| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
x86/mm: Fix SMP ordering in switch_mm_irqs_off()
Stephen noted that it is possible to not have an smp_mb() between
the loaded_mm store and the tlb_gen load in switch_mm(), meaning the
ordering against flush_tlb_mm_range() goes out the window, and it
becomes possible for switch_mm() to not observe a recent tlb_gen
update and fail to flush the TLBs.
[ dhansen: merge conflict fixed by Ingo ] |
| In the Linux kernel, the following vulnerability has been resolved:
net/ip6_tunnel: Prevent perpetual tunnel growth
Similarly to ipv4 tunnel, ipv6 version updates dev->needed_headroom, too.
While ipv4 tunnel headroom adjustment growth was limited in
commit 5ae1e9922bbd ("net: ip_tunnel: prevent perpetual headroom growth"),
ipv6 tunnel yet increases the headroom without any ceiling.
Reflect ipv4 tunnel headroom adjustment limit on ipv6 version.
Credits to Francesco Ruggeri, who was originally debugging this issue
and wrote local Arista-specific patch and a reproducer. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/qaic: Treat remaining == 0 as error in find_and_map_user_pages()
Currently, if find_and_map_user_pages() takes a DMA xfer request from the
user with a length field set to 0, or in a rare case, the host receives
QAIC_TRANS_DMA_XFER_CONT from the device where resources->xferred_dma_size
is equal to the requested transaction size, the function will return 0
before allocating an sgt or setting the fields of the dma_xfer struct.
In that case, encode_addr_size_pairs() will try to access the sgt which
will lead to a general protection fault.
Return an EINVAL in case the user provides a zero-sized ALP, or the device
requests continuation after all of the bytes have been transferred. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-fc: move lsop put work to nvmet_fc_ls_req_op
It’s possible for more than one async command to be in flight from
__nvmet_fc_send_ls_req. For each command, a tgtport reference is taken.
In the current code, only one put work item is queued at a time, which
results in a leaked reference.
To fix this, move the work item to the nvmet_fc_ls_req_op struct, which
already tracks all resources related to the command. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject negative offsets for ALU ops
When verifying BPF programs, the check_alu_op() function validates
instructions with ALU operations. The 'offset' field in these
instructions is a signed 16-bit integer.
The existing check 'insn->off > 1' was intended to ensure the offset is
either 0, or 1 for BPF_MOD/BPF_DIV. However, because 'insn->off' is
signed, this check incorrectly accepts all negative values (e.g., -1).
This commit tightens the validation by changing the condition to
'(insn->off != 0 && insn->off != 1)'. This ensures that any value
other than the explicitly permitted 0 and 1 is rejected, hardening the
verifier against malformed BPF programs. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/guc: Check GuC running state before deregistering exec queue
In normal operation, a registered exec queue is disabled and
deregistered through the GuC, and freed only after the GuC confirms
completion. However, if the driver is forced to unbind while the exec
queue is still running, the user may call exec_destroy() after the GuC
has already been stopped and CT communication disabled.
In this case, the driver cannot receive a response from the GuC,
preventing proper cleanup of exec queue resources. Fix this by directly
releasing the resources when GuC is not running.
Here is the failure dmesg log:
"
[ 468.089581] ---[ end trace 0000000000000000 ]---
[ 468.089608] pci 0000:03:00.0: [drm] *ERROR* GT0: GUC ID manager unclean (1/65535)
[ 468.090558] pci 0000:03:00.0: [drm] GT0: total 65535
[ 468.090562] pci 0000:03:00.0: [drm] GT0: used 1
[ 468.090564] pci 0000:03:00.0: [drm] GT0: range 1..1 (1)
[ 468.092716] ------------[ cut here ]------------
[ 468.092719] WARNING: CPU: 14 PID: 4775 at drivers/gpu/drm/xe/xe_ttm_vram_mgr.c:298 ttm_vram_mgr_fini+0xf8/0x130 [xe]
"
v2: use xe_uc_fw_is_running() instead of xe_guc_ct_enabled().
As CT may go down and come back during VF migration.
