| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: qup: jump out of the loop in case of timeout
Original logic only sets the return value but doesn't jump out of the
loop if the bus is kept active by a client. This is not expected. A
malicious or buggy i2c client can hang the kernel in this case and
should be avoided. This is observed during a long time test with a
PCA953x GPIO extender.
Fix it by changing the logic to not only sets the return value, but also
jumps out of the loop and return to the caller with -ETIMEDOUT. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Avoid stack buffer overflow from kernel cmdline
While the kernel command line is considered trusted in most environments,
avoid writing 1 byte past the end of "acpiid" if the "str" argument is
maximum length. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to avoid out-of-boundary access in dnode page
As Jiaming Zhang reported:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x1c1/0x2a0 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0x17e/0x800 mm/kasan/report.c:480
kasan_report+0x147/0x180 mm/kasan/report.c:593
data_blkaddr fs/f2fs/f2fs.h:3053 [inline]
f2fs_data_blkaddr fs/f2fs/f2fs.h:3058 [inline]
f2fs_get_dnode_of_data+0x1a09/0x1c40 fs/f2fs/node.c:855
f2fs_reserve_block+0x53/0x310 fs/f2fs/data.c:1195
prepare_write_begin fs/f2fs/data.c:3395 [inline]
f2fs_write_begin+0xf39/0x2190 fs/f2fs/data.c:3594
generic_perform_write+0x2c7/0x910 mm/filemap.c:4112
f2fs_buffered_write_iter fs/f2fs/file.c:4988 [inline]
f2fs_file_write_iter+0x1ec8/0x2410 fs/f2fs/file.c:5216
new_sync_write fs/read_write.c:593 [inline]
vfs_write+0x546/0xa90 fs/read_write.c:686
ksys_write+0x149/0x250 fs/read_write.c:738
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xf3/0x3d0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
The root cause is in the corrupted image, there is a dnode has the same
node id w/ its inode, so during f2fs_get_dnode_of_data(), it tries to
access block address in dnode at offset 934, however it parses the dnode
as inode node, so that get_dnode_addr() returns 360, then it tries to
access page address from 360 + 934 * 4 = 4096 w/ 4 bytes.
To fix this issue, let's add sanity check for node id of all direct nodes
during f2fs_get_dnode_of_data(). |
| In the Linux kernel, the following vulnerability has been resolved:
benet: fix BUG when creating VFs
benet crashes as soon as SRIOV VFs are created:
kernel BUG at mm/vmalloc.c:3457!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 4 UID: 0 PID: 7408 Comm: test.sh Kdump: loaded Not tainted 6.16.0+ #1 PREEMPT(voluntary)
[...]
RIP: 0010:vunmap+0x5f/0x70
[...]
Call Trace:
<TASK>
__iommu_dma_free+0xe8/0x1c0
be_cmd_set_mac_list+0x3fe/0x640 [be2net]
be_cmd_set_mac+0xaf/0x110 [be2net]
be_vf_eth_addr_config+0x19f/0x330 [be2net]
be_vf_setup+0x4f7/0x990 [be2net]
be_pci_sriov_configure+0x3a1/0x470 [be2net]
sriov_numvfs_store+0x20b/0x380
kernfs_fop_write_iter+0x354/0x530
vfs_write+0x9b9/0xf60
ksys_write+0xf3/0x1d0
do_syscall_64+0x8c/0x3d0
be_cmd_set_mac_list() calls dma_free_coherent() under a spin_lock_bh.
Fix it by freeing only after the lock has been released. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/core: Exit early on perf_mmap() fail
When perf_mmap() fails to allocate a buffer, it still invokes the
event_mapped() callback of the related event. On X86 this might increase
the perf_rdpmc_allowed reference counter. But nothing undoes this as
perf_mmap_close() is never called in this case, which causes another
reference count leak.
