| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm/dsi: don't dump registers past the mapped region
On DSI 6G platforms the IO address space is internally adjusted by
io_offset. Later this adjusted address might be used for memory dumping.
However the size that is used for memory dumping isn't adjusted to
account for the io_offset, leading to the potential access to the
unmapped region. Lower ctrl_size by the io_offset value to prevent
access past the mapped area.
msm_disp_snapshot_add_block+0x1d4/0x3c8 [msm] (P)
msm_dsi_host_snapshot+0x4c/0x78 [msm]
msm_dsi_snapshot+0x28/0x50 [msm]
msm_disp_snapshot_capture_state+0x74/0x140 [msm]
msm_disp_snapshot_state_sync+0x60/0x90 [msm]
_msm_disp_snapshot_work+0x30/0x90 [msm]
kthread_worker_fn+0xdc/0x460
kthread+0x120/0x140
Patchwork: https://patchwork.freedesktop.org/patch/721747/ |
| In the Linux kernel, the following vulnerability has been resolved:
Input: elan_i2c - validate firmware size before use
Ensure that the firmware file is large enough to contain the expected
number of pages and the signature (which resides at the end of the
firmware blob) before accessing them to prevent potential out-of-bounds
reads. |
| FFmpeg versions 0.7.1 through 8.1.2 contain an out-of-bounds read vulnerability in the S/PDIF muxer that allows attackers to access memory beyond buffer boundaries by supplying a crafted DTS stream with a core_size value larger than the actual packet length. Attackers can exploit the missing bounds check in the spdif_header_dts4 function by providing a malicious DTS-HD audio stream during S/PDIF re-muxing to trigger unauthorized memory reads beyond the packet buffer. |
| When expanding paths that begin with a tilde (~) followed by a username, the internal parse_tilde function extracts the username to determine the user's home directory. The implementation allocates memory for this username directly on the stack using the strndupa macro. Because the size of this allocation was determined by the length of the user-supplied input without any bounds checks, passing an excessively long username e.g. thousands of characters, forces the thread to exhaust its stack space. Thus if an application passes untrusted, attacker-controlled input to the wordexp function, an attacker can trigger a stack clash. |
| Out-of-bounds read in Windows TCP/IP allows an authorized attacker to disclose information locally. |
| A vulnerability was found in Open5GS up to 2.7.1. This affects the function hss_ogs_diam_s6a_air_cb/hss_ogs_diam_s6a_ulr_cb of the file src/hss/hss-s6a-path.c of the component Diameter S6a Interface. Performing a manipulation of the argument os.len results in stack-based buffer overflow. It is possible to initiate the attack remotely. The exploit has been made public and could be used. Upgrading to version 2.7.2 is able to mitigate this issue. The patch is named e89aa79efe629ae90f59dcdf8847c117d9a7da86. It is suggested to upgrade the affected component. |
| Out-of-bounds read in Microsoft Office Excel allows an unauthorized attacker to disclose information locally. |
| A maliciously crafted input, when processed by the Autodesk Installer IPC frame parser, may trigger improper validation of an input-specified position or offset, resulting in an out-of-range substring operation. A malicious actor may leverage this vulnerability to cause the NT AUTHORITY\SYSTEM service to terminate unexpectedly, resulting in a denial-of-service condition. |
| Heap-based buffer overflow in Microsoft Office Excel allows an unauthorized attacker to execute code locally. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mld: validate sta_mask before ffs() in BA session handlers
Three BA session handlers use ffs(ba_data->sta_mask) - 1 to derive a
station ID without checking that sta_mask is non-zero. When sta_mask is
zero, ffs() returns 0 and the subtraction wraps to 0xFFFFFFFF, causing
an out-of-bounds access on fw_id_to_link_sta[].
Add WARN_ON_ONCE(!ba_data->sta_mask) guards before each ffs() call,
consistent with the existing check in iwl_mld_ampdu_rx_start(). |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: don't wrap around quota ids in dqiterate
LOLLM noticed that q_id is an unsigned 32-bit variable. If it happens
to be set to XFS_DQ_ID_MAX due to a filesystem that actually has a dquot
for ID_MAX, then this addition will truncate to zero and the iteration
starts over. Fix this by casting to u64. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: reject overlapping data areas in SMB2 responses
Commit 53b7c271f06b ("smb: client: restrict implied bcc[0] exemption to
responses without data area") restricted the implied bcc[0] length
exception to responses without a data area. However, the overlap
handling in __smb2_calc_size() clears data_length, which can make an
invalid response appear to have no data area and so qualify for the
exception.
