentication policy and connect using only a valid username and password. This vulnerability is due to improper error handling during remote access VPN authentication. An attacker could exploit this vulnerability by sending crafted requests during remote access VPN session establishment. A successful exploit could allow the attacker to bypass the configured multiple certificate authentication policy while retaining the privileges and permissions associated with the original connection profile. |
| A vulnerability in the web services interface of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to retrieve memory contents on an affected device, which could lead to the disclosure of confidential information. The vulnerability is due to a buffer tracking issue when the software parses invalid URLs that are requested from the web services interface. An attacker could exploit this vulnerability by sending a crafted GET request to the web services interface. A successful exploit could allow the attacker to retrieve memory contents, which could lead to the disclosure of confidential information. Note: This vulnerability affects only specific AnyConnect and WebVPN configurations. For more information, see the Vulnerable Products section. |
| A vulnerability in the IP geolocation rules of Snort 3 could allow an unauthenticated, remote attacker to potentially bypass IP address restrictions. This vulnerability exists because the configuration for IP geolocation rules is not parsed properly. An attacker could exploit this vulnerability by spoofing an IP address until they bypass the restriction. A successful exploit could allow the attacker to bypass location-based IP address restrictions. |
| A "Cisco Firepower Threat Defense 6.0.0 through 6.2.2 and Cisco ASA with FirePOWER Module Denial of Service" vulnerability in the access control policy of Cisco Firepower System Software could allow an authenticated, remote attacker to cause an affected system to stop inspecting and processing packets, resulting in a denial of service (DoS) condition. The vulnerability is due to improper SSL policy handling by the affected software when packets are passed through the sensing interfaces of an affected system. An attacker could exploit this vulnerability by sending crafted packets through a targeted system. This vulnerability affects Cisco Firepower System Software that is configured with the SSL policy feature. Cisco Bug IDs: CSCvc84361. |
| A vulnerability in the SIP inspection engine of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a crash and reload of an affected device, resulting in a denial of service (DoS) condition.The vulnerability is due to a crash that occurs during a hash lookup for a SIP pinhole connection. An attacker could exploit this vulnerability by sending crafted SIP traffic through an affected device. A successful exploit could allow the attacker to cause a crash and reload of the affected device. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: i801: fix hardware state machine corruption in error path
A severe livelock and subsequent Hung Task panic were observed in the
i2c-i801 driver during concurrent Fuzzing. The crash is caused by an
unconditional hardware register cleanup in the error handling path of
i801_access().
When i801_check_pre() fails (e.g., returning -EBUSY because the SMBus
controller is actively used by BIOS/ACPI), the kernel does not actually
acquire the hardware ownership. However, the code jumps to the 'out'
label and executes:
iowrite8(SMBHSTSTS_INUSE_STS | STATUS_FLAGS, SMBHSTSTS(priv));
This forcefully clears the INUSE_STS lock and resets the hardware status
flags without owning the controller. Doing so interrupts ongoing BIOS/ACPI
transactions and totally corrupts the SMBus hardware state machine.
Consequently, all subsequent i801_access() calls fail at the pre-check
stage, triggering an endless stream of "SMBus is busy, can't use it!"
error logs. Over a slow serial console, this printk flood monopolizes
the CPU (Console Livelock), starving other processes trying to acquire
the mmap_lock down_read semaphore, ultimately triggering the hung task
watchdog.
Fix this by moving the 'out' label below the hardware register cleanup.
If i801_check_pre() fails, we safely bypass the iowrite8() and only
release the software locks (pm_runtime and mutex), strictly adhering to
the rule of not releasing resources that were never acquired. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: bla: fix report_work leak on backbone_gw purge
batadv_bla_purge_backbone_gw() removes stale backbone gateway entries,
but fails to properly handle their associated report_work:
- If report_work is running, the purge must wait for it to finish before
freeing the backbone_gw, otherwise the worker may access freed memory
(e.g. bat_priv).
- If report_work is pending, the purge must cancel it and release the
reference held for that pending work item.
The previous implementation called hlist_for_each_entry_safe() inside a
spin_lock_bh() section, but cancel_work_sync() may sleep and therefore
cannot be called from within a spinlock-protected region.
Restructure the loop to handle one entry per spinlock critical section:
acquire the lock, find the next entry to purge, remove it from the hash
list, then release the lock before calling cancel_work_sync() and
dropping the hash_entry reference. Repeat until no more entries require
purging. |
| In the Linux kernel, the following vulnerability has been resolved:
srcu: Don't queue workqueue handlers to never-online CPUs
While an srcu_struct structure is in the midst of switching from CPU-0
to all-CPUs state, it can attempt to invoke callbacks for CPUs that
have never been online. Worse yet, it can attempt in invoke callbacks
for CPUs that never will be online, even including imaginary CPUs not in
cpu_possible_mask. This can cause hangs on s390, which is not set up to
deal with workqueue handlers being scheduled on such CPUs. This commit
therefore causes Tree SRCU to refrain from queueing workqueue handlers
on CPUs that have not yet (and might never) come online.
Because callbacks are not invoked on CPUs that have not been
online, it is an error to invoke call_srcu(), synchronize_srcu(), or
synchronize_srcu_expedited() on a CPU that is not yet fully online.
