| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: cyw: fix heap overflow on a short auth frame
brcmf_notify_auth_frame_rx() takes the frame length from the firmware
event and copies the frame body with the management header offset
subtracted:
u32 mgmt_frame_len = e->datalen - sizeof(struct brcmf_rx_mgmt_data);
...
memcpy(&mgmt_frame->u, frame,
mgmt_frame_len - offsetof(struct ieee80211_mgmt, u));
The only length check is e->datalen >= sizeof(*rxframe), so mgmt_frame_len
can be anything from 0 up. offsetof(struct ieee80211_mgmt, u) is 24. When
mgmt_frame_len is below that, the subtraction wraps as an unsigned value to
a huge length. The memcpy then runs far past the kzalloc'd buffer. A
malicious or malfunctioning AP can make the frame short during the
external SAE auth exchange, so this is a remotely triggered heap overflow.
Reject frames shorter than the management header offset before the copy. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: reset full ip_vs_seq structs in ip_vs_conn_new
Commit 9a05475cebdd ("ipvs: avoid kmem_cache_zalloc in
ip_vs_conn_new") changed ip_vs_conn_new() to allocate an ip_vs_conn
object with kmem_cache_alloc(). The function then initializes many
fields explicitly, but only resets in_seq.delta and out_seq.delta in the
two struct ip_vs_seq members.
That leaves init_seq and previous_delta uninitialized. This is normally
harmless while the corresponding IP_VS_CONN_F_IN_SEQ or
IP_VS_CONN_F_OUT_SEQ flag is clear. For connections learned from a sync
message, however, ip_vs_proc_conn() preserves those flags from
IP_VS_CONN_F_BACKUP_MASK and passes opt=NULL when the message omits
IPVS_OPT_SEQ_DATA. In that case the new connection can be hashed with
SEQ flags set but with the rest of in_seq/out_seq still containing stale
slab data.
When a packet for such a connection is later handled by an IPVS
application helper, vs_fix_seq() and vs_fix_ack_seq() use
previous_delta and init_seq to rewrite TCP sequence numbers. A malformed
sync message can therefore make forwarded packets carry stale slab bytes
in their TCP seq/ack numbers, and can also corrupt the forwarded TCP
flow.
Reset both struct ip_vs_seq members completely before publishing the
connection. This matches the existing "reset struct ip_vs_seq" comment
and keeps the sequence-adjustment gates inactive unless valid sequence
data is installed later. |
| In the Linux kernel, the following vulnerability has been resolved:
net: liquidio: fix BAR resource leak on PF number failure
If cn23xx_get_pf_num() fails, the function returns without
unmapping either BAR. Unmap both BARs before returning from
the error path.
Found by manual code review. |
| In the Linux kernel, the following vulnerability has been resolved:
bnx2x: fix potential memory leak in bnx2x_alloc_mem_bp()
If the allocation of fp[i].tpa_info fails, the error path will not free
the struct bnx2x_fastpath allocated earlier, as it is not linked to the
bp structure yet. Fix that by linking it immediately after allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: use opener credentials for FSCTL mutations
SET_SPARSE, SET_ZERO_DATA and SET_COMPRESSION operate on an open SMB
handle but call VFS xattr, fallocate or fileattr helpers with the current
ksmbd worker credentials. Those helpers can revalidate inode permissions,
ownership and LSM policy independently of the SMB handle access mask.
Run each operation with the credentials captured in the target file when
the handle was opened. Keep credential handling local to these single-file
FSCTLs rather than applying session credentials to the complete IOCTL
handler, which also contains handle-less and multi-handle operations. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix memory leak in ieee80211_register_hw()
If kmemdup() fails while copying supported band structures, the error
path jumps to fail_rate. This skips rate_control_deinitialize() and
leaks the initialized local->rate_ctrl.
Fix this by adding a fail_band label that shares the rate-control cleanup
path before falling through to the remaining teardown.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still present in
v7.1-rc7.
An x86_64 allyesconfig build showed no new warnings. As we do not have a
suitable mac80211 device/driver combination to test with, no runtime
testing was able to be performed. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: use parsed transport offset in SCTP state lookup
set_sctp_state() reads the SCTP chunk header again in order to drive the
IPVS SCTP state table. For IPv6 it computes the offset with
sizeof(struct ipv6hdr), while the surrounding IPVS code uses iph.len from
ip_vs_fill_iph_skb(), where ipv6_find_hdr() has already skipped
extension headers and found the real transport header.