Track data area overlap separately and reject such responses before
applying the length compatibility exceptions. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: raw: reject IP_HDRINCL packets with ihl < 5
raw_send_hdrinc() validates that the caller-supplied IPv4 header
fits within the message length:
iphlen = iph->ihl * 4;
err = -EINVAL;
if (iphlen > length)
goto error_free;
if (iphlen >= sizeof(*iph)) {
/* fix up saddr, tot_len, id, csum, transport_header */
}
It does not, however, reject ihl < 5. For such a packet the
"if (iphlen >= sizeof(*iph))" branch is skipped, leaving the
crafted iphdr untouched, but the packet is still handed to
__ip_local_out() and onward. Downstream consumers that read
iph->ihl assume a sane value: net/ipv4/ah4.c:ah_output() in
particular subtracts sizeof(struct iphdr) from top_iph->ihl * 4
and passes the (signed-int-negative, then cast to size_t)
result to memcpy(), producing an OOB access of length close to
SIZE_MAX and a host kernel panic.
An IPv4 header with ihl < 5 is malformed by definition (RFC 791:
"Internet Header Length is the length of the internet header in
32 bit words ... Note that the minimum value for a correct header
is 5."). The kernel should not be willing to inject such a
packet into its own output path.
Reject "iphlen < sizeof(*iph)" alongside the existing
"iphlen > length" check. This matches the principle that locally
constructed packets that re-enter the IP stack must pass the same
basic sanity tests that a foreign packet would be subjected to.
Once this lands, the "if (iphlen >= sizeof(*iph))" wrapper around
the fixup branch becomes redundant; left in place to keep the
patch minimal and backport-friendly. A follow-up can unwrap it.
Note that commit 86f4c90a1c5c ("ipv4, ipv6: ensure raw socket
message is big enough to hold an IP header") ensures the message
buffer is large enough to hold an iphdr, but does not constrain
the self-reported iph->ihl.
Reachability: the malformed packet source is any caller with
CAP_NET_RAW, including an unprivileged process in a user+net
namespace on a kernel with CONFIG_USER_NS=y. The reproduced AH
crash also requires a matching xfrm AH policy on the outgoing
route; a container granted CAP_NET_ADMIN can install that state
and policy in its netns. Loopback bypasses xfrm_output, so the
trigger uses a real netdev.
Reproduced on UML + KASAN: kernel-mode fault at addr 0x0 with
memcpy_orig at the crash site. Same shape reproduces inside a
rootless Docker container with --cap-add NET_ADMIN on a stock
distro kernel. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/siw: Reject MPA FPDU length underflow before signed receive math
A malicious connected siw peer can send an iWARP FPDU whose MPA length
field (c_hdr->mpa_len, 16 bit big-endian, peer-controlled) is smaller
than the fixed DDP/RDMAP header for the announced opcode. Soft-iWARP
parses the full header in siw_get_hdr() based on iwarp_pktinfo[opcode]
.hdr_len, but never compares mpa_len against that header length.
siw_tcp_rx_data() then derives
srx->fpdu_part_rem = be16_to_cpu(mpa_len) - fpdu_part_rcvd
+ MPA_HDR_SIZE;
where fpdu_part_rcvd equals iwarp_pktinfo[opcode].hdr_len at this
point. For a tagged WRITE (hdr_len 16, MPA_HDR_SIZE 2) the smallest
on-wire mpa_len of 0 yields fpdu_part_rem = -14, and any mpa_len below
hdr_len - MPA_HDR_SIZE underflows to a negative int.
The signed value then flows into siw_proc_write()/siw_proc_rresp() as
bytes = min(srx->fpdu_part_rem, srx->skb_new);
is handed to siw_check_mem() as an int len (whose interval check
addr + len > mem->va + mem->len is satisfied for a valid base when
len is negative), and reaches siw_rx_data() -> siw_rx_kva() /
siw_rx_umem() -> skb_copy_bits() as a signed copy length. The header
copy branch in skb_copy_bits() promotes that to size_t, producing a
multi-gigabyte read.
KASAN under a KUnit harness that drives the real kernel TCP receive
path -- a loopback AF_INET socketpair, the malformed FPDU written via
kernel_sendmsg, sk_data_ready firing in softirq, tcp_read_sock
dispatching to siw_tcp_rx_data -- reports:
BUG: KASAN: use-after-free in skb_copy_bits+0x284/0x480
Read of size 4294967295 at addr ffff888...