Return early on failure to prevent that. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/core: Prevent VMA split of buffer mappings
The perf mmap code is careful about mmap()'ing the user page with the
ringbuffer and additionally the auxiliary buffer, when the event supports
it. Once the first mapping is established, subsequent mapping have to use
the same offset and the same size in both cases. The reference counting for
the ringbuffer and the auxiliary buffer depends on this being correct.
Though perf does not prevent that a related mapping is split via mmap(2),
munmap(2) or mremap(2). A split of a VMA results in perf_mmap_open() calls,
which take reference counts, but then the subsequent perf_mmap_close()
calls are not longer fulfilling the offset and size checks. This leads to
reference count leaks.
As perf already has the requirement for subsequent mappings to match the
initial mapping, the obvious consequence is that VMA splits, caused by
resizing of a mapping or partial unmapping, have to be prevented.
Implement the vm_operations_struct::may_split() callback and return
unconditionally -EINVAL.
That ensures that the mapping offsets and sizes cannot be changed after the
fact. Remapping to a different fixed address with the same size is still
possible as it takes the references for the new mapping and drops those of
the old mapping. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget : fix use-after-free in composite_dev_cleanup()
1. In func configfs_composite_bind() -> composite_os_desc_req_prepare():
if kmalloc fails, the pointer cdev->os_desc_req will be freed but not
set to NULL. Then it will return a failure to the upper-level function.
2. in func configfs_composite_bind() -> composite_dev_cleanup():
it will checks whether cdev->os_desc_req is NULL. If it is not NULL, it
will attempt to use it.This will lead to a use-after-free issue.
BUG: KASAN: use-after-free in composite_dev_cleanup+0xf4/0x2c0
Read of size 8 at addr 0000004827837a00 by task init/1
CPU: 10 PID: 1 Comm: init Tainted: G O 5.10.97-oh #1
kasan_report+0x188/0x1cc
__asan_load8+0xb4/0xbc
composite_dev_cleanup+0xf4/0x2c0
configfs_composite_bind+0x210/0x7ac
udc_bind_to_driver+0xb4/0x1ec
usb_gadget_probe_driver+0xec/0x21c
gadget_dev_desc_UDC_store+0x264/0x27c |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: Restrict conditions for adding duplicating netems to qdisc tree
netem_enqueue's duplication prevention logic breaks when a netem
resides in a qdisc tree with other netems - this can lead to a
soft lockup and OOM loop in netem_dequeue, as seen in [1].
Ensure that a duplicating netem cannot exist in a tree with other
netems.
Previous approaches suggested in discussions in chronological order:
1) Track duplication status or ttl in the sk_buff struct. Considered
too specific a use case to extend such a struct, though this would
be a resilient fix and address other previous and potential future
DOS bugs like the one described in loopy fun [2].
2) Restrict netem_enqueue recursion depth like in act_mirred with a
per cpu variable. However, netem_dequeue can call enqueue on its
child, and the depth restriction could be bypassed if the child is a
netem.
3) Use the same approach as in 2, but add metadata in netem_skb_cb
to handle the netem_dequeue case and track a packet's involvement
in duplication. This is an overly complex approach, and Jamal
notes that the skb cb can be overwritten to circumvent this
safeguard.
4) Prevent the addition of a netem to a qdisc tree if its ancestral
path contains a netem. However, filters and actions can cause a
packet to change paths when re-enqueued to the root from netem
duplication, leading us to the current solution: prevent a
duplicating netem from inhabiting the same tree as other netems.
[1] https://lore.kernel.org/netdev/8DuRWwfqjoRDLDmBMlIfbrsZg9Gx50DHJc1ilxsEBNe2D6NMoigR_eIRIG0LOjMc3r10nUUZtArXx4oZBIdUfZQrwjcQhdinnMis_0G7VEk=@willsroot.io/
[2] https://lwn.net/Articles/719297/ |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: BPF: Fix jump offset calculation in tailcall
The extra pass of bpf_int_jit_compile() skips JIT context initialization
which essentially skips offset calculation leaving out_offset = -1, so
the jmp_offset in emit_bpf_tail_call is calculated by
"#define jmp_offset (out_offset - (cur_offset))"
is a negative number, which is wrong. The final generated assembly are
as follow.
