| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
memory: tegra124-emc: Fix dll_change check
The code checking whether the specified memory timing enables DLL
in the EMRS register was reversed. DLL is enabled if bit A0 is low.
Fix the check. |
| In the Linux kernel, the following vulnerability has been resolved:
soc/tegra: cbb: Fix incorrect ARRAY_SIZE in fabric lookup tables
Fix incorrect ARRAY_SIZE usage in fabric lookup tables which could
cause out-of-bounds access during target timeout lookup. |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2/dlm: validate qr_numregions in dlm_match_regions()
Patch series "ocfs2/dlm: fix two bugs in dlm_match_regions()".
In dlm_match_regions(), the qr_numregions field from a DLM_QUERY_REGION
network message is used to drive loops over the qr_regions buffer without
sufficient validation. This series fixes two issues:
- Patch 1 adds a bounds check to reject messages where qr_numregions
exceeds O2NM_MAX_REGIONS. The o2net layer only validates message
byte length; it does not constrain field values, so a crafted message
can set qr_numregions up to 255 and trigger out-of-bounds reads past
the 1024-byte qr_regions buffer.
- Patch 2 fixes an off-by-one in the local-vs-remote comparison loop,
which uses '<=' instead of '<', reading one entry past the valid range
even when qr_numregions is within bounds.
This patch (of 2):
The qr_numregions field from a DLM_QUERY_REGION network message is used
directly as loop bounds in dlm_match_regions() without checking against
O2NM_MAX_REGIONS. Since qr_regions is sized for at most O2NM_MAX_REGIONS
(32) entries, a crafted message with qr_numregions > 32 causes
out-of-bounds reads past the qr_regions buffer.
Add a bounds check for qr_numregions before entering the loops. |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: fix listxattr handling when the buffer is full
[BUG]
If an OCFS2 inode has both inline and block-based xattrs, listxattr()
can return a size larger than the caller's buffer when the inline names
consume that buffer exactly.
kernel BUG at mm/usercopy.c:102!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
RIP: 0010:usercopy_abort+0xb7/0xd0 mm/usercopy.c:102
Call Trace:
__check_heap_object+0xe3/0x120 mm/slub.c:8243
check_heap_object mm/usercopy.c:196 [inline]
__check_object_size mm/usercopy.c:250 [inline]
__check_object_size+0x5c5/0x780 mm/usercopy.c:215
check_object_size include/linux/ucopysize.h:22 [inline]
check_copy_size include/linux/ucopysize.h:59 [inline]
copy_to_user include/linux/uaccess.h:219 [inline]
listxattr+0xb0/0x170 fs/xattr.c:926
filename_listxattr fs/xattr.c:958 [inline]
path_listxattrat+0x137/0x320 fs/xattr.c:988
__do_sys_listxattr fs/xattr.c:1001 [inline]
__se_sys_listxattr fs/xattr.c:998 [inline]
__x64_sys_listxattr+0x7f/0xd0 fs/xattr.c:998
...
[CAUSE]
Commit 936b8834366e ("ocfs2: Refactor xattr list and remove
ocfs2_xattr_handler().") replaced the old per-handler list accounting
with ocfs2_xattr_list_entry(), but it kept using size == 0 to detect
probe mode.
That assumption stops being true once ocfs2_listxattr() finishes the
inline-xattr pass. If the inline names fill the caller buffer exactly,
the block-xattr pass runs with a non-NULL buffer and a remaining size of
zero. ocfs2_xattr_list_entry() then skips the bounds check, keeps
counting block names, and returns a positive size larger than the
supplied buffer.
[FIX]
Detect probe mode by testing whether the destination buffer pointer is
NULL instead of whether the remaining size is zero.
That restores the pre-refactor behavior and matches the OCFS2 getxattr
helpers. Once the remaining buffer reaches zero while more names are
left, the block-xattr pass now returns -ERANGE instead of reporting a
size larger than the allocated list buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: validate bg_bits during freefrag scan
[BUG]
A crafted filesystem can trigger an out-of-bounds bitmap walk when
OCFS2_IOC_INFO is issued with OCFS2_INFO_FL_NON_COHERENT.
