| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: tegra: Fix burst size calculation
Currently, the Tegra GPC DMA hardware requires the transfer length to
be a multiple of the max burst size configured for the channel. When a
client requests a transfer where the length is not evenly divisible by
the configured max burst size, the DMA hangs with partial burst at
the end.
Fix this by reducing the burst size to the largest power-of-2 value
that evenly divides the transfer length. For example, a 40-byte
transfer with a 16-byte max burst will now use an 8-byte burst
(40 / 8 = 5 complete bursts) instead of causing a hang.
This issue was observed with the PL011 UART driver where TX DMA
transfers of arbitrary lengths were stuck. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: ensure inner headers in ICMP errors are in headroom
Sashiko points out that after stripping the outer headers
with pskb_pull() we should ensure the inner IP headers
in ICMP errors from tunnels are present in the skb headroom
for functions like ipv4_update_pmtu(), icmp_send() and
IP_VS_DBG().
Also, add more checks for the length of the inner headers. |
| In the Linux kernel, the following vulnerability has been resolved:
vdpa/octeon_ep: fix IRQ-to-ring mapping in interrupt handler
Look up the IRQ index in oct_hw->irqs instead of assuming
irq - irqs[0]. This supports non-contiguous IRQ numbers and
avoids incorrect ring indexing when irqs[0] is not the base. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Fix TOCTOU heap overflow in get_srq_wqe
get_srq_wqe() reads wqe->dma.num_sge from the shared receive queue
buffer, which is mapped into userspace. It validates num_sge against
max_sge, but then re-reads the same field to calculate the memcpy
size. A concurrent userspace thread can modify num_sge between
validation and use, causing a heap buffer overflow when copying the
WQE into qp->resp.srq_wqe.
Read num_sge into a local variable and use it for both the bounds
check and the size calculation. |
| Go JOSE provides an implementation of the Javascript Object Signing and Encryption set of standards in Go, including support for JSON Web Encryption (JWE), JSON Web Signature (JWS), and JSON Web Token (JWT) standards. Prior to 4.1.4 and 3.0.5, decrypting a JSON Web Encryption (JWE) object will panic if the alg field indicates a key wrapping algorithm (one ending in KW, with the exception of A128GCMKW, A192GCMKW, and A256GCMKW) and the encrypted_key field is empty. The panic happens when cipher.KeyUnwrap() in key_wrap.go attempts to allocate a slice with a zero or negative length based on the length of the encrypted_key. This code path is reachable from ParseEncrypted() / ParseEncryptedJSON() / ParseEncryptedCompact() followed by Decrypt() on the resulting object. Note that the parse functions take a list of accepted key algorithms. If the accepted key algorithms do not include any key wrapping algorithms, parsing will fail and the application will be unaffected. This panic is also reachable by calling cipher.KeyUnwrap() directly with any ciphertext parameter less than 16 bytes long, but calling this function directly is less common. Panics can lead to denial of service. This vulnerability is fixed in 4.1.4 and 3.0.5. |
| GIMP TIF File Parsing Heap-based Buffer Overflow Remote Code Execution Vulnerability. This vulnerability allows remote attackers to execute arbitrary code on affected installations of GIMP. User interaction is required to exploit this vulnerability in that the target must visit a malicious page or open a malicious file.
The specific flaw exists within the parsing of TIF files. The issue results from the lack of proper validation of the length of user-supplied data prior to copying it to a heap-based buffer. An attacker can leverage this vulnerability to execute code in the context of the current process. Was ZDI-CAN-29404. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Fix buffer overflow in SDMA queue checkpoint/restore on GFX11
The v11 MQD manager incorrectly assigned the CP-compute variants of
checkpoint_mqd/restore_mqd for KFD_MQD_TYPE_SDMA queues. These functions
use sizeof(struct v11_compute_mqd) (2048 bytes) instead of sizeof(struct
v11_sdma_mqd) (512 bytes), causing a 1536-byte overflow.