This makes the state machine read from the wrong offset for IPv6 SCTP
packets that carry extension headers. For example, an INIT packet with an
8-byte destination options header can be scheduled correctly by
sctp_conn_schedule(), but set_sctp_state() reads the first byte of the
SCTP verification tag as a DATA chunk type. The connection then moves
from NONE to ESTABLISHED instead of INIT1, gets the longer established
timeout, and updates the active/inactive destination counters
incorrectly. This happens even though the SCTP handshake has not
completed.
Use the parsed transport offset passed down from ip_vs_set_state() for
the SCTP chunk-header lookup. For IPv4 and IPv6 packets without
extension headers this preserves the existing offset. |
| In the Linux kernel, the following vulnerability has been resolved:
llc: fix SAP refcount leak in llc_ui_autobind()
llc_ui_autobind() opens a SAP after choosing a dynamic LSAP.
llc_sap_open() returns a reference owned by the caller, and
llc_sap_add_socket() takes a second reference for the socket's
membership in the SAP hash tables.
llc_ui_bind() drops the caller's reference after adding the socket,
but llc_ui_autobind() keeps it. When the socket is closed,
llc_sap_remove_socket() releases only the socket reference, leaving
the SAP on llc_sap_list with sk_count == 0.
This is user-visible because repeated autobind and close cycles can consume
all dynamic SAP values and make later autobinds fail with -EUSERS.
Drop the caller's reference after a successful autobind, matching
llc_ui_bind()'s ownership model. |
| In the Linux kernel, the following vulnerability has been resolved:
net: lan743x: Initialize eth_syslock spinlock before use
lan743x_hardware_init() calls pci11x1x_strap_get_status() during the
PCI11x1x probe sequence. That helper acquires the Ethernet subsystem
hardware lock via lan743x_hs_syslock_acquire(), which relies on
adapter->eth_syslock_spinlock to serialize access.
The spinlock is currently initialized only after the strap status is
read. With CONFIG_DEBUG_SPINLOCK enabled, taking the zeroed initialized
spinlock can trip the spinlock debug check.
Fix by initializing adapter->eth_syslock_spinlock before reading the
strap status so the probe path never attempts to lock an uninitialized
spinlock. |
| In the Linux kernel, the following vulnerability has been resolved:
gve: fix header buffer corruption with header-split and HW-GRO
The DQO RX datapath programs a per-buffer-queue-descriptor
header_buf_addr at post time and reads the split header back at
completion time. Both the post and the read currently index the
header buffer by queue position rather than by the buffer's identity:
- post (gve_rx_post_buffers_dqo): header_buf_addr is computed from
bufq->tail
- read (gve_rx_dqo): the header is read from desc_idx (the completion
queue head index)
This relies on the buffer-queue index and the completion-queue index
being equal for the start of every packet, i.e. on the device consuming
posted buffers and returning completions in the exact same order. That
assumption does not hold once HW-GRO is enabled with multiple
flows: coalesced segments are accepted and completed in an order that
may differ from the order buffers were posted, and segments from
different flows may interleave.
That results in two problems:
1. Wrong header slot on read. Because the read offset is derived from
the completion index (desc_idx) while the device wrote the header to
the address programmed for the buffer's buf_id, the driver can copy
a header belonging to a different packet. This shows up as
throughput drop (about 30% drop and large numbers of TCP
retransmissions) with header-split and HW-GRO both enabled and many
streams.
2. Header buffer reused while still owned by the device. The driver
advances bufq->head by one per completion and re-posts buffers based
on that. Arrival of N RX completions only guarantees that at least N
RX buffer descriptors have been read by the device. It does not
guarantee that the device has relinquished the ownership of all the
buffers corresponding to those N descriptors. With out-of-order
completions (e.g. the completion for a packet copied into buffer N
arrives before the completion for a packet copied into buffer N-1),
the driver can re-post and overwrite a header buffer that the device
is still going to write into, corrupting the header of a packet
whose completion has not yet been processed.
Fix both issues by indexing the header buffer by buf_id on both the post
and read paths. Reading from buf_id's slot is therefore always correct
regardless of completion ordering (fixes problem 1).