However, it turns out to be less code to redirect the callbacks
from too-early invocations of call_srcu() than to warn about such
invocations. This commit therefore also redirects callbacks queued on
not-yet-fully-online CPUs to the boot CPU. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (lm90) Add lock protection to lm90_alert
Sashiko reports:
lm90_alert() executes in the smbus alert context and calls
lm90_update_confreg() to disable the hardware alert line, without
acquiring hwmon_lock.
Concurrently, sysfs write operations (such as lm90_write_convrate) hold
the hwmon_lock, temporarily modify data->config, and then restore it.
If an alert interrupt occurs concurrently with a sysfs write, the sysfs
path will overwrite the alert handler's modifications to data->config
and the hardware register.
This unintentionally re-enables the hardware alert line while the alarm is
still active, causing an interrupt storm.
Add the missing lock to lm90_alert() to solve the problem. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: bla: avoid double decrement of bla.num_requests
The bla.num_requests is increased when no request_sent was in progress. And
it is decremented in various places (announcement was received, backbone is
purged, periodic work). But the check if the request_sent is actually set
to a specific state and the atomic_dec/_inc are not safe because they are
not atomic (TOCTOU) and multiple such code portions can run concurrently.
At the same time, it is necessary to modify request_sent (state) and
bla.num_requests atomically. Otherwise batadv_bla_send_request() might set
request_sent to 1 and is interrupted. batadv_handle_announce() can then
set request_sent back to 0 and decrement num_requests before
batadv_bla_send_request() incremented it.
The two operations must therefore be locked. And since state (request_sent)
and wait_periods are only accessed inside this lock, they can be converted
to simpler datatypes. And to avoid that the bla.num_requests is touched by
a parallel running context with a valid backbone_gw reference after
batadv_bla_purge_backbone_gw() ran, a third state "stopped" is required to
correctly signal that a backbone_gw is in the state of being cleaned up. |
| In the Linux kernel, the following vulnerability has been resolved:
fwctl: pds: Validate RPC input size before parsing
The fwctl core allocates the device-specific RPC input buffer with
fwctl_rpc.in_len and passes that buffer to the driver callback.
pdsfc_fw_rpc() casts the buffer to struct fwctl_rpc_pds and then calls
pdsfc_validate_rpc(), which reads fields from that structure before
checking that the input buffer is large enough to contain it. A short
in_len can make pds_fwctl read beyond the allocation.
Reject pds RPC buffers that are smaller than struct fwctl_rpc_pds before
parsing any pds-specific fields. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tp_meter: directly shut down timer on cleanup
batadv_tp_sender_cleanup() was calling timer_delete_sync() followed by
timer_delete() to guard against the timer handler re-arming itself between
the two calls. This double-deletion hack relied on the sending status being
set to 0 to suppress re-arming.
Replace both calls with a single timer_shutdown_sync(). This function both
waits for any running timer callback to complete (like timer_delete_sync())
and permanently disarms the timer so it cannot be re-armed afterwards,
making re-arming prevention unconditional and self-documenting.
The re-arming property is also required because otherwise:
1. context 0 (batadv_tp_recv_ack()) checks in
batadv_tp_reset_sender_timer() if sending is still 1 -> it is
2. context 1 changes in batadv_tp_sender_shutdown() sending to 0 and in
this process forces the kthread to stop timer in
batadv_tp_sender_cleanup()
3. context 0 continues in batadv_tp_reset_sender_timer() and rearms the
timer -> but the reference for it is already gone |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: avoid empty VLAN responses
The commit 16116dac2339 ("batman-adv: prevent TT request storms by not
sending inconsistent TT TLVLs") added checks to the local (direct) TT
response code. But the response can also be done indirectly by another node
using the global TT state. To avoid such inconsistency states reported in
the original fix, also avoid sending empty VLANs for replies from the
global TT state. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: fix negative last_changeset_len
batadv_piv_tt::last_changeset_len len was declared as s16, but the field is
never intended to hold a negative value. When a value greater than 32767 is
assigned, it wraps to a negative signed integer.
In batadv_send_my_tt_response(), last_changeset_len is temporarily widened
to s32. The incorrectly negative s16 value propagates into the s32, causing
batadv_tt_prepare_tvlv_local_data() to allocate a full sized buffer but
populates only a small portion of it with the collected changeset. All
remaining bits are kept uninitialized.
Using an u16 avoids this type confusion and ensures that no (negative) sign
extension is performed in batadv_send_my_tt_response(). |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: fix negative tt_buff_len
batadv_orig_node::tt_buff_len was declared as s16, but the field is never
intended to hold a negative value. When a value greater than 32767 is
assigned, it wraps to a negative signed integer.
In batadv_send_other_tt_response(), tt_buff_len is temporarily widened to
s32. The incorrectly negative s16 value propagates into the s32, causing
batadv_tt_prepare_tvlv_global_data() to allocate a full sized buffer but
populates only a small portion of it with the collected changeset. All
remaining bits are kept uninitialized.
Using an u16 avoids this type confusion and ensures that no (negative) sign
extension is performed in batadv_send_other_tt_response(). |