During CRIU checkpoint of an SDMA queue on Navi3x:
- checkpoint_mqd() reads 2048 bytes from a 512-byte SDMA MQD buffer,
leaking 1536 bytes of adjacent GTT memory to userspace
During CRIU restore:
- restore_mqd() writes 2048 bytes into a 512-byte SDMA MQD buffer,
corrupting 1536 bytes of adjacent GTT memory (often the ring buffer
or neighboring MQDs)
This is a copy-paste regression unique to v11. All other ASIC backends
(cik, vi, v9, v10, v12) correctly use the SDMA-specific variants.
Add checkpoint_mqd_sdma() and restore_mqd_sdma() functions that properly
handle the smaller v11_sdma_mqd structure, matching the pattern used in
other MQD managers.
(cherry picked from commit 6fa41db7ffdec97d62433adf03b7b9b759af8c2c) |
| GIMP HDR File Parsing Heap-based Buffer Overflow Remote Code Execution Vulnerability. This vulnerability allows remote attackers to execute arbitrary code on affected installations of GIMP. User interaction is required to exploit this vulnerability in that the target must visit a malicious page or open a malicious file.
The specific flaw exists within the parsing of HDR files. The issue results from the lack of proper validation of the length of user-supplied data prior to copying it to a heap-based buffer. An attacker can leverage this vulnerability to execute code in the context of the current process. Was ZDI-CAN-28266. |
| A security vulnerability has been detected in sonos tract up to 0.23.4. This impacts the function Tensor::from_raw_dt_align of the file data/src/tensor.rs of the component ONNX Initializer Loader. Such manipulation leads to incorrect calculation of buffer size. The attack may be launched remotely. The exploit has been disclosed publicly and may be used. The name of the patch is 66b10bda8895f4bfaf8c205361f0125cdf51f99b. It is best practice to apply a patch to resolve this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: flowtable: use dst in this direction when pushing IPIP header
When pushing the IPIP header, the route of the other direction is used
to calculate the headroom, use the route in this direction. Accessing
the other tuple to set the IP source and destination is fine because
this tuple does not provide such information to avoid storing redundant
information. However, this tuple already provides the dst for this
direction, this went unnoticed because this bug affects headroom and
iph->frag_off only at this stage. |
| In the Linux kernel, the following vulnerability has been resolved:
openvswitch: cap upcall PID array size and pre-size vport replies
The vport netlink reply helpers allocate a fixed-size skb with
nlmsg_new(NLMSG_DEFAULT_SIZE, ...) but serialize the full upcall PID
array via ovs_vport_get_upcall_portids(). Since
ovs_vport_set_upcall_portids() accepts any non-zero multiple of
sizeof(u32) with no upper bound, a CAP_NET_ADMIN user can install a PID
array large enough to overflow the reply buffer, causing nla_put() to
fail with -EMSGSIZE and hitting BUG_ON(err < 0). On systems with
unprivileged user namespaces enabled (e.g., Ubuntu default), this is
reachable via unshare -Urn since OVS vport mutation operations use
GENL_UNS_ADMIN_PERM.
kernel BUG at net/openvswitch/datapath.c:2414!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 1 UID: 0 PID: 65 Comm: poc Not tainted 7.0.0-rc7-00195-geb216e422044 #1
RIP: 0010:ovs_vport_cmd_set+0x34c/0x400
Call Trace:
<TASK>
genl_family_rcv_msg_doit (net/netlink/genetlink.c:1116)
genl_rcv_msg (net/netlink/genetlink.c:1194)
netlink_rcv_skb (net/netlink/af_netlink.c:2550)
genl_rcv (net/netlink/genetlink.c:1219)
netlink_unicast (net/netlink/af_netlink.c:1344)
netlink_sendmsg (net/netlink/af_netlink.c:1894)
__sys_sendto (net/socket.c:2206)
__x64_sys_sendto (net/socket.c:2209)
do_syscall_64 (arch/x86/entry/syscall_64.c:63)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
</TASK>
Kernel panic - not syncing: Fatal exception
Reject attempts to set more PIDs than nr_cpu_ids in
ovs_vport_set_upcall_portids(), and pre-compute the worst-case reply
size in ovs_vport_cmd_msg_size() based on that bound, similar to the
existing ovs_dp_cmd_msg_size(). nr_cpu_ids matches the cap already
used by the per-CPU dispatch configuration on the datapath side
(ovs_dp_cmd_fill_info() serialises at most nr_cpu_ids PIDs), so the
two sides stay consistent. |
| In the Linux kernel, the following vulnerability has been resolved:
macvlan: fix macvlan_get_size() not reserving space for IFLA_MACVLAN_BC_CUTOFF
macvlan_get_size() does not account for IFLA_MACVLAN_BC_CUTOFF, but
macvlan_fill_info() conditionally includes it when port->bc_cutoff != 1.