(cherry picked from commit 9b42321a02c50a12b2beb6ae9469606257fbecea) |
| In the Linux kernel, the following vulnerability has been resolved:
media: nxp: imx8-isi: m2m: Fix streaming cleanup on release
If streamon/streamoff calls are imbalanced, such as when exiting an
application with Ctrl+C when streaming, the m2m usage_count will never
reach zero and the ISI channel won't be freed. Besides from that, if the
input line width is more than 2K, it will trigger a WARN_ON():
[ 59.222120] ------------[ cut here ]------------
[ 59.226758] WARNING: drivers/media/platform/nxp/imx8-isi/imx8-isi-hw.c:631 at mxc_isi_channel_chain+0xa4/0x120, CPU#4: v4l2-ctl/654
[ 59.238569] Modules linked in: ap1302
[ 59.242231] CPU: 4 UID: 0 PID: 654 Comm: v4l2-ctl Not tainted 6.16.0-rc4-next-20250704-06511-gff0e002d480a-dirty #258 PREEMPT
[ 59.253597] Hardware name: NXP i.MX95 15X15 board (DT)
[ 59.258720] pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 59.265669] pc : mxc_isi_channel_chain+0xa4/0x120
[ 59.270358] lr : mxc_isi_channel_chain+0x44/0x120
[ 59.275047] sp : ffff8000848c3b40
[ 59.278348] x29: ffff8000848c3b40 x28: ffff0000859b4c98 x27: ffff800081939f00
[ 59.285472] x26: 000000000000000a x25: ffff0000859b4cb8 x24: 0000000000000001
[ 59.292597] x23: ffff0000816f4760 x22: ffff0000816f4258 x21: ffff000084ceb780
[ 59.299720] x20: ffff000084342ff8 x19: ffff000084340000 x18: 0000000000000000
[ 59.306845] x17: 0000000000000000 x16: 0000000000000000 x15: 0000ffffdb369e1c
[ 59.313969] x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
[ 59.321093] x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000
[ 59.328217] x8 : ffff8000848c3d48 x7 : ffff800081930b30 x6 : ffff800081930b30
[ 59.335340] x5 : ffff0000859b6000 x4 : ffff80008193ae80 x3 : ffff800081022420
[ 59.342464] x2 : ffff0000852f6900 x1 : 0000000000000001 x0 : ffff000084341000
[ 59.349590] Call trace:
[ 59.352025] mxc_isi_channel_chain+0xa4/0x120 (P)
[ 59.356722] mxc_isi_m2m_streamon+0x160/0x20c
[ 59.361072] v4l_streamon+0x24/0x30
[ 59.364556] __video_do_ioctl+0x40c/0x4a0
[ 59.368560] video_usercopy+0x2bc/0x690
[ 59.372382] video_ioctl2+0x18/0x24
[ 59.375857] v4l2_ioctl+0x40/0x60
[ 59.379168] __arm64_sys_ioctl+0xac/0x104
[ 59.383172] invoke_syscall+0x48/0x104
[ 59.386916] el0_svc_common.constprop.0+0xc0/0xe0
[ 59.391613] do_el0_svc+0x1c/0x28
[ 59.394915] el0_svc+0x34/0xf4
[ 59.397966] el0t_64_sync_handler+0xa0/0xe4
[ 59.402143] el0t_64_sync+0x198/0x19c
[ 59.405801] ---[ end trace 0000000000000000 ]---
Address this issue by moving the streaming preparation and cleanup to
the vb2 .prepare_streaming() and .unprepare_streaming() operations. This
also simplifies the driver by allowing direct usage of the
v4l2_m2m_ioctl_streamon() and v4l2_m2m_ioctl_streamoff() helpers. |
| In the Linux kernel, the following vulnerability has been resolved:
sched/deadline: Stop dl_server before CPU goes offline
IBM CI tool reported kernel warning[1] when running a CPU removal
operation through drmgr[2]. i.e "drmgr -c cpu -r -q 1"
WARNING: CPU: 0 PID: 0 at kernel/sched/cpudeadline.c:219 cpudl_set+0x58/0x170
NIP [c0000000002b6ed8] cpudl_set+0x58/0x170
LR [c0000000002b7cb8] dl_server_timer+0x168/0x2a0
Call Trace:
[c000000002c2f8c0] init_stack+0x78c0/0x8000 (unreliable)
[c0000000002b7cb8] dl_server_timer+0x168/0x2a0
[c00000000034df84] __hrtimer_run_queues+0x1a4/0x390
[c00000000034f624] hrtimer_interrupt+0x124/0x300
[c00000000002a230] timer_interrupt+0x140/0x320
Git bisects to: commit 4ae8d9aa9f9d ("sched/deadline: Fix dl_server getting stuck")
This happens since:
- dl_server hrtimer gets enqueued close to cpu offline, when
kthread_park enqueues a fair task.