Indexing by buf_id also ties each header slot to the lifetime of its
buffer state. A buffer state is only returned to the free/recycle lists
when its own completion (buf_id) is processed, so its header slot can
only be re-posted after the device is done with it. This makes header
slot reuse safe under out-of-order completions (fixes problem 2).
Allocate (gve_rx_alloc_hdr_bufs) and free (gve_rx_free_hdr_bufs) the
header buffers based on num_buf_states to match the buf_id indexing. |
| In the Linux kernel, the following vulnerability has been resolved:
ieee802154: ca8210: fix cas_ctl leak on spi_async failure
ca8210_spi_transfer() allocates cas_ctl with kzalloc_obj(GFP_ATOMIC)
and relies entirely on the SPI completion callback
ca8210_spi_transfer_complete() to free it.
The spi_async() API only invokes the completion callback on successful
submission. On failure it returns a negative error code without ever
queuing the callback, which leaves cas_ctl and its embedded spi_message
and spi_transfer orphaned. Every kfree(cas_ctl) in the driver is
inside the completion callback, so there is no other reclamation path.
ca8210_spi_transfer() is called from ca8210_spi_exchange(), the
interrupt handler ca8210_interrupt_handler(), and from the retry path
inside the completion callback itself. The exchange and interrupt
handler paths loop on -EBUSY, so under sustained SPI bus contention
every retry iteration leaks a fresh cas_ctl (~600 bytes per
occurrence).
Fix it by freeing cas_ctl on the spi_async() error path. While here,
correct the misleading error string: the function calls spi_async(),
not spi_sync(). |
| In the Linux kernel, the following vulnerability has been resolved:
net: ip6_gre: require CAP_NET_ADMIN in the device netns for changelink
ip6gre_changelink() and ip6erspan_changelink() operate on at most two
netns, dev_net(dev) and the tunnel link netns t->net. They differ once
the device is created in or moved to a netns other than the one the
request runs in. The rtnl changelink path checks CAP_NET_ADMIN only
against dev_net(dev), so a caller privileged there but not in t->net can
rewrite a tunnel that lives in t->net.
Gate both ops on rtnl_dev_link_net_capable() at their top, before any
attribute is parsed. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: xen: scsiback: Free the command tag on the TMR submit-failure path
scsiback_device_action() obtains a command tag in
scsiback_get_pend_req() and submits a task-management request with
target_submit_tmr(). When target_submit_tmr() fails it returns < 0 and
scsiback jumps to the err: label, which sends a response but frees
nothing, leaking the tag.
Impact: a pvSCSI guest can leak the command tags of a LUN's session,
stopping the LUN, by issuing VSCSIIF_ACT_SCSI_ABORT or RESET requests
whenever target_submit_tmr() fails.
transport_generic_free_cmd() cannot be used here. By the time
target_submit_tmr() returns an error it has already run
__target_init_cmd() (so se_cmd->cmd_kref is one, not zero), and on its
target_get_sess_cmd() error path it has freed se_cmd->se_tmr_req via
core_tmr_release_req() while leaving SCF_SCSI_TMR_CDB set and the
pointer dangling. Letting the command release run target_free_cmd_mem()
would then double-free se_tmr_req.
Use the same helper, which returns just the tag, on this path too. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: qcom: clear opened when stream enable fails
On enable, subs->opened is set before the service_interval is validated;
an invalid interval jumps to the response label without clearing it, so
the substream is wedged at -EBUSY until a disable or disconnect.
Clear subs->opened on the enable error path. |
| In the Linux kernel, the following vulnerability has been resolved:
mailbox: mtk-adsp: fix UAF during device teardown
When the SOF audio driver fails to initialize (e.g. firmware boot
timeout), its devres unwind frees the snd_sof_dev object that the
mailbox client (mtk-adsp-ipc) reaches via chan->cl->rx_callback.
The mtk-adsp-mailbox shutdown clears the mailbox command registers
but leaves the IRQ line unmasked, so a late interrupt can still
queue a threaded handler after mbox_free_channel() had cleared
chan->cl, and mbox_chan_received_data() would then trigger UAF:
BUG: KASAN: slab-use-after-free in sof_ipc3_validate_fw_version
sof_ipc3_validate_fw_version
sof_ipc3_do_rx_work
sof_ipc3_rx_msg
mt8196_dsp_handle_request
mtk_adsp_ipc_recv
mbox_chan_received_data
mtk_adsp_mbox_isr
irq_thread_fn
Freed by task ...:
kfree
devres_release_all
really_probe
... (sof-audio-of-mt8196 probe failure)
The crash was observed roughly three seconds after the failed probe.
disable_irq() in shutdown and enable_irq() in startup. disable_irq()
also waits for any in-flight interrupts, so by the time
mbox_free_channel() proceeds to clear chan->cl no rx_callback can run.