This causes nla_put_s32() to fail with -EMSGSIZE when the netlink skb
runs out of space, triggering a WARN_ON in rtnetlink and preventing the
interface from being dumped.
The bug can be reproduced with:
ip link add macvlan0 link eth0 type macvlan mode bridge
ip link set macvlan0 type macvlan bc_cutoff 0
ip -d link show macvlan0 # fails with -EMSGSIZE
The bc_cutoff feature was added in commit 954d1fa1ac93 ("macvlan: Add
netlink attribute for broadcast cutoff"), which added the nla_put_s32()
call in macvlan_fill_info() but missed adding the corresponding
nla_total_size(4) in macvlan_get_size(). A follow-up commit
55cef78c244d ("macvlan: add forgotten nla_policy for
IFLA_MACVLAN_BC_CUTOFF") fixed the missing nla_policy entry but still
did not fix the size calculation. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm/dsi: don't dump registers past the mapped region
On DSI 6G platforms the IO address space is internally adjusted by
io_offset. Later this adjusted address might be used for memory dumping.
However the size that is used for memory dumping isn't adjusted to
account for the io_offset, leading to the potential access to the
unmapped region. Lower ctrl_size by the io_offset value to prevent
access past the mapped area.
msm_disp_snapshot_add_block+0x1d4/0x3c8 [msm] (P)
msm_dsi_host_snapshot+0x4c/0x78 [msm]
msm_dsi_snapshot+0x28/0x50 [msm]
msm_disp_snapshot_capture_state+0x74/0x140 [msm]
msm_disp_snapshot_state_sync+0x60/0x90 [msm]
_msm_disp_snapshot_work+0x30/0x90 [msm]
kthread_worker_fn+0xdc/0x460
kthread+0x120/0x140
Patchwork: https://patchwork.freedesktop.org/patch/721747/ |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SEV: Compute the correct max length of the in-GHCB scratch area
When setting the length of the GHCB scratch area, and the area is in the
GHCB shared buffer, set the effective length of the scratch area to the max
possible size given the start of the guest-provided pointer, and the end of
the shared buffer.
The code was "fine" when first introduced, as KVM doesn't consult the
length of the buffer when emulating MMIO, because the passed in @len always
specifies the *max* size required. But for PSC requests, the incoming @len
is just the minimum length (to process the header), and KVM needs to know
the full size of the scratch area to avoid buffer overflows (spoiler alert).
