| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
parisc: Revise __get_user() to probe user read access
Because of the way read access support is implemented, read access
interruptions are only triggered at privilege levels 2 and 3. The
kernel executes at privilege level 0, so __get_user() never triggers
a read access interruption (code 26). Thus, it is currently possible
for user code to access a read protected address via a system call.
Fix this by probing read access rights at privilege level 3 (PRIV_USER)
and setting __gu_err to -EFAULT (-14) if access isn't allowed.
Note the cmpiclr instruction does a 32-bit compare because COND macro
doesn't work inside asm. |
| In the Linux kernel, the following vulnerability has been resolved:
vsock/virtio: Validate length in packet header before skb_put()
When receiving a vsock packet in the guest, only the virtqueue buffer
size is validated prior to virtio_vsock_skb_rx_put(). Unfortunately,
virtio_vsock_skb_rx_put() uses the length from the packet header as the
length argument to skb_put(), potentially resulting in SKB overflow if
the host has gone wonky.
Validate the length as advertised by the packet header before calling
virtio_vsock_skb_rx_put(). |
| In the Linux kernel, the following vulnerability has been resolved:
iio: imu: bno055: fix OOB access of hw_xlate array
Fix a potential out-of-bounds array access of the hw_xlate array in
bno055.c.
In bno055_get_regmask(), hw_xlate was iterated over the length of the
vals array instead of the length of the hw_xlate array. In the case of
bno055_gyr_scale, the vals array is larger than the hw_xlate array,
so this could result in an out-of-bounds access. In practice, this
shouldn't happen though because a match should always be found which
breaks out of the for loop before it iterates beyond the end of the
hw_xlate array.
By adding a new hw_xlate_len field to the bno055_sysfs_attr, we can be
sure we are iterating over the correct length. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: aio_iiro_16: Fix bit shift out of bounds
When checking for a supported IRQ number, the following test is used:
if ((1 << it->options[1]) & 0xdcfc) {
However, `it->options[i]` is an unchecked `int` value from userspace, so
the shift amount could be negative or out of bounds. Fix the test by
requiring `it->options[1]` to be within bounds before proceeding with
the original test. Valid `it->options[1]` values that select the IRQ
will be in the range [1,15]. The value 0 explicitly disables the use of
interrupts. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: pcl812: Fix bit shift out of bounds
When checking for a supported IRQ number, the following test is used:
if ((1 << it->options[1]) & board->irq_bits) {
However, `it->options[i]` is an unchecked `int` value from userspace, so
the shift amount could be negative or out of bounds. Fix the test by
requiring `it->options[1]` to be within bounds before proceeding with
the original test. Valid `it->options[1]` values that select the IRQ
will be in the range [1,15]. The value 0 explicitly disables the use of
interrupts. |
| In the Linux kernel, the following vulnerability has been resolved:
phy: tegra: xusb: Fix unbalanced regulator disable in UTMI PHY mode
When transitioning from USB_ROLE_DEVICE to USB_ROLE_NONE, the code
assumed that the regulator should be disabled. However, if the regulator
is marked as always-on, regulator_is_enabled() continues to return true,
leading to an incorrect attempt to disable a regulator which is not
enabled.
This can result in warnings such as:
[ 250.155624] WARNING: CPU: 1 PID: 7326 at drivers/regulator/core.c:3004
_regulator_disable+0xe4/0x1a0
[ 250.155652] unbalanced disables for VIN_SYS_5V0
To fix this, we move the regulator control logic into
tegra186_xusb_padctl_id_override() function since it's directly related
to the ID override state. The regulator is now only disabled when the role
transitions from USB_ROLE_HOST to USB_ROLE_NONE, by checking the VBUS_ID
register. This ensures that regulator enable/disable operations are
properly balanced and only occur when actually transitioning to/from host
mode. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: fix possible infinite loop in fib6_info_uses_dev()
fib6_info_uses_dev() seems to rely on RCU without an explicit
protection.
Like the prior fix in rt6_nlmsg_size(),
we need to make sure fib6_del_route() or fib6_add_rt2node()
have not removed the anchor from the list, or we risk an infinite loop. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: prevent infinite loop in rt6_nlmsg_size()
While testing prior patch, I was able to trigger
an infinite loop in rt6_nlmsg_size() in the following place:
list_for_each_entry_rcu(sibling, &f6i->fib6_siblings,
fib6_siblings) {
rt6_nh_nlmsg_size(sibling->fib6_nh, &nexthop_len);
}
This is because fib6_del_route() and fib6_add_rt2node()
uses list_del_rcu(), which can confuse rcu readers,
because they might no longer see the head of the list.
Restart the loop if f6i->fib6_nsiblings is zero. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: nbpfaxi: Fix memory corruption in probe()
The nbpf->chan[] array is allocated earlier in the nbpf_probe() function
and it has "num_channels" elements. These three loops iterate one
element farther than they should and corrupt memory.
The changes to the second loop are more involved. In this case, we're
copying data from the irqbuf[] array into the nbpf->chan[] array. If
the data in irqbuf[i] is the error IRQ then we skip it, so the iterators
are not in sync. I added a check to ensure that we don't go beyond the
end of the irqbuf[] array. I'm pretty sure this can't happen, but it
seemed harmless to add a check.