- CPU goes offline and drmgr removes it from cpu_present_mask.
- hrtimer fires and warning is hit.
Fix it by stopping the dl_server before CPU is marked dead.
[1]: https://lore.kernel.org/all/8218e149-7718-4432-9312-f97297c352b9@linux.ibm.com/
[2]: https://github.com/ibm-power-utilities/powerpc-utils/tree/next/src/drmgr
[sshegde: wrote the changelog and tested it] |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: amd/sdw_utils: avoid NULL deref when devm_kasprintf() fails
devm_kasprintf() may return NULL on memory allocation failure,
but the debug message prints cpus->dai_name before checking it.
Move the dev_dbg() call after the NULL check to prevent potential
NULL pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
mailbox: zynqmp-ipi: Fix SGI cleanup on unbind
The driver incorrectly determines SGI vs SPI interrupts by checking IRQ
number < 16, which fails with dynamic IRQ allocation. During unbind,
this causes improper SGI cleanup leading to kernel crash.
Add explicit irq_type field to pdata for reliable identification of SGI
interrupts (type-2) and only clean up SGI resources when appropriate. |
| In the Linux kernel, the following vulnerability has been resolved:
xsk: Harden userspace-supplied xdp_desc validation
Turned out certain clearly invalid values passed in xdp_desc from
userspace can pass xp_{,un}aligned_validate_desc() and then lead
to UBs or just invalid frames to be queued for xmit.
desc->len close to ``U32_MAX`` with a non-zero pool->tx_metadata_len
can cause positive integer overflow and wraparound, the same way low
enough desc->addr with a non-zero pool->tx_metadata_len can cause
negative integer overflow. Both scenarios can then pass the
validation successfully.
This doesn't happen with valid XSk applications, but can be used
to perform attacks.
Always promote desc->len to ``u64`` first to exclude positive
overflows of it. Use explicit check_{add,sub}_overflow() when
validating desc->addr (which is ``u64`` already).
bloat-o-meter reports a little growth of the code size:
add/remove: 0/0 grow/shrink: 2/1 up/down: 60/-16 (44)
Function old new delta
xskq_cons_peek_desc 299 330 +31
xsk_tx_peek_release_desc_batch 973 1002 +29
xsk_generic_xmit 3148 3132 -16
but hopefully this doesn't hurt the performance much. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: use RCU in ip6_output()
Use RCU in ip6_output() in order to use dst_dev_rcu() to prevent
possible UAF.
We can remove rcu_read_lock()/rcu_read_unlock() pairs
from ip6_finish_output2(). |
| In the Linux kernel, the following vulnerability has been resolved:
EDAC/i10nm: Skip DIMM enumeration on a disabled memory controller
When loading the i10nm_edac driver on some Intel Granite Rapids servers,
a call trace may appear as follows:
UBSAN: shift-out-of-bounds in drivers/edac/skx_common.c:453:16
shift exponent -66 is negative
...
__ubsan_handle_shift_out_of_bounds+0x1e3/0x390
skx_get_dimm_info.cold+0x47/0xd40 [skx_edac_common]
i10nm_get_dimm_config+0x23e/0x390 [i10nm_edac]
skx_register_mci+0x159/0x220 [skx_edac_common]
i10nm_init+0xcb0/0x1ff0 [i10nm_edac]
...
This occurs because some BIOS may disable a memory controller if there
aren't any memory DIMMs populated on this memory controller. The DIMMMTR
register of this disabled memory controller contains the invalid value
~0, resulting in the call trace above.