54: bgeu $a2, $t1, -8 # 0x0000004c
58: addi.d $a6, $s5, -1
5c: bltz $a6, -16 # 0x0000004c
60: alsl.d $t2, $a2, $a1, 0x3
64: ld.d $t2, $t2, 264
68: beq $t2, $zero, -28 # 0x0000004c
Before apply this patch, the follow test case will reveal soft lock issues.
cd tools/testing/selftests/bpf/
./test_progs --allow=tailcalls/tailcall_bpf2bpf_1
dmesg:
watchdog: BUG: soft lockup - CPU#2 stuck for 26s! [test_progs:25056] |
| In the Linux kernel, the following vulnerability has been resolved:
nfsd: handle get_client_locked() failure in nfsd4_setclientid_confirm()
Lei Lu recently reported that nfsd4_setclientid_confirm() did not check
the return value from get_client_locked(). a SETCLIENTID_CONFIRM could
race with a confirmed client expiring and fail to get a reference. That
could later lead to a UAF.
Fix this by getting a reference early in the case where there is an
extant confirmed client. If that fails then treat it as if there were no
confirmed client found at all.
In the case where the unconfirmed client is expiring, just fail and
return the result from get_client_locked(). |
| In the Linux kernel, the following vulnerability has been resolved:
net, hsr: reject HSR frame if skb can't hold tag
Receiving HSR frame with insufficient space to hold HSR tag in the skb
can result in a crash (kernel BUG):
[ 45.390915] skbuff: skb_under_panic: text:ffffffff86f32cac len:26 put:14 head:ffff888042418000 data:ffff888042417ff4 tail:0xe end:0x180 dev:bridge_slave_1
[ 45.392559] ------------[ cut here ]------------
[ 45.392912] kernel BUG at net/core/skbuff.c:211!
[ 45.393276] Oops: invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN NOPTI
[ 45.393809] CPU: 1 UID: 0 PID: 2496 Comm: reproducer Not tainted 6.15.0 #12 PREEMPT(undef)
[ 45.394433] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
[ 45.395273] RIP: 0010:skb_panic+0x15b/0x1d0
<snip registers, remove unreliable trace>
[ 45.402911] Call Trace:
[ 45.403105] <IRQ>
[ 45.404470] skb_push+0xcd/0xf0
[ 45.404726] br_dev_queue_push_xmit+0x7c/0x6c0
[ 45.406513] br_forward_finish+0x128/0x260
[ 45.408483] __br_forward+0x42d/0x590
[ 45.409464] maybe_deliver+0x2eb/0x420
[ 45.409763] br_flood+0x174/0x4a0
[ 45.410030] br_handle_frame_finish+0xc7c/0x1bc0
[ 45.411618] br_handle_frame+0xac3/0x1230
[ 45.413674] __netif_receive_skb_core.constprop.0+0x808/0x3df0
[ 45.422966] __netif_receive_skb_one_core+0xb4/0x1f0
[ 45.424478] __netif_receive_skb+0x22/0x170
[ 45.424806] process_backlog+0x242/0x6d0
[ 45.425116] __napi_poll+0xbb/0x630
[ 45.425394] net_rx_action+0x4d1/0xcc0
[ 45.427613] handle_softirqs+0x1a4/0x580
[ 45.427926] do_softirq+0x74/0x90
[ 45.428196] </IRQ>
This issue was found by syzkaller.
The panic happens in br_dev_queue_push_xmit() once it receives a
corrupted skb with ETH header already pushed in linear data. When it
attempts the skb_push() call, there's not enough headroom and
skb_push() panics.
The corrupted skb is put on the queue by HSR layer, which makes a
sequence of unintended transformations when it receives a specific
corrupted HSR frame (with incomplete TAG).