BUG: KASAN: use-after-free in instrument_atomic_read include/linux/instrumented.h:68 [inline]
BUG: KASAN: use-after-free in _test_bit include/asm-generic/bitops/instrumented-non-atomic.h:141 [inline]
BUG: KASAN: use-after-free in test_bit_le include/asm-generic/bitops/le.h:21 [inline]
BUG: KASAN: use-after-free in ocfs2_info_freefrag_scan_chain fs/ocfs2/ioctl.c:495 [inline]
BUG: KASAN: use-after-free in ocfs2_info_freefrag_scan_bitmap fs/ocfs2/ioctl.c:588 [inline]
BUG: KASAN: use-after-free in ocfs2_info_handle_freefrag fs/ocfs2/ioctl.c:662 [inline]
BUG: KASAN: use-after-free in ocfs2_info_handle_request+0x1c66/0x3370 fs/ocfs2/ioctl.c:754
Read of size 8 at addr ffff888031bce000 by task syz.0.636/1435
Call Trace:
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0xbe/0x130 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xd1/0x650 mm/kasan/report.c:482
kasan_report+0xfb/0x140 mm/kasan/report.c:595
check_region_inline mm/kasan/generic.c:186 [inline]
kasan_check_range+0x11c/0x200 mm/kasan/generic.c:200
__kasan_check_read+0x11/0x20 mm/kasan/shadow.c:31
instrument_atomic_read include/linux/instrumented.h:68 [inline]
_test_bit include/asm-generic/bitops/instrumented-non-atomic.h:141 [inline]
test_bit_le include/asm-generic/bitops/le.h:21 [inline]
ocfs2_info_freefrag_scan_chain fs/ocfs2/ioctl.c:495 [inline]
ocfs2_info_freefrag_scan_bitmap fs/ocfs2/ioctl.c:588 [inline]
ocfs2_info_handle_freefrag fs/ocfs2/ioctl.c:662 [inline]
ocfs2_info_handle_request+0x1c66/0x3370 fs/ocfs2/ioctl.c:754
ocfs2_info_handle+0x18d/0x2a0 fs/ocfs2/ioctl.c:828
ocfs2_ioctl+0x632/0x6e0 fs/ocfs2/ioctl.c:913
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:597 [inline]
__se_sys_ioctl fs/ioctl.c:583 [inline]
__x64_sys_ioctl+0x197/0x1e0 fs/ioctl.c:583
...
[CAUSE]
ocfs2_info_freefrag_scan_chain() uses on-disk bg_bits directly as the
bitmap scan limit. The coherent path reads group descriptors through
ocfs2_read_group_descriptor(), which validates the descriptor before
use. The non-coherent path uses ocfs2_read_blocks_sync() instead and
skips that validation, so an impossible bg_bits value can drive the
bitmap walk past the end of the block.
[FIX]
Compute the bitmap capacity from the filesystem format with
ocfs2_group_bitmap_size(), report descriptors whose bg_bits exceeds
that limit, and clamp the scan to the computed capacity. This keeps the
freefrag report going while avoiding reads beyond the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, arm64: Fix off-by-one in check_imm signed range check
check_imm(bits, imm) is used in the arm64 BPF JIT to verify that
a branch displacement (in arm64 instruction units) fits into the
signed N-bit immediate field of a B, B.cond or CBZ/CBNZ encoding
before it is handed to the encoder. The macro currently tests for
(imm > 0 && imm >> bits) || (imm < 0 && ~imm >> bits) which admits
values in [-2^N, 2^N) — effectively a signed (N+1)-bit range. A
signed N-bit field only holds [-2^(N-1), 2^(N-1)), so the check
admits one extra bit of range on each side.