In addition, request the IRQ with IRQF_NO_AUTOEN so it stays masked
between probe and the first client bind — otherwise an early interrupt
can crash on chan->cl == NULL in mbox_chan_received_data(). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: fix QID bit leak in pqm_create_queue()
When MES is enabled and amdgpu_amdkfd_alloc_kernel_mem() fails during
the first queue creation for a process, pqm_create_queue() returns
early via 'return retval' without going through the err_create_queue
cleanup label.
This means clear_bit(*qid, pqm->queue_slot_bitmap) is never called,
leaving the reserved QID bit permanently set in queue_slot_bitmap.
Over time this leaks QID slots, potentially exhausting all available
queue slots.
Fix this by replacing 'return retval' with 'goto err_allocate_pqn'
so that clear_bit() is always called on the error path without
touching the uninitialized pqn pointer.
AILIKFD-813
(cherry picked from commit a107f74c38edbb80d6ab64dcaeeb292c14e9779f) |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: core: Fix iSCSI ISID use-after-free in REGISTER AND MOVE
core_scsi3_emulate_pro_register_and_move() maps the PERSISTENT RESERVE OUT
parameter list with transport_kmap_data_sg() and parses the destination
TransportID with target_parse_pr_out_transport_id(). For an iSCSI
TransportID (FORMAT CODE 01b), iscsi_parse_pr_out_transport_id() returns
the ISID in iport_ptr as a raw pointer into that mapped buffer.
The function then unmaps the buffer with transport_kunmap_data_sg() before
dereferencing iport_ptr in strcmp(), __core_scsi3_locate_pr_reg() and
core_scsi3_alloc_registration(). When the parameter list spans more than
one page (PARAMETER LIST LENGTH > 4096), transport_kmap_data_sg() uses
vmap() and transport_kunmap_data_sg() does vunmap(), so the kernel virtual
address backing iport_ptr is torn down and every subsequent dereference is
a use-after-free read of the unmapped region.
Keep the parameter list mapped until iport_ptr is no longer needed: drop
the early transport_kunmap_data_sg() and unmap once on the success path,
right before returning. The error paths already unmap through the existing
"if (buf) transport_kunmap_data_sg(cmd)" at the out: label, which now runs
on every post-map error exit because buf is no longer cleared early. Only
reads of the mapping happen while spinlocks are held; the map and unmap
calls remain outside any lock. The sibling caller
core_scsi3_decode_spec_i_port() already uses the buffer before unmapping it
and is left unchanged. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: xen: scsiback: Free unsubmitted command instead of double-putting it
scsiback_get_pend_req() obtains a command tag and returns a vscsibk_pend
whose embedded se_cmd has only been memset to 0, so its cmd_kref is 0;
the se_cmd is initialised (kref_init() via target_init_cmd()) only
later, in scsiback_cmd_exec(), on the successful VSCSIIF_ACT_SCSI_CDB
path. The two error paths in scsiback_do_cmd_fn() taken before the
command is submitted -- a failed scsiback_gnttab_data_map() and an
unknown ring_req.act -- call
transport_generic_free_cmd(&pending_req->se_cmd, 0), which kref_put()s a
refcount of 0. That underflows it ("refcount_t: underflow;
use-after-free") and, as the release function is not run, leaks the
command tag.
Impact: a pvSCSI guest can leak every command tag of a LUN's session,
stopping the LUN, by submitting requests with a bad grant reference or
an unknown request type; under panic_on_warn the refcount underflow
panics the host.
Add a helper that just returns the tag with target_free_tag() and sends
the error response. It frees the tag while the v2p reference still pins
the session, and snapshots the response fields beforehand because
freeing the tag can let another ring reuse the pending_req slot. |
| In the Linux kernel, the following vulnerability has been resolved:
landlock: Fix LANDLOCK_SCOPE_SIGNAL bypass on the SIGIO path
LANDLOCK_SCOPE_SIGNAL must prevent a sandboxed process from signaling
processes outside its Landlock domain. It can be bypassed through the
asynchronous SIGIO delivery path.