Fix this call trace by skipping DIMM enumeration on a disabled memory
controller. |
| In the Linux kernel, the following vulnerability has been resolved:
PM / devfreq: mtk-cci: Fix potential error pointer dereference in probe()
The drv->sram_reg pointer could be set to ERR_PTR(-EPROBE_DEFER) which
would lead to a error pointer dereference. Use IS_ERR_OR_NULL() to check
that the pointer is valid. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: debugfs: Fix legacy mode page table dump logic
In legacy mode, SSPTPTR is ignored if TT is not 00b or 01b. SSPTPTR
maybe uninitialized or zero in that case and may cause oops like:
Oops: general protection fault, probably for non-canonical address
0xf00087d3f000f000: 0000 [#1] SMP NOPTI
CPU: 2 UID: 0 PID: 786 Comm: cat Not tainted 6.16.0 #191 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.17.0-5.fc42 04/01/2014
RIP: 0010:pgtable_walk_level+0x98/0x150
RSP: 0018:ffffc90000f279c0 EFLAGS: 00010206
RAX: 0000000040000000 RBX: ffffc90000f27ab0 RCX: 000000000000001e
RDX: 0000000000000003 RSI: f00087d3f000f000 RDI: f00087d3f0010000
RBP: ffffc90000f27a00 R08: ffffc90000f27a98 R09: 0000000000000002
R10: 0000000000000000 R11: 0000000000000000 R12: f00087d3f000f000
R13: 0000000000000000 R14: 0000000040000000 R15: ffffc90000f27a98
FS: 0000764566dcb740(0000) GS:ffff8881f812c000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000764566d44000 CR3: 0000000109d81003 CR4: 0000000000772ef0
PKRU: 55555554
Call Trace:
<TASK>
pgtable_walk_level+0x88/0x150
domain_translation_struct_show.isra.0+0x2d9/0x300
dev_domain_translation_struct_show+0x20/0x40
seq_read_iter+0x12d/0x490
...
Avoid walking the page table if TT is not 00b or 01b. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: Intel: bytcr_rt5640: Fix invalid quirk input mapping
When an invalid value is passed via quirk option, currently
bytcr_rt5640 driver only shows an error message but leaves as is.
This may lead to unepxected results like OOB access.
This patch corrects the input mapping to the certain default value if
an invalid value is passed. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: Fix bootup splat with separate_gpu_drm modparam
The drm_gem_for_each_gpuvm_bo() call from lookup_vma() accesses
drm_gem_obj.gpuva.list, which is not initialized when the drm driver
does not support DRIVER_GEM_GPUVA feature. Enable it for msm_kms
drm driver to fix the splat seen when msm.separate_gpu_drm=1 modparam
is set:
[ 9.506020] Unable to handle kernel paging request at virtual address fffffffffffffff0
[ 9.523160] Mem abort info:
[ 9.523161] ESR = 0x0000000096000006
[ 9.523163] EC = 0x25: DABT (current EL), IL = 32 bits
[ 9.523165] SET = 0, FnV = 0
[ 9.523166] EA = 0, S1PTW = 0
[ 9.523167] FSC = 0x06: level 2 translation fault
[ 9.523169] Data abort info:
[ 9.523170] ISV = 0, ISS = 0x00000006, ISS2 = 0x00000000
[ 9.523171] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[ 9.523172] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[ 9.523174] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000ad370f000
[ 9.523176] [fffffffffffffff0] pgd=0000000000000000, p4d=0000000ad4787403, pud=0000000ad4788403, pmd=0000000000000000
[ 9.523184] Internal error: Oops: 0000000096000006 [#1] SMP
[ 9.592968] CPU: 9 UID: 0 PID: 448 Comm: (udev-worker) Not tainted 6.17.0-rc4-assorted-fix-00005-g0e9bb53a2282-dirty #3 PREEMPT
[ 9.592970] Hardware name: Qualcomm CRD, BIOS 6.0.240718.BOOT.MXF.2.4-00515-HAMOA-1 07/18/2024
[ 9.592971] pstate: a1400005 (NzCv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--)
[ 9.592973] pc : lookup_vma+0x28/0xe0 [msm]
[ 9.592996] lr : get_vma_locked+0x2c/0x128 [msm]
[ 9.763632] sp : ffff800082dab460
[ 9.763666] Call trace:
[ 9.763668] lookup_vma+0x28/0xe0 [msm] (P)