In particular, for check_imm19(), values in [2^18, 2^19) slip past
the check but do not fit into the 19-bit signed imm19 field of
B.cond. aarch64_insn_encode_immediate() then masks the raw value
into the 19-bit field, setting bit 18 (the sign bit) and flipping
a forward branch into a backward one. Same class of issue exists
for check_imm26() and the B/BL encoding. Shift by (bits - 1)
instead of bits so the actual signed N-bit range is enforced. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: fix nfs4_file access extra count in nfsd4_add_rdaccess_to_wrdeleg
In nfsd4_add_rdaccess_to_wrdeleg, if fp->fi_fds[O_RDONLY] is already
set by another thread, __nfs4_file_get_access should not be called
to increment the nfs4_file access count since that was already done
by the thread that added READ access to the file. The extra fi_access
count in nfs4_file can prevent the corresponding nfsd_file from being
freed.
When stopping nfs-server service, these extra access counts trigger a
BUG in kmem_cache_destroy() that shows nfsd_file object remaining on
__kmem_cache_shutdown.
This problem can be reproduced by running the Git project's test
suite over NFS. |
| In the Linux kernel, the following vulnerability has been resolved:
um: Fix potential race condition in TLB sync
During the TLB sync, we need to traverse and modify the page table,
so we should hold the page table lock. Since full SMP support for
threads within the same process is still missing, let's disable the
split page table lock for simplicity. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: avoid double drm_exec_fini() in userq validate
When new_addition is true, amdgpu_userq_vm_validate() calls
drm_exec_fini(&exec) before iterating over the collected HMM ranges and
calling amdgpu_ttm_tt_get_user_pages().
If amdgpu_ttm_tt_get_user_pages() fails in that path, the code jumps to
unlock_all and calls drm_exec_fini(&exec) a second time on the same
exec object. drm_exec_fini() is not idempotent: it frees exec->objects
and may also drop exec->contended and finalize the ww acquire context.
Route that error path directly to the range cleanup once exec has
already been finalized.
Issue found using a prototype static analysis tool
and confirmed by code review.
(cherry picked from commit 2802952e4a07306da6ebe813ff1acacc5691851a) |
| In the Linux kernel, the following vulnerability has been resolved:
virt: sev-guest: Do not use host-controlled page order in cleanup path
When issuing an extended guest request (SVM_VMGEXIT_EXT_GUEST_REQUEST),
get_ext_report() allocates a buffer to retrieve a certificate blob from the
host, keeping track of its size in report_req->certs_len.
However, the host may return SNP_GUEST_VMM_ERR_INVALID_LEN, indicating
an invalid buffer size, as well as the expected length of such buffer.
get_ext_report() subsequently updates report_req->certs_len with the
host-controlled value, and cleans up the buffer by computing a page order
from such value. This is incorrect, as the host-provided length may not
match the page order of the original allocation, potentially resulting
in corruption in the page allocator.
Fix this by using alloc_pages_exact() instead, and reusing @npages to
compute the size passed to free_pages_exact(). For consistency, also
use @npages to compute the size when allocating the pages, even though
this last change has no functional effect. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu: Fix WARN_ON in __iommu_group_set_domain_nofail() due to reset
In __iommu_group_set_domain_internal(), concurrent domain attachments are
rejected when any device in the group is recovering. This is necessary to
fence concurrent attachments to a multi-device group where devices might
share the same RID due to PCI DMA alias quirks, but triggers the WARN_ON in
__iommu_group_set_domain_nofail().
Other IOMMU_SET_DOMAIN_MUST_SUCCEED callers in detach/teardown paths, such
as __iommu_group_set_core_domain and __iommu_release_dma_ownership, should
not be rejected, as the domain would be freed anyway in these nofail paths
while group->domain is still pointing to it. So pci_dev_reset_iommu_done()
could trigger a UAF when re-attaching group->domain.
Honor the IOMMU_SET_DOMAIN_MUST_SUCCEED flag, allowing the callers through
the group->recovery_cnt fence, so as to update the group->domain pointer.
Instead add a gdev->blocked check in the device iteration loop, to prevent
any concurrent per-device detachment. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tvlv: reject oversized TVLV packets
batadv_tvlv_container_ogm_append() builds a TVLV packet section from
the tvlv.container_list. The total size of this section is computed by
batadv_tvlv_container_list_size(), which sums the sizes of all registered
containers.