A sandboxed process that owns any file or socket can arm it with
fcntl(fd, F_SETOWN, -pgid), fcntl(fd, F_SETSIG, SIGKILL) and O_ASYNC, so
that an I/O event makes the kernel deliver the chosen signal to the
whole process group. As the head of its process group's task list (the
default position right after fork()) that group can also hold the
non-sandboxed process that launched it, e.g. a supervisor or a security
monitor. The sandbox can thus kill or signal the processes
LANDLOCK_SCOPE_SIGNAL is meant to protect from it.
The scope is enforced in hook_file_send_sigiotask() against the Landlock
domain recorded at F_SETOWN time, not the live domain of the sender.
control_current_fowner() decides whether to record that domain and skips
recording it when the fowner target is in the caller's thread group,
which is safe only for a single-task target (PIDTYPE_PID, PIDTYPE_TGID).
For a process group (PIDTYPE_PGID) pid_task() returns only one member;
recording is skipped whenever that member shares the caller's thread
group, and hook_file_send_sigiotask() then lets the signal fan out to
the whole group unchecked.
Record the domain for every non single-process target so the scope is
enforced against each group member at delivery time.
That recording is necessary but not sufficient on its own: the kernel
signals a process group through its members' thread-group leaders, and
the leader of the registrant's own process can carry a different
Landlock domain than the sibling thread that armed the owner.
domain_is_scoped() would then deny that leader, even though commit
18eb75f3af40 ("landlock: Always allow signals between threads of the
same process") requires same-process delivery to be allowed.
hook_task_kill() avoids this by evaluating same_thread_group() live, per
recipient; the SIGIO path instead delegates the whole decision to a
single registration-time check, which a process-group fan-out cannot
honor.
So also record the registrant's thread group next to its domain and
exempt it at delivery: hook_file_send_sigiotask() allows the signal
whenever the recipient belongs to the registrant's own process,
restoring the same-process guarantee while keeping out-of-domain group
members blocked. The direct kill() path (hook_task_kill) already
evaluates the live domain and is unaffected.
[mic: Check pid_type earlier and improve comment, fix commit message,
fix comment formatting] |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_conncount: fix zone comparison in tuple dedup
The "already exists" dedup logic in __nf_conncount_add() decides
whether a connection has already been counted and can be skipped instead
of incrementing the connlimit count. It compares the conntrack zone of a
list entry with the zone of the connection being added using
nf_ct_zone_id() and nf_ct_zone_equal(), passing conn->zone.dir or
zone->dir as the direction argument.
Those helpers take enum ip_conntrack_dir values: IP_CT_DIR_ORIGINAL is 0
and IP_CT_DIR_REPLY is 1. However, zone->dir is a u8 bitmask:
NF_CT_ZONE_DIR_ORIG is 1, NF_CT_ZONE_DIR_REPL is 2 and
NF_CT_DEFAULT_ZONE_DIR is 3. Passing that bitmask as the enum direction
shifts the meaning of every non-zero value. An ORIG-only zone passes 1
and is tested as REPLY, while REPL-only and default zones pass 2 or 3 and
test bits beyond the valid direction range. In those cases
nf_ct_zone_id() can fall back to NF_CT_DEFAULT_ZONE_ID instead of using
the real zone id, so different zones can be treated as equal and dedup
collapses to tuple equality alone.
nf_conncount stores and compares the original-direction tuple for a
connection. If an skb already has an attached conntrack entry,
get_ct_or_tuple_from_skb() explicitly copies
ct->tuplehash[IP_CT_DIR_ORIGINAL].tuple, regardless of the packet's
ctinfo. Therefore the zone comparison in the tuple dedup path must use
IP_CT_DIR_ORIGINAL as well; the zone direction bitmask describes where a
zone id applies, not which direction this conncount tuple represents.
Fix the two dedup comparisons by passing IP_CT_DIR_ORIGINAL directly.
Do not special-case NF_CT_DEFAULT_ZONE_DIR and do not compare raw zone
ids: using the existing helpers with IP_CT_DIR_ORIGINAL preserves the
direction-aware NF_CT_DEFAULT_ZONE_ID fallback. A default bidirectional
zone contains the ORIG bit, so it naturally returns the real zone id;
reply-only zones continue to fall back for original-direction tuple
comparisons. |