Fix it by dropping and consuming frames that are not long enough to
contain both ethernet and hsr headers.
Alternative fix would be to check for enough headroom before skb_push()
in br_dev_queue_push_xmit().
In the reproducer, this is injected via AF_PACKET, but I don't easily
see why it couldn't be sent over the wire from adjacent network.
Further Details:
In the reproducer, the following network interface chain is set up:
┌────────────────┐ ┌────────────────┐
│ veth0_to_hsr ├───┤ hsr_slave0 ┼───┐
└────────────────┘ └────────────────┘ │
│ ┌──────┐
├─┤ hsr0 ├───┐
│ └──────┘ │
┌────────────────┐ ┌────────────────┐ │ │┌────────┐
│ veth1_to_hsr ┼───┤ hsr_slave1 ├───┘ └┤ │
└────────────────┘ └────────────────┘ ┌┼ bridge │
││ │
│└────────┘
│
┌───────┐ │
│ ... ├──────┘
└───────┘
To trigger the events leading up to crash, reproducer sends a corrupted
HSR fr
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Destroy KFD debugfs after destroy KFD wq
Since KFD proc content was moved to kernel debugfs, we can't destroy KFD
debugfs before kfd_process_destroy_wq. Move kfd_process_destroy_wq prior
to kfd_debugfs_fini to fix a kernel NULL pointer problem. It happens
when /sys/kernel/debug/kfd was already destroyed in kfd_debugfs_fini but
kfd_process_destroy_wq calls kfd_debugfs_remove_process. This line
debugfs_remove_recursive(entry->proc_dentry);
tries to remove /sys/kernel/debug/kfd/proc/<pid> while
/sys/kernel/debug/kfd is already gone. It hangs the kernel by kernel
NULL pointer.
(cherry picked from commit 0333052d90683d88531558dcfdbf2525cc37c233) |
| In the Linux kernel, the following vulnerability has been resolved:
media: venus: protect against spurious interrupts during probe
Make sure the interrupt handler is initialized before the interrupt is
registered.
If the IRQ is registered before hfi_create(), it's possible that an
interrupt fires before the handler setup is complete, leading to a NULL
dereference.
This error condition has been observed during system boot on Rb3Gen2. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: server: split ksmbd_rdma_stop_listening() out of ksmbd_rdma_destroy()
We can't call destroy_workqueue(smb_direct_wq); before stop_sessions()!
Otherwise already existing connections try to use smb_direct_wq as
a NULL pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
NFS: Fix a race when updating an existing write
After nfs_lock_and_join_requests() tests for whether the request is
still attached to the mapping, nothing prevents a call to
nfs_inode_remove_request() from succeeding until we actually lock the
page group.
The reason is that whoever called nfs_inode_remove_request() doesn't
necessarily have a lock on the page group head.
So in order to avoid races, let's take the page group lock earlier in
nfs_lock_and_join_requests(), and hold it across the removal of the
request in nfs_inode_remove_request(). |
| In the Linux kernel, the following vulnerability has been resolved:
ACPI: pfr_update: Fix the driver update version check
The security-version-number check should be used rather
than the runtime version check for driver updates.
Otherwise, the firmware update would fail when the update binary had
a lower runtime version number than the current one.
[ rjw: Changelog edits ] |
| In the Linux kernel, the following vulnerability has been resolved:
gve: prevent ethtool ops after shutdown
A crash can occur if an ethtool operation is invoked
after shutdown() is called.
shutdown() is invoked during system shutdown to stop DMA operations
without performing expensive deallocations. It is discouraged to
unregister the netdev in this path, so the device may still be visible
to userspace and kernel helpers.
In gve, shutdown() tears down most internal data structures. If an
ethtool operation is dispatched after shutdown(), it will dereference
freed or NULL pointers, leading to a kernel panic. While graceful
shutdown normally quiesces userspace before invoking the reboot
syscall, forced shutdowns (as observed on GCP VMs) can still trigger
this path.