[ 9.763688] get_vma_locked+0x2c/0x128 [msm]
[ 9.763706] msm_gem_get_and_pin_iova_range+0x68/0x11c [msm]
[ 9.763723] msm_gem_get_and_pin_iova+0x18/0x24 [msm]
[ 9.763740] msm_fbdev_driver_fbdev_probe+0xd0/0x258 [msm]
[ 9.763760] __drm_fb_helper_initial_config_and_unlock+0x288/0x528 [drm_kms_helper]
[ 9.763771] drm_fb_helper_initial_config+0x44/0x54 [drm_kms_helper]
[ 9.763779] drm_fbdev_client_hotplug+0x84/0xd4 [drm_client_lib]
[ 9.763782] drm_client_register+0x58/0x9c [drm]
[ 9.763806] drm_fbdev_client_setup+0xe8/0xcf0 [drm_client_lib]
[ 9.763809] drm_client_setup+0xb4/0xd8 [drm_client_lib]
[ 9.763811] msm_drm_kms_post_init+0x2c/0x3c [msm]
[ 9.763830] msm_drm_init+0x1a8/0x22c [msm]
[ 9.763848] msm_drm_bind+0x30/0x3c [msm]
[ 9.919273] try_to_bring_up_aggregate_device+0x168/0x1d4
[ 9.919283] __component_add+0xa4/0x170
[ 9.919286] component_add+0x14/0x20
[ 9.919288] msm_dp_display_probe_tail+0x4c/0xac [msm]
[ 9.919315] msm_dp_auxbus_done_probe+0x14/0x20 [msm]
[ 9.919335] dp_aux_ep_probe+0x4c/0xf0 [drm_dp_aux_bus]
[ 9.919341] really_probe+0xbc/0x298
[ 9.919345] __driver_probe_device+0x78/0x12c
[ 9.919348] driver_probe_device+0x40/0x160
[ 9.919350] __driver_attach+0x94/0x19c
[ 9.919353] bus_for_each_dev+0x74/0xd4
[ 9.919355] driver_attach+0x24/0x30
[ 9.919358] bus_add_driver+0xe4/0x208
[ 9.919360] driver_register+0x60/0x128
[ 9.919363] __dp_aux_dp_driver_register+0x24/0x30 [drm_dp_aux_bus]
[ 9.919365] atana33xc20_init+0x20/0x1000 [panel_samsung_atna33xc20]
[ 9.919370] do_one_initcall+0x6c/0x1b0
[ 9.919374] do_init_module+0x58/0x234
[ 9.919377] load_module+0x19cc/0x1bd4
[ 9.919380] init_module_from_file+0x84/0xc4
[ 9.919382] __arm64_sys_finit_module+0x1b8/0x2cc
[ 9.919384] invoke_syscall+0x48/0x110
[ 9.919389] el0_svc_common.constprop.0+0xc8/0xe8
[ 9.919393] do_el0_svc+0x20/0x2c
[ 9.919396] el0_svc+0x34/0xf0
[ 9.919401] el0t_64_sync_handler+0xa0/0xe4
[ 9.919403] el0t_64_sync+0x198/0x19c
[ 9.919407] Code: eb0000bf 54000480 d100a003 aa0303e2 (f8418c44)
[ 9.919410] ---[ end trace 0000000000000000 ]---
Patchwork: https://patchwork.freedesktop.org/pa
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: BPF: No support of struct argument in trampoline programs
The current implementation does not support struct argument. This causes
a oops when running bpf selftest:
$ ./test_progs -a tracing_struct
Oops[#1]:
CPU -1 Unable to handle kernel paging request at virtual address 0000000000000018, era == 9000000085bef268, ra == 90000000844f3938
rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
rcu: 1-...0: (19 ticks this GP) idle=1094/1/0x4000000000000000 softirq=1380/1382 fqs=801
rcu: (detected by 0, t=5252 jiffies, g=1197, q=52 ncpus=4)
Sending NMI from CPU 0 to CPUs 1:
rcu: rcu_preempt kthread starved for 2495 jiffies! g1197 f0x0 RCU_GP_DOING_FQS(6) ->state=0x0 ->cpu=2
rcu: Unless rcu_preempt kthread gets sufficient CPU time, OOM is now expected behavior.
rcu: RCU grace-period kthread stack dump:
task:rcu_preempt state:I stack:0 pid:15 tgid:15 ppid:2 task_flags:0x208040 flags:0x00000800
Stack : 9000000100423e80 0000000000000402 0000000000000010 90000001003b0680
9000000085d88000 0000000000000000 0000000000000040 9000000087159350
9000000085c2b9b0 0000000000000001 900000008704a000 0000000000000005
00000000ffff355b 00000000ffff355b 0000000000000000 0000000000000004
9000000085d90510 0000000000000000 0000000000000002 7b5d998f8281e86e
00000000ffff355c 7b5d998f8281e86e 000000000000003f 9000000087159350
900000008715bf98 0000000000000005 9000000087036000 900000008704a000
9000000100407c98 90000001003aff80 900000008715c4c0 9000000085c2b9b0
00000000ffff355b 9000000085c33d3c 00000000000000b4 0000000000000000
9000000007002150 00000000ffff355b 9000000084615480 0000000007000002
...