Opportunistically rename @len => @min_len to better reflect its role. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: safe_serial: fix memory corruption with small endpoint
Make sure that the bulk-out buffer size is at least eight bytes to avoid
user-controlled slab corruption in "safe" mode should a malicious device
report a smaller size. |
| A vulnerability has been identified in the GRUB (Grand Unified Bootloader) component. This flaw occurs because the bootloader mishandles string conversion when reading information from a USB device, allowing an attacker to exploit inconsistent length values. A local attacker can connect a maliciously configured USB device during the boot sequence to trigger this issue. A successful exploitation may lead GRUB to crash, leading to a Denial of Service. Data corruption may be also possible, although given the complexity of the exploit the impact is most likely limited. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: Reserve an extra page for early kernel mapping
The final part of [data, end) segment may overflow into the next page of
init_pg_end[1] which is the gap page before early_init_stack[2]:
[1]
crash_arm64_v9.0.1> vtop ffffffed00601000
VIRTUAL PHYSICAL
ffffffed00601000 83401000
PAGE DIRECTORY: ffffffecffd62000
PGD: ffffffecffd62da0 => 10000000833fb003
PMD: ffffff80033fb018 => 10000000833fe003
PTE: ffffff80033fe008 => 68000083401f03
PAGE: 83401000
PTE PHYSICAL FLAGS
68000083401f03 83401000 (VALID|SHARED|AF|NG|PXN|UXN)
PAGE PHYSICAL MAPPING INDEX CNT FLAGS
fffffffec00d0040 83401000 0 0 1 4000 reserved
[2]
ffffffed002c8000 (r) __pi__data
ffffffed0054e000 (d) __pi___bss_start
ffffffed005f5000 (b) __pi_init_pg_dir
ffffffed005fe000 (b) __pi_init_pg_end
ffffffed005ff000 (B) early_init_stack
ffffffed00608000 (b) __pi__end
For 4K pages, the early kernel mapping may use 2MB block entries but the
kernel segments are only 64KB aligned. Segment boundaries that fall
within a 2MB block therefore require a PTE table so that different
attributes can be applied on either side of the boundary.
KERNEL_SEGMENT_COUNT still correctly counts the five permanent kernel
VMAs registered by declare_kernel_vmas(). However, since commit
5973a62efa34 ("arm64: map [_text, _stext) virtual address range
non-executable+read-only"), the early mapper also maps [_text, _stext)
separately from [_stext, _etext). This adds one more early-only split
and can require one more page-table page than the existing
EARLY_SEGMENT_EXTRA_PAGES allowance reserves.
Increase the 4K-page early mapping allowance by one page to cover that
additional split.
[catalin.marinas@arm.com: rewrote part of the commit log]
[catalin.marinas@arm.com: expanded the code comment] |
| In the Linux kernel, the following vulnerability has been resolved:
net: pull headers in qdisc_pkt_len_segs_init()
Most ndo_start_xmit() methods expects headers of gso packets
to be already in skb->head.
net/core/tso.c users are particularly at risk, because tso_build_hdr()
does a memcpy(hdr, skb->data, hdr_len);
qdisc_pkt_len_segs_init() already does a dissection of gso packets.
Use pskb_may_pull() instead of skb_header_pointer() to make
sure drivers do not have to reimplement this.
Some malicious packets could be fed, detect them so that we can
drop them sooner with a new SKB_DROP_REASON_SKB_BAD_GSO drop_reason. |
| In the Linux kernel, the following vulnerability has been resolved:
soc/tegra: cbb: Fix incorrect ARRAY_SIZE in fabric lookup tables
Fix incorrect ARRAY_SIZE usage in fabric lookup tables which could
cause out-of-bounds access during target timeout lookup. |
| In the Linux kernel, the following vulnerability has been resolved:
virt: sev-guest: Do not use host-controlled page order in cleanup path
When issuing an extended guest request (SVM_VMGEXIT_EXT_GUEST_REQUEST),
get_ext_report() allocates a buffer to retrieve a certificate blob from the
host, keeping track of its size in report_req->certs_len.
However, the host may return SNP_GUEST_VMM_ERR_INVALID_LEN, indicating
an invalid buffer size, as well as the expected length of such buffer.
get_ext_report() subsequently updates report_req->certs_len with the
host-controlled value, and cleans up the buffer by computing a page order
from such value. This is incorrect, as the host-provided length may not
match the page order of the original allocation, potentially resulting
in corruption in the page allocator.
Fix this by using alloc_pages_exact() instead, and reusing @npages to
compute the size passed to free_pages_exact(). For consistency, also
use @npages to compute the size when allocating the pages, even though
this last change has no functional effect. |