On the other hand, after the loop has ended there is a check to ensure
that the "chan" iterator is where we expect it to be. In the original
code we went one element beyond the end of the array so the iterator
wasn't in the correct place and it would always return -EINVAL. However,
now it will always be in the correct place. I deleted the check since
we know the result. |
| In the Linux kernel, the following vulnerability has been resolved:
iwlwifi: Add missing check for alloc_ordered_workqueue
Add check for the return value of alloc_ordered_workqueue since it may
return NULL pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/tegra: nvdec: Fix dma_alloc_coherent error check
Check for NULL return value with dma_alloc_coherent, in line with
Robin's fix for vic.c in 'drm/tegra: vic: Fix DMA API misuse'. |
| In the Linux kernel, the following vulnerability has been resolved:
atm: clip: Fix memory leak of struct clip_vcc.
ioctl(ATMARP_MKIP) allocates struct clip_vcc and set it to
vcc->user_back.
The code assumes that vcc_destroy_socket() passes NULL skb
to vcc->push() when the socket is close()d, and then clip_push()
frees clip_vcc.
However, ioctl(ATMARPD_CTRL) sets NULL to vcc->push() in
atm_init_atmarp(), resulting in memory leak.
Let's serialise two ioctl() by lock_sock() and check vcc->push()
in atm_init_atmarp() to prevent memleak. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (corsair-cpro) Validate the size of the received input buffer
Add buffer_recv_size to store the size of the received bytes.
Validate buffer_recv_size in send_usb_cmd(). |
| In the Linux kernel, the following vulnerability has been resolved:
PM / devfreq: Check governor before using governor->name
Commit 96ffcdf239de ("PM / devfreq: Remove redundant governor_name from
struct devfreq") removes governor_name and uses governor->name to replace
it. But devfreq->governor may be NULL and directly using
devfreq->governor->name may cause null pointer exception. Move the check of
governor to before using governor->name. |
| In the Linux kernel, the following vulnerability has been resolved:
powercap: dtpm_cpu: Fix NULL pointer dereference in get_pd_power_uw()
The get_pd_power_uw() function can crash with a NULL pointer dereference
when em_cpu_get() returns NULL. This occurs when a CPU becomes impossible
during runtime, causing get_cpu_device() to return NULL, which propagates
through em_cpu_get() and leads to a crash when em_span_cpus() dereferences
the NULL pointer.
Add a NULL check after em_cpu_get() and return 0 if unavailable,
matching the existing fallback behavior in __dtpm_cpu_setup().
[ rjw: Drop an excess empty code line ] |
| In the Linux kernel, the following vulnerability has been resolved:
staging: fbtft: fix potential memory leak in fbtft_framebuffer_alloc()
In the error paths after fb_info structure is successfully allocated,
the memory allocated in fb_deferred_io_init() for info->pagerefs is not
freed. Fix that by adding the cleanup function on the error path. |
| In the Linux kernel, the following vulnerability has been resolved:
kasan: remove kasan_find_vm_area() to prevent possible deadlock
find_vm_area() couldn't be called in atomic_context. If find_vm_area() is
called to reports vm area information, kasan can trigger deadlock like:
CPU0 CPU1
vmalloc();
alloc_vmap_area();
spin_lock(&vn->busy.lock)
spin_lock_bh(&some_lock);
<interrupt occurs>
<in softirq>
spin_lock(&some_lock);
<access invalid address>
kasan_report();
print_report();
print_address_description();
kasan_find_vm_area();
find_vm_area();
spin_lock(&vn->busy.lock) // deadlock!
To prevent possible deadlock while kasan reports, remove kasan_find_vm_area(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: zd1211rw: Fix potential NULL pointer dereference in zd_mac_tx_to_dev()
There is a potential NULL pointer dereference in zd_mac_tx_to_dev(). For
example, the following is possible:
T0 T1
zd_mac_tx_to_dev()
/* len == skb_queue_len(q) */
while (len > ZD_MAC_MAX_ACK_WAITERS) {
filter_ack()
spin_lock_irqsave(&q->lock, flags);
/* position == skb_queue_len(q) */
for (i=1; i<position; i++)
skb = __skb_dequeue(q)
if (mac->type == NL80211_IFTYPE_AP)
skb = __skb_dequeue(q);
spin_unlock_irqrestore(&q->lock, flags);
skb_dequeue() -> NULL
Since there is a small gap between checking skb queue length and skb being
unconditionally dequeued in zd_mac_tx_to_dev(), skb_dequeue() can return NULL.
Then the pointer is passed to zd_mac_tx_status() where it is dereferenced.
In order to avoid potential NULL pointer dereference due to situations like
above, check if skb is not NULL before passing it to zd_mac_tx_status().
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/sched: Increment job count before swapping tail spsc queue
A small race exists between spsc_queue_push and the run-job worker, in
which spsc_queue_push may return not-first while the run-job worker has
already idled due to the job count being zero. If this race occurs, job
scheduling stops, leading to hangs while waiting on the job’s DMA
fences.
Seal this race by incrementing the job count before appending to the
SPSC queue.
This race was observed on a drm-tip 6.16-rc1 build with the Xe driver in
an SVM test case. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: qcom: msm: mark certain pins as invalid for interrupts
On some platforms, the UFS-reset pin has no interrupt logic in TLMM but
is nevertheless registered as a GPIO in the kernel. This enables the
user-space to trigger a BUG() in the pinctrl-msm driver by running, for
example: `gpiomon -c 0 113` on RB2.
The exact culprit is requesting pins whose intr_detection_width setting
is not 1 or 2 for interrupts. This hits a BUG() in
msm_gpio_irq_set_type(). Potentially crashing the kernel due to an
invalid request from user-space is not optimal, so let's go through the
pins and mark those that would fail the check as invalid for the irq chip
as we should not even register them as available irqs.
This function can be extended if we determine that there are more
corner-cases like this. |