Call Trace:
skb_copy_bits
siw_rx_kva
siw_rx_data
siw_check_mem
siw_proc_write
siw_tcp_rx_data
__tcp_read_sock
siw_qp_llp_data_ready
tcp_data_ready
tcp_data_queue
Add the missing invariant at the earliest point where the peer header
is fully assembled. iwarp_pktinfo[*].hdr_len - MPA_HDR_SIZE is exactly
the value the siw transmitter uses as the minimum mpa_len for each
opcode (drivers/infiniband/sw/siw/siw_qp.c:33), so this matches the
protocol contract. Out-of-range FPDUs terminate the connection with
TERM_ERROR_LAYER_LLP / LLP_ETYPE_MPA / LLP_ECODE_FPDU_START -- which
is RFC 5044 Section 8 error code 3 ("Marker and ULPDU Length fields
do not agree on the start of an FPDU"), the correct framing-error
class for this inconsistency. |
| In the Linux kernel, the following vulnerability has been resolved:
exfat: bound uniname advance in exfat_find_dir_entry()
In exfat_find_dir_entry(), each TYPE_EXTEND (file name) entry advances the
output pointer by a fixed amount while the loop guard only tracks the
accumulated name length:
if (++order == 2)
uniname = p_uniname->name;
else
uniname += EXFAT_FILE_NAME_LEN;
len = exfat_extract_uni_name(ep, entry_uniname);
name_len += len;
unichar = *(uniname+len);
*(uniname+len) = 0x0;
uniname grows by EXFAT_FILE_NAME_LEN (15) per name entry, but name_len
grows only by the actual extracted length, which is shorter when a name
fragment contains an early NUL. The only guard is
`name_len >= MAX_NAME_LENGTH`, so a crafted directory with many short
name fragments lets uniname run far past the
p_uniname->name[MAX_NAME_LENGTH + 3] buffer while name_len stays small,
causing an out-of-bounds read and write at *(uniname+len).
The sibling extractor exfat_get_uniname_from_ext_entry() already stops
on a short fragment (the lockstep `len != EXFAT_FILE_NAME_LEN` guard
added in commit d42334578eba ("exfat: check if filename entries exceeds
max filename length")); exfat_find_dir_entry() never got the
equivalent. Track the per-entry write offset as a count and reject a
fragment once the offset, or the offset plus the extracted length, would
exceed MAX_NAME_LENGTH, before forming the output pointer. |
| A flaw has been found in Open5GS up to 2.7.1. Affected by this vulnerability is an unknown functionality of the component freeDiameter. This manipulation causes memory corruption. The attack is possible to be carried out remotely. |
| A vulnerability was identified in Open5GS up to 2.7.1. This issue affects the function pcrf_rx_aar_cb of the file src/pcrf/pcrf-rx-path.c of the component Diameter Rx Handler. The manipulation of the argument num_of_media_component/num_of_sub leads to buffer overflow. The attack can be initiated remotely. The exploit is publicly available and might be used. Upgrading to version 2.7.2 is capable of addressing this issue. The identifier of the patch is 87b4e4535c77ded627cdb6f4e4e2e3ea761f40b7. It is recommended to upgrade the affected component. |
| A vulnerability was determined in Open5GS up to 2.7.1. This vulnerability affects the function mme_s6a_subscription_data_from_avp of the file src/mme/mme-fd-path.c of the component Diameter S6a Interface. Executing a manipulation of the argument msisdn_len can lead to heap-based buffer overflow. It is possible to launch the attack remotely. The exploit has been publicly disclosed and may be utilized. Upgrading to version 2.7.2 is able to resolve this issue. This patch is called 7ea82cb87bb65c3694d8d7c7a5efed1c4d3c9304. Upgrading the affected component is recommended. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: fix double-free of tx_buf skb
If ice_tso() or ice_tx_csum() fail, the error path in
ice_xmit_frame_ring() frees the skb, but the 'first' tx_buf still points
to it and is marked as valid (ICE_TX_BUF_SKB).
'next_to_use' remains unchanged, so the potential problem will
likely fix itself when the next packet is transmitted and the tx_buf
gets overwritten. But if there is no next packet and the interface is
brought down instead, ice_clean_tx_ring() -> ice_unmap_and_free_tx_buf()
will find the tx_buf and free the skb for the second time.
The fix is to reset the tx_buf type to ICE_TX_BUF_EMPTY in the error
path, so that ice_unmap_and_free_tx_buf().
Move the initialization of 'first' up, to ensure it's already valid in
case we hit the linearization error path.
The bug was spotted by AI while I had it looking for something else.
It also proposed an initial version of the patch.
I reproduced the bug and tested the fix by adding code to inject
failures, on a build with KASAN.
I looked for similar bugs in related Intel drivers and did not find any. |
| Axios is a promise based HTTP client for the browser and Node.js. Versions prior to 1.15.0 and 0.3.1 are vulnerable to a specific gadget-style attack chain in which prototype pollution in a third-party dependency may be leveraged to inject unsanitized header values into outbound requests. This vulnerability is fixed in 1.15.0 and 0.3.1. |