The return type and accumulator in batadv_tvlv_container_list_size() were
u16. If the accumulated size exceeds U16_MAX, the value wraps around,
causing the subsequent allocation in batadv_tvlv_container_ogm_append()
to be undersized. The memcpy-style copy that follows would then write
beyond the end of the allocated buffer, corrupting kernel memory.
Fix this by widening the return type of batadv_tvlv_container_list_size()
to size_t. In batadv_tvlv_container_ogm_append(), check the computed length
against U16_MAX before proceeding, and bail out as if the allocation had
failed when the limit is exceeded. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: ipcomp: Free destination pages on acomp errors
Move the out_free_req label up by a couple of lines so that the
allocated dst SG list gets freed on error as well as success. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: dat: handle forward allocation error
batadv_dat_forward_data() calls pskb_copy_for_clone() to duplicate an skb
for each DHT candidate, but does not check the return value before passing
it to batadv_send_skb_prepare_unicast_4addr(). That function dereferences
the skb unconditionally, so a failed allocation triggers a NULL pointer
dereference.
Skip forwarding to the current DHT candidate on allocation failure. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: fix tp_meter counter underflow during shutdown
batadv_tp_sender_shutdown() unconditionally decrements the "sending"
atomic counter. If multiple paths (e.g. timeout, user cancel, and
normal finish) call this function, the counter can underflow to -1.
Since the sender logic treats any non-zero value as "still sending",
a negative value causes the sender kthread to loop indefinitely.
This leads to a use-after-free when the interface is removed while
the zombie thread is still active.
Fix this by using atomic_xchg() to ensure the counter only transitions
from 1 to 0 once.
[sven: added missing change in batadv_tp_send] |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: scope conn->binding slowpath to bound sessions only
When the binding SESSION_SETUP sets conn->binding = true, the flag stays
set after the call so that the global session lookup in
ksmbd_session_lookup_all() can find the session, which was not added to
conn->sessions. Because the flag is connection-wide, the global lookup
path will also resolve any other session by id if asked.
Tighten the global lookup so that the returned session must have this
connection registered in its channel xarray (sess->ksmbd_chann_list).
The channel entry is installed by the existing binding_session path in
ntlm_authenticate()/krb5_authenticate() when a SESSION_SETUP completes
successfully, so this condition is a strict equivalent of "this
connection has been accepted as a channel of this session". Connections
that have not bound to a given session cannot reach it via the global
table.
The existing conn->binding gate for entering the slowpath is preserved
so that non-binding connections keep the fast-path-only behavior, and
the session->state check is unchanged. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix NULL pointer dereference in bpf_sk_storage_clone and diag paths
bpf_selem_unlink_nofail() sets SDATA(selem)->smap to NULL before
removing the selem from the storage hlist. A concurrent RCU reader in
bpf_sk_storage_clone() can observe the selem still on the list with
smap already NULL, causing a NULL pointer dereference.
general protection fault, probably for non-canonical address 0xdffffc000000000a:
KASAN: null-ptr-deref in range [0x0000000000000050-0x0000000000000057]
RIP: 0010:bpf_sk_storage_clone+0x1cd/0xaa0 net/core/bpf_sk_storage.c:174
Call Trace:
<IRQ>
sk_clone+0xfed/0x1980 net/core/sock.c:2591
inet_csk_clone_lock+0x30/0x760 net/ipv4/inet_connection_sock.c:1222
tcp_create_openreq_child+0x35/0x2680 net/ipv4/tcp_minisocks.c:571
tcp_v4_syn_recv_sock+0x123/0xf90 net/ipv4/tcp_ipv4.c:1729
tcp_check_req+0x8e1/0x2580 include/net/tcp.h:855
tcp_v4_rcv+0x1845/0x3b80 net/ipv4/tcp_ipv4.c:2347
Add a NULL check for smap in bpf_sk_storage_clone().
bpf_sk_storage_diag_put_all() has the same issue. Add a NULL check
and pass the validated smap directly to diag_get(), which is refactored
to take smap as a parameter instead of reading it internally.
bpf_sk_storage_diag_put() uses diag->maps[i] which is always valid
under its refcount, so diag->maps[i] is passed directly to diag_get(). |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: hda/conexant: Fix missing error check for jack detection
In cx_probe(), the return value of snd_hda_jack_detect_enable_callback()
is ignored. This function returns a pointer, and if it fails (e.g., due
to memory allocation failure), it returns an error pointer which must
be checked using IS_ERR().