Fix by calling netif_device_detach() in shutdown().
This marks the device as detached so the ethtool ioctl handler
will skip dispatching operations to the driver. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Limit access to parser->buffer when trace_get_user failed
When the length of the string written to set_ftrace_filter exceeds
FTRACE_BUFF_MAX, the following KASAN alarm will be triggered:
BUG: KASAN: slab-out-of-bounds in strsep+0x18c/0x1b0
Read of size 1 at addr ffff0000d00bd5ba by task ash/165
CPU: 1 UID: 0 PID: 165 Comm: ash Not tainted 6.16.0-g6bcdbd62bd56-dirty
Hardware name: linux,dummy-virt (DT)
Call trace:
show_stack+0x34/0x50 (C)
dump_stack_lvl+0xa0/0x158
print_address_description.constprop.0+0x88/0x398
print_report+0xb0/0x280
kasan_report+0xa4/0xf0
__asan_report_load1_noabort+0x20/0x30
strsep+0x18c/0x1b0
ftrace_process_regex.isra.0+0x100/0x2d8
ftrace_regex_release+0x484/0x618
__fput+0x364/0xa58
____fput+0x28/0x40
task_work_run+0x154/0x278
do_notify_resume+0x1f0/0x220
el0_svc+0xec/0xf0
el0t_64_sync_handler+0xa0/0xe8
el0t_64_sync+0x1ac/0x1b0
The reason is that trace_get_user will fail when processing a string
longer than FTRACE_BUFF_MAX, but not set the end of parser->buffer to 0.
Then an OOB access will be triggered in ftrace_regex_release->
ftrace_process_regex->strsep->strpbrk. We can solve this problem by
limiting access to parser->buffer when trace_get_user failed. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: Fix use of uninitialized memory in do_insn_ioctl() and do_insnlist_ioctl()
syzbot reports a KMSAN kernel-infoleak in `do_insn_ioctl()`. A kernel
buffer is allocated to hold `insn->n` samples (each of which is an
`unsigned int`). For some instruction types, `insn->n` samples are
copied back to user-space, unless an error code is being returned. The
problem is that not all the instruction handlers that need to return
data to userspace fill in the whole `insn->n` samples, so that there is
an information leak. There is a similar syzbot report for
`do_insnlist_ioctl()`, although it does not have a reproducer for it at
the time of writing.
One culprit is `insn_rw_emulate_bits()` which is used as the handler for
`INSN_READ` or `INSN_WRITE` instructions for subdevices that do not have
a specific handler for that instruction, but do have an `INSN_BITS`
handler. For `INSN_READ` it only fills in at most 1 sample, so if
`insn->n` is greater than 1, the remaining `insn->n - 1` samples copied
to userspace will be uninitialized kernel data.
Another culprit is `vm80xx_ai_insn_read()` in the "vm80xx" driver. It
never returns an error, even if it fails to fill the buffer.
Fix it in `do_insn_ioctl()` and `do_insnlist_ioctl()` by making sure
that uninitialized parts of the allocated buffer are zeroed before
handling each instruction.
Thanks to Arnaud Lecomte for their fix to `do_insn_ioctl()`. That fix
replaced the call to `kmalloc_array()` with `kcalloc()`, but it is not
always necessary to clear the whole buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: pcl726: Prevent invalid irq number
The reproducer passed in an irq number(0x80008000) that was too large,
which triggered the oob.
Added an interrupt number check to prevent users from passing in an irq
number that was too large.
If `it->options[1]` is 31, then `1 << it->options[1]` is still invalid
because it shifts a 1-bit into the sign bit (which is UB in C).
Possible solutions include reducing the upper bound on the
`it->options[1]` value to 30 or lower, or using `1U << it->options[1]`.
The old code would just not attempt to request the IRQ if the
`options[1]` value were invalid. And it would still configure the
device without interrupts even if the call to `request_irq` returned an
error. So it would be better to combine this test with the test below. |