Call Trace:
[<9000000085c2a868>] __schedule+0x410/0x1520
[<9000000085c2b9ac>] schedule+0x34/0x190
[<9000000085c33d38>] schedule_timeout+0x98/0x140
[<90000000845e9120>] rcu_gp_fqs_loop+0x5f8/0x868
[<90000000845ed538>] rcu_gp_kthread+0x260/0x2e0
[<900000008454e8a4>] kthread+0x144/0x238
[<9000000085c26b60>] ret_from_kernel_thread+0x28/0xc8
[<90000000844f20e4>] ret_from_kernel_thread_asm+0xc/0x88
rcu: Stack dump where RCU GP kthread last ran:
Sending NMI from CPU 0 to CPUs 2:
NMI backtrace for cpu 2 skipped: idling at idle_exit+0x0/0x4
Reject it for now. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Add NULL pointer checks in dc_stream cursor attribute functions
The function dc_stream_set_cursor_attributes() currently dereferences
the `stream` pointer and nested members `stream->ctx->dc->current_state`
without checking for NULL.
All callers of these functions, such as in
`dcn30_apply_idle_power_optimizations()` and
`amdgpu_dm_plane_handle_cursor_update()`, already perform NULL checks
before calling these functions.
Fixes below:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_stream.c:336 dc_stream_program_cursor_attributes()
error: we previously assumed 'stream' could be null (see line 334)
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_stream.c
327 bool dc_stream_program_cursor_attributes(
328 struct dc_stream_state *stream,
329 const struct dc_cursor_attributes *attributes)
330 {
331 struct dc *dc;
332 bool reset_idle_optimizations = false;
333
334 dc = stream ? stream->ctx->dc : NULL;
^^^^^^
The old code assumed stream could be NULL.
335
--> 336 if (dc_stream_set_cursor_attributes(stream, attributes)) {
^^^^^^
The refactor added an unchecked dereference.
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_stream.c
313 bool dc_stream_set_cursor_attributes(
314 struct dc_stream_state *stream,
315 const struct dc_cursor_attributes *attributes)
316 {
317 bool result = false;
318
319 if (dc_stream_check_cursor_attributes(stream, stream->ctx->dc->current_state, attributes)) {
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ Here.
This function used to check for if stream as NULL and return false at
the start. Probably we should add that back. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-throttle: fix access race during throttle policy activation
On repeated cold boots we occasionally hit a NULL pointer crash in
blk_should_throtl() when throttling is consulted before the throttle
policy is fully enabled for the queue. Checking only q->td != NULL is
insufficient during early initialization, so blkg_to_pd() for the
throttle policy can still return NULL and blkg_to_tg() becomes NULL,
which later gets dereferenced.
Unable to handle kernel NULL pointer dereference
at virtual address 0000000000000156
...
pc : submit_bio_noacct+0x14c/0x4c8
lr : submit_bio_noacct+0x48/0x4c8
sp : ffff800087f0b690
x29: ffff800087f0b690 x28: 0000000000005f90 x27: ffff00068af393c0
x26: 0000000000080000 x25: 000000000002fbc0 x24: ffff000684ddcc70
x23: 0000000000000000 x22: 0000000000000000 x21: 0000000000000000
x20: 0000000000080000 x19: ffff000684ddcd08 x18: ffffffffffffffff
x17: 0000000000000000 x16: ffff80008132a550 x15: 0000ffff98020fff
x14: 0000000000000000 x13: 1fffe000d11d7021 x12: ffff000688eb810c
x11: ffff00077ec4bb80 x10: ffff000688dcb720 x9 : ffff80008068ef60
x8 : 00000a6fb8a86e85 x7 : 000000000000111e x6 : 0000000000000002
x5 : 0000000000000246 x4 : 0000000000015cff x3 : 0000000000394500
x2 : ffff000682e35e40 x1 : 0000000000364940 x0 : 000000000000001a
Call trace:
submit_bio_noacct+0x14c/0x4c8
verity_map+0x178/0x2c8
__map_bio+0x228/0x250
dm_submit_bio+0x1c4/0x678
__submit_bio+0x170/0x230
submit_bio_noacct_nocheck+0x16c/0x388
submit_bio_noacct+0x16c/0x4c8
submit_bio+0xb4/0x210
f2fs_submit_read_bio+0x4c/0xf0
f2fs_mpage_readpages+0x3b0/0x5f0
f2fs_readahead+0x90/0xe8
Tighten blk_throtl_activated() to also require that the throttle policy
bit is set on the queue:
return q->td != NULL &&
test_bit(blkcg_policy_throtl.plid, q->blkcg_pols);
This prevents blk_should_throtl() from accessing throttle group state
until policy data has been attached to blkgs. |