If the registration fails, the driver continues to probe, but the jack
detection callback will not be registered. This can lead to a kernel
crash later when the driver attempts to handle jack events or accesses
the uninitialized structure.
Check the return value using IS_ERR() and propagate the error via
PTR_ERR() to the probe caller. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: eip93 - fix hmac setkey algo selection
eip93_hmac_setkey() allocates a temporary ahash transform for
computing HMAC ipad/opad key material. The allocation uses the
driver-specific cra_driver_name (e.g. "sha256-eip93") but passes
CRYPTO_ALG_ASYNC as the mask, which excludes async algorithms.
Since the EIP93 hash algorithms are the only ones registered
under those driver names and they are inherently async, the
lookup is self-contradictory and always fails with -ENOENT.
When called from the AEAD setkey path, this failure leaves the
SA record partially initialized with zeroed digest fields. A
subsequent crypto operation then dereferences a NULL pointer in
the request context, resulting in a kernel panic:
```
pc : eip93_aead_handle_result+0xc8c/0x1240 [crypto_hw_eip93]
lr : eip93_aead_handle_result+0xbec/0x1240 [crypto_hw_eip93]
sp : ffffffc082feb820
x29: ffffffc082feb820 x28: ffffff8011043980 x27: 0000000000000000
x26: 0000000000000000 x25: ffffffc078da0bc8 x24: 0000000091043980
x23: ffffff8004d59e50 x22: ffffff8004d59410 x21: ffffff8004d593c0
x20: ffffff8004d593c0 x19: ffffff8004d4f300 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 0000007fda7aa498
x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000000 x10: fffffffff8127a80 x9 : 0000000000000000
x8 : ffffff8004d4f380 x7 : 0000000000000000 x6 : 000000000000003f
x5 : 0000000000000040 x4 : 0000000000000008 x3 : 0000000000000009
x2 : 0000000000000008 x1 : 0000000028000003 x0 : ffffff8004d388c0
Code: 910142b6 f94012e0 f9002aa0 f90006d3 (f9400740)
```
The reported symbol eip93_aead_handle_result+0xc8c is a
resolution artifact from static functions being merged under
the nearest exported symbol. Decoding the faulting sequence:
```
910142b6 ADD X22, X21, #0x50
f94012e0 LDR X0, [X23, #0x20]
f9002aa0 STR X0, [X21, #0x50]
f90006d3 STR X19, [X22, #0x8]
f9400740 LDR X0, [X26, #0x8]
```
The faulting LDR at [X26, #0x8] is loading ctx->flags
(offset 8 in eip93_hash_ctx), where ctx has been resolved
to NULL from a partially initialized or unreachable
transform context following the failed setkey.
Fix this by dropping the CRYPTO_ALG_ASYNC mask from the
crypto_alloc_ahash() call. The code already handles async
completion correctly via crypto_wait_req(), so there is no
requirement to restrict the lookup to synchronous algorithms.
Note that hashing a single 64-byte block through the hardware
is likely slower than doing it in software due to the DMA
round-trip overhead, but offloading it may still spare CPU
cycles on the slower embedded cores where this IP is found.
[Detailed investigation report of this bug] |
| In the Linux kernel, the following vulnerability has been resolved:
dm cache: fix write hang in passthrough mode
The invalidate_remove() function has incomplete logic for handling write
hit bios after cache invalidation. It sets up the remapping for the
overwrite_bio but then drops it immediately without submission, causing
write operations to hang.
Fix by adding a new invalidate_committed() continuation that submits
the remapped writes to the cache origin after metadata commit completes,
while using the overwrite_endio hook to ensure proper completion
sequencing. This maintains existing coherency. Also improve error
handling in invalidate_complete() to preserve the original error status
instead of using bio_io_error() unconditionally. |
